Kits & Bundles

PiShop kits and bundles
Sort By:  
Avoidance tracking Smart Robot Car Chassis Kit Speed Encoder Battery Box 2WD Ultrasonic module For Arduino kit (Aduino robot car)
Please Note: Some drilling will be required. You might need to add a few standoffs and screws to build it the way you want it.
Description:

This complete robot car kit includes the arduino as well. Just add batteries and code. Great for beginners to learn how to code using sensors and motion on the Arduino boards

Pdf manual available at http://www.cs.columbia.edu/~sedwards/presentations/robot-car-instructions.pdf 
Get more details at https://create.arduino.cc/projecthub/hda-robotics/project-1-2wd-obstacle-avoiding-robot-390ef8

Package Includes: 
  • Car chassis x 1 
  • Car Wheels x 2 
  • DC Gear Motor x 2 
  • 20 line gun code disk x 2 
  • Fasteners (high intensity black acrylic) x 4 
  • Caster x 1 
  • Four battery box x 1 
  • Quality Rocker Switch x 1 
  • Assembly drawing x 1
  • Several screws and nuts
  • V5 shield x 1
  • UNO R3 x 1
  • SG90 x 1
  • FPV x 1
  • L298N x 1
R599.90  Inc VAT
Rear Bike Light Project Kit (KT bike kit)
Product Description

This easy build bike light kit has just ten parts, making it a good introduction to electronics. The kit uses two ultra bright red LEDs, which flash rapidly, providing a highly visible light. Making it ideal for use as a rear bike light.

Alternatively it can be used as a night safety product or flashing eyes.

Features:

  • Easy build kit making a great introduction to electronics.
  • Great visibility for night time safety.

Contents:

  • 1 x 2xAA Battery Cage with Leads.
  • 2 x 470K Resistor.
  • 1 x 33R Resistor.
  • 2 x Capacitor, Electrolytic, 16V, 10uF.
  • 2 x BC547 NPN Transistor.
  • 2 x Red 5mm Water Clear LED - 30deg - 1000mCd.

Dimensions:

  • Length: 48.5mm.
  • Width: 25.5mm.

Requires:


Resources:


This easy build bike light kit has just ten parts, making it a good introduction to electronics. The kit uses two ultra bright red LEDs, which flash rapidly, providing a highly visible light. Making it ideal for use as a rear bike light.

Alternatively it can be used as a night safety product or flashing eyes.

Caution:

  • This is an educational kit and should be used in conjunction with a commercially available bike light.
R59.90  Inc VAT
Easy Build Timer Project Kit (KT timer kit)
Product Description

With its low part count this easy build timer project makes a good introduction to electronics. The timer uses a resistor capacitor network to provide a time delay of between 1 second and 4 minutes, which is set by the PCB mount variable resistor. When the button is pressed the LED changes from red to green, then at the end of the time interval it turns red.

Features:

  • Easy build timer kit.
  • When the time set has been reached the LED changes colour.
  • The time delay can be adjusted via the variable resistor.

Contents:

  • 1 x 2AA Battery Cage.
  • 1 x 47Ω Resistor.
  • 2 x 10KΩ Resistors.
  • 1 x 1MΩ Potentiometer.
  • 1 x Capacitor, Electrolytic, 10V, 1 mF.
  • 1 x BC558 PNP Transistor.
  • 1 x Tri colour 5mm diffused LED - 650mCd.
  • 1 x 6mm PCB Mount Tactile Switch 9.5mm Height.
  • 1 x Easy Build Timer PCB

Dimensions:

  • PCB Length: 54mm.
  • PCB Width: 26mm.

Requires:


Resources:

Note:

  • This kit requires soldering.
R69.90  Inc VAT
Air Freshener Kit (KT fan kit)
Product Description

This kit uses a silent low current motor to spin a fan, making it perfect to circulate air through an air freshener containing potpourri or it can be used to move a light weight buggy. The electronics take no power in standby and when the switch is pressed the motor spins for up to 100 seconds. This time is adjustable via the on board variable resistor.

Features:

  • Silent motor.
  • Adjustable timer.

Contents:

  • 1 x Battery Holder With Leads (2x AA).
  • 1 x 1K Resistor 5%.
  • 1 x 1M resistor.
  • 1 x PCB Trimmer 1M POT.
  • 1 x 16V 220uF Electrolytic Capacitor.
  • 2 x BC547 NPN Transistor.
  • 1 x Miniature Push to Make Switch, Red.
  • 1 x Low Inertia Solar Motor - 1820 RPM.
  • 1 x 55mm White Four Blade Miniature Impeller.
  • 0.5m Connecting Wire.
  • 1 x Air Freshener PCB.

Dimensions:

  • Length: 46mm.
  • Width: 28mm.

Requires:

Resources:

This kit is supplied in a grip seal bag.


R99.90  Inc VAT
Heat Activated Switch (KT heat switch kit)
Product Description

This temperature activated project kit is also available as a light activated project kit. The output of this board can be used to control other electronic circuits, turning them on automatically when it goes hot or cold.

The board has space for an LED with current limit resistor (both available separately) which will light when the output turns on.

The Darlington pair transistor configuration allows an output current of up to half an amp to be controlled. Operating voltage 3V to 10V (lower voltages allow for better adjustment of the switching point).

Features:

  • The Temperature Switch Kit detects the temperature of its surroundings using a thermistor.
  • The kit acts as an automated on/off switch (temperature dependent).

Contents:

  • 1 x 47KΩ Potentiometer.
  • 2 x BC337 NPN Transistors.
  • 1 x Thermistor.
  • 1 x 220Ω Resistor.
  • 1 x Heat Activated Switch PCB

Possible applications include:

  • Babies bath over temperature indicator.
  • Automatic fan.

Dimensions:

  • PCB Length: 53mm.
  • PCB Width: 25.5mm.

Requires:


Resources:


Note:

  • This kit requires soldering.
R53.90  Inc VAT
Relay Board (KT relay kit)
Product Description

This is a versatile relay board kit that can easily be configured via jumpers and trimmer potentiometers to do a range of tasks.

Most sensor and switches can be connected to the input of the board and the trigger level set for the input device. This can be inverted if required, then there is the option to feed this straight to the relay or a timer of up to 25 minutes can be used. Irrespective of the state of the invert jumper whenever the sense LED goes from off to on the timer restarts.#

The board can run off any voltage from 4.5 to 6 volts.

The output cans switch DC or mains.

This datasheet details what the board does and how to use it along with some worked examples. A more detailed set of information including the build instructions & how to configure the kit can also be downloaded.

Click here to download the full teaching notes pdf_icon.gif

WARNING: Using mains electricity can be dangerous and should only be attempted by qualified electricians.

This kit includes:

  • 3 x 100Kohm resistors
  • 3 x 220ohm resistors
  • 1 x 47Kohm resistors
  • 1 x 1Mohmpotentiometer
  • 1 x 10Mohm potentiometer
  • 2 x 1N4001 diodes
  • 2 x 5mm red LEDs
  • 1 x 100uF capacitors, electrolytic
  • 1 x 4.7uF capacitors, electrolytic
  • 1 x 2N7000 n-channel FET
  • 2 x 2 way terminal blocks
  • 1 x 3 way terminal blocks
  • 1 x LM324 operational amplifier IC
  • 1 x 14 pin IC holder
  • 2 x 3 way pinstrip
  • 2 x Jumpers
  • 1 x Relay
  • 1 x Relay board PCB

PCB dimensions: 86.5mm x 49mm.

This kit is supplied as a pack of parts and requires soldering.

R159.90  Inc VAT
Deluxe Rear Bike Light Kit (KT deluxe bike kit)
Product Description

The Kitronik Deluxe Rear Bike Light Kit is easy to build kit and is an excellent way to learn about the very popular 555 timer IC. The kit uses four ultra bright LEDs that can be operated in two modes; constant and flashing.

A key design aim of the kit was that it should conform to all relevant British Standard measures. Both the flash rate and brightness conform to British Standards for vehicle road lighting (2005), making it ideal for use as a rear bike light. Alternatively, it can be used as a night safety product or flashing eyes.

During testing we connected the kit to 3 x AAA batteries and ran it continuously. At 80 hours of continuous use the LEDs were still lit at full brightness. After 107 hours, although still lit, the brightness had dropped below the level at which you would want to use them. So, we estimate that with brand new batteries you could comfortably run the light for 2 hours of daily commuting for at least an entire month with the LEDs still at full brightness.

Features:

  • An easy to build rear bike light project that conforms to British Standards for vehicle road lighting (2005) for both brightness and flash rate.
  • Learn about the very popular 555 timer IC.
  • The kit features 4 x bright LEDs.
  • It has two operating modes; continuous and flashing.
  • Its compact design makes it the ideal choice for designing custom enclosures.

Contains:


Dimensions:

  • PCB Length: 52.6mm.
  • PCB Width: 37.6mm.
  • PCB Thickness: 1.6mm.

Video: https://youtu.be/KPPh7Nwa1ts

Requires:


Resources:

R104.90  Inc VAT
Electro-Fashion Starter Pack, Standard Cell Holder (Fashion Starter Pack)
Product description:

This pack is a great way to get started with E-Textiles.

We have selected a number of products from our Electro-Fashion range, including three of our ultra-slim LEDs and two seperate power boards. There are enough components for you get started immediately to create some eye catching E-Textiles projects, the only limit is your imagination.

Features:

  • Everything you need to complete two projects.
  • Enough Electro-Fashion components to get started immediately with E-Textiles.
  • Full instructions for assembly.
  • Great project ideas and tutorials.

Contents:

  • 2 x Coin Cell Holder.
  • 3 x Sewable LEDs  White.
  • 3 x Flashing LEDs White.
  • 1 x Slide Switch.
  • 1 x Push Switch.
  • 2 x CR2032 Coin Cell Batteries.
  • 1 x 6m Conductive Thread.

Dimensions:

  • Sewable Coin Cell Holder Length: 34mm.
  • Sewable Coin Cell Holder Width: 20mm.
  • Sewable Coin Cell Holder Height: 4.5mm.
  • Ultra Slim Sewable LED Length: 15mm.
  • Ultra Slim Sewable LED Width: 6.5mm.
  • Ultra Slim Sewable LED Height: 2.7mm.
  • Slide Switch Length: 18mm.
  • Slide Switch Width: 8.5mm.
  • Slide Button Switch Height: 4mm.
  • Push Button Switch Length: 18mm.
  • Push Button Switch Width: 8.5mm.
  • Push Button Switch Height: 3mm.
  • CR2032 Battery Height: 3.2mm.
  • CR2032 Battery Diameter: 20mm.

Requires:


Resources:


Caution:

  • The coin cell holders in this pack contain Nickel and should not be used in designs where it will be in prolonged contact with the skin.
R289.90  Inc VAT
The PiHut's Ultimate 5MM LED Kit (PiHut 5MM LED Kit)
Description:

The ultimate 5MM LED kit, containing 300 LEDs of various colours/styles in a hardy component box with a secure clasp! Each LED type is packed separately with it's value clearly labelled on the outer pouch.
Can never remember which leg is positive and which is negative? Fear not, we've included a handy "LED map" on the inside of the box.
 
Included Values: 

Clear Lens:
  • 20x 5mm Green LED
  • 20x 5mm White LED
  • 20x 5mm Yellow LED
  • 20x 5mm Red LED
  • 20x 5mm Blue LED
  • 20x 5mm Pink LED
  • 20x 5mm Orange LED
  • 20x 5mm Purple LED
Diffused Lens:
  • 20x 5mm Green LED
  • 20x 5mm White LED
  • 20x 5mm Yellow LED
  • 20x 5mm Red LED
  • 20x 5mm Blue LED
Extras:
  • 20x 5mm RGB LED (slow flash)
  • 20x 5mm RGB LED (fast flash)
R129.90  Inc VAT
The PiHut's Ultimate 3MM LED Kit (PiHut 3MM LED Kit)
Description:

The ultimate 3MM LED kit, containing 300 LEDs of various colours/styles in a hardy component box with a secure clasp! Each LED type is packed separately with it's value clearly labelled on the outer pouch.

 

Can never remember which leg is positive and which is negative? Fear not, we've included a handy "LED map" on the inside of the box.
 
Included Values: 
Clear Lens:
  • 20x 3mm Green LED
  • 20x 3mm White LED
  • 20x 3mm Yellow LED
  • 20x 3mm Red LED
  • 20x 3mm Blue LED
  • 20x 3mm Pink LED
  • 20x 3mm Orange LED
  • 20x 3mm Purple LED
Diffused Lens:
  • 20x 3mm Green LED
  • 20x 3mm White LED
  • 20x 3mm Yellow LED
  • 20x 3mm Red LED
  • 20x 3mm Blue LED
Extras:
  • 20x 3mm RGB LED (slow flash)
  • 20x 3mm RGB LED (fast flash)
R149.90  Inc VAT
CamJam EduKit (CamJam EduKit)
Description:

The CamJam EduKit is your way into the world of building electronic circuits and programming the Raspberry Pi in Python.

 Specifications:

The CamJam EduKit features the following components all neatly packaged in a tin:
• A 400pt breadboard
• 3 LEDs (Red, Yellow and Green)
• A button
• A buzzer
• Resistors and jumper cables

 

The kit is accompanied by a set of downloadable worksheets that will take you through a series of exercises from writing a simple program in the Python programming language to lighting up LEDs, reading button presses and making a buzzer go beep! Whereas other products come pre-assembled, the CamJam EduKit introduces you to the world of breadboarding and building electronic circuits yourself, which we think is much more exciting!

 

All the worksheets are freely available to download from http://camjam.me/edukit

 

The CamJam EduKit is a joint venture between The Pi Hut and the Cambridge Raspberry Jam (CamJam). Profits from the sale of the kit will go to CamJam so that they can continue their educational and community work.
R119.90  Inc VAT
CamJam EduKit 2 - Sensors (CamJam EduKit #2)
Description:

The CamJam EduKit #2 is the latest edition to the EduKit family!

The kit is accompanied by a set of (currently 6) downloadable worksheets (or lesson plans for you educators!) that will take you through a series of exercises and projects, teaching you how to make the most of your kit. Whats best is that there is no soldering required, each high quality component is breadboard friendly!

 

All the worksheets are freely available to download from http://camjam.me/edukit

 

Kit Contents:
  • 1 x Breadboard
  • 1 x Immersible temperature Sensor
  • 1 x PIR Sensor
  • 1 x LDR
  • 1 x Active Buzzer
  • 1 x Red 10mm LED
  • 1 x Blue 10mm LED
  • 1 x 4.7K Resistor
  • 2 x 330 Resistor
  • 10 x M/F Jumper Wires
  • 4 x M/M Jumper Wires
  • 1 x Presentation Tin

 

Here are just 4 cool projects you could use the kit for:
  • Make a burglar alarm for your bedroom.
  • Switch on an LED when it gets dark.
  • Have an alarm go off when it’s freezing outside.
  • Test whether the light really does go off in the fridge when you shut the door.

 

Still not convinced? Check out these awesome articles on the kit!

 

The CamJam EduKit is a joint venture between The Pi Hut and the Cambridge Raspberry Jam (CamJam). Profits from the sale of the kit will go to CamJam so that they can continue their educational and community work.
R179.90  Inc VAT
CamJam EduKit 3 - Robotics (CamJam EduKit 3 Robotics)
Description:

The third in the series is here! The CamJam EduKit #3 is focused on robotics and contains (almost) everything you need to create your very own Raspberry Pi-powered robot.

All you need to do is to add your own chassis, Raspberry Pi (any model) & batteries! Then, follow the worksheets to make your own motorized buggy. Add the included sensors and you will soon be detecting objects in front of your robot and following line courses. Included in the kit are the following components:

  • A custom-designed, pre-soldered motor controller board (with screw terminals)
  • Two DC motors (with wires pre-soldered)
  • Two custom red wheels (which go extra fast… because they’re red!)
  • A ball castor (used as the ‘third wheel’ to your robot)
  • A small breadboard (to create your circuits)
  • Two pieces of strong 3M padded double-sided tape
  • A battery box for 4 AA batteries (batteries not included)
  • An ultrasonic distance sensor (for detecting objects in front of your robot)
  • A line follower sensor (for detecting and following black lines)
  • Resistors and jumper cables with which to complete your circuits
  • A strong cardboard box to keep it all in… or to cut into to make your chassis!

All the worksheets are freely available to download from http://camjam.me/edukit

 

Got a 3D printer? Daniel Bull has very kindly designed an awesome chassis, available from Thingiverse ..



Alex Eames over at Raspi.TV got his hands on a prototype, here's what he did!
https://youtu.be/LJDEV7rGwaM

And here's a fantastic unboxing video from Average Man vs Raspberry Pi!
https://youtu.be/KPYWNXiItwo

And another review! This time from TheRaspberryPiGuy! Thanks Matt!
https://youtu.be/TMjd0UrH2PY



R399.90  Inc VAT
Arduino starter kit - UNO compatible (Arduino UNO kit)
Description:

This kit is a great way to start your arduino learning experience and includes the following:


You might also like our handy GET STARTED WITH ARDUINO book.

Need to make your UNO project more mobile? Have a look at our battery solutions:


We do also stock enclosures for the Arduino
R409.61  Inc VAT
Picade DIY kit - 10 inch display including Raspberry Pi 4 1GB (Picade 10 incl Pi41)

Description:

The ultimate desktop retro arcade machine! Picade is a Raspberry Pi-powered mini arcade that you build yourself, with authentic arcade controls, a high resolution 4:3 display that's ideal for retro gaming, and a punchy speaker to hear those 8-bit game soundtracks at their best

Picade is now Raspberry Pi 4 compatible and includes a new USB-C version of Picade X HAT!

The all-new Picade has been completely redesigned, from the inside out! There's new artwork, a new display and display driver board, dedicated power button, an all-new Picade X HAT (now with USB-C), easier wiring, easier access to the interior of the cabinet, beautiful new packaging, a bunch of extra goodies (stickers and an enamel Picade pin), and a gorgeous Picade poster and assembly instructions.

Picade comes in kit form, and it'll take around two to three hours to build. The cabinet is made from powder-coated MDF, giving it a quality look and feel similar to a full-size arcade. All you'll need to add is a Raspberry Pi, USB-C power supply, and micro-SD card.


You can watch a video on  Picade at https://youtu.be/5iUuOH1Ip4A

Cabinet features

  • Black, powder-coated panels
  • Acrylic marquee and console with authentic artwork
  • Push-fit arcade buttons
  • Joystick with black ball top
  • 3" speaker (5W, 4Ω)
  • Easy access with removable back panel
  • Dedicated illuminated power button
  • Grippy rubber feet
  • Dimensions: 350x230x210mm

10-inch display features

  • 1024x768 (4:3 ratio) IPS (wide viewing angle) display
  • Pimoroni-designed and manufactured HDMI display driver board and keypad controls
  • Powered by micro-USB cable (included) from your Pi

Picade X HAT features

  • Easy DuPont connectors for buttons and joystick
  • Push-fit speaker terminals
  • I2S audio DAC with 3W amplifier (mono)
  • Power management, power switch pins, and power button
  • 4-way joystick inputs
  • 6 player buttons
  • 4 utility buttons
  • Metal standoffs to hold your Picade X HAT securely

Extras

  • Picade enamel pin badge
  • Pimoroni Super Sticker Selection
  • Picade poster / assembly instructions

What's new!?

The cabinet is more compact, so it fits more neatly on your desk, but has a higher resolution 8"  or 10" display (1024x768). The display is driven by a new Pimoroni-designed and manufactured driver board, with keypad controls. It's an IPS panel, so it looks great from any viewing angle!

The all-new Picade X HAT is packed full of useful features. We've moved from more fiddly screw terminals to simple DuPont connectors that just push in, and the speaker terminals are the same easy push-fit connectors that we use on pHAT BEAT.

There's dedicated power management on-board Picade X HAT; just plug your micro-USB power supply into the HAT and it'll power your Pi through its pins. The power button connected to the HAT means that once your Pi is safely shutdown, the power will be cut completely to the Pi. A simple press of the power button will boot your Picade up again.

The new buttons in Picade are lower profile, and the new joystick has a single connector rather than the eight spade connectors on our previous Picade joystick.

A gorgeous new neon-look Picade logo on the marquee, and rainbow stripes on the console and screen-surround, evoke classic consoles, as do the assembly instructions and poster.

Building your Picade

We hope the included assembly instructions have everything you need to build your Picade, but we've also filmed a complete build video of Picade that you can watch as you build and learn some handy tips and tricks. Find it at https://youtu.be/gTgu1fUVsmw

The sections are also available separately in a playlist here.

We've also put together an online tutorial that incorporates the assembly instructions, important tips and amendments, and the videos for each section, so do check that out!

Software setup

We recommend the RetroPie operating system for your Picade. You can download it from the RetroPie website and then burn it to a micro-SD card with Etcher.

Connect a USB keyboard to your Pi, and connect to Wi-Fi in the RetroPie menu. Press F4 to exit to the terminal and then type curl https://get.pimoroni.com/picadehat | bash to run the Picade HAT installer.

Reboot your Pi, if it doesn't prompt you to. Press the "Alt" key on your keyboard and then select "Configure input" to configure your Picade's controls. You'll find that the sound and power button should both be working now too!

Notes

If your Picade display doesn't show anything when you first power it up, then it could be because the HDMI display is not being detected by the Raspberry Pi. This can happen because power isn't supplied to the USB ports on the Raspberry Pi for the first few seconds of booting. The solution is to edit the /boot/config.txt file on your RetroPie SD card, and add hdmi_force_hotplug=1 on a new line at the bottom of the file.

If you'd like to design your own artwork for your Picade, then we've made a handy PDF that has the outlines and dimensions of the marquee, screen shim, and console. You can download it from the Picade HAT GitHub repo here.

Where to find ROMs for RetroPie (free and legally) https://howchoo.com/g/otiwyjhlnzb/where-to-find-roms-for-retropie

and here http://cvaddict.com/article.php?articleid=15

What's in the box?

1 x DIY Picade
1 x Raspberry Pi 4 model B 1GB

R5,199.90  Inc VAT
Breadboard Jumper Wire Kit (140pcs) (loose Jumper Wire Kit)
Description:

This is the jumper wires that I have been dreaming of :) This is a box full of color-coded assortment of small jumper wires, great for prototyping. And it is pre-cut, stripped and bent at both ends with the standard breadboard spacing, perfect for classroom and when you do experiment with breadboard.

The best is it comes in a proper plastic box. There are 140 wires in total with different lengths. So get ready for it.

Note: Breadboard not included - Click HERE to get yours !

Features:

  • Wide application: designed to work well with any breadboards or anywhere jumper wires are needed, perfect for breadboard projects.
  • Easy to use: all the colored jumper wires are pre-stripped and preformed right-angled, easy to insert into breadboard.
  • Complete specification: this kit includes 14 different lengths of jumper wires which can satisfy all your need.
  • Storage box: come with a free plastic box, keep your jumper wire kit organized, convenient for store and fetch.
  • These leads are flexible, durable and easy to connect and disconnect, ideal for prototyping use.

Specifications:

  • Material: Plastic Metal.
  • Quantity: 140 pcs.
  • Color: Rainbow color with red, yellow, green, white, blue, orange and grey.
  • Wire Length: 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, 125mm (10pcs each length).

What's in the box ?

  • 140 x Jumper Wires
  • 1 x Storage Box



Note: Breadboard not included - Click HERE to get yours !



R59.90  Inc VAT
120Pcs/lot 15Value 50V 1uF-2200uF Electrolytic Capacitor Kit (120 capacitor kit)
Description:

This useful kit can be used for your electronic projects or repairs.

Structure: Fixed capacitors
Type: Aluminum Electrolytic Capacitors
Resistance: 1UF~ 2200UF ohm
Voltage: 50V
Colour: Black
Quantity: 120PCS


What's in the box?

Capacitance   Voltage  Size(mm)   Quantity 

1UF                    50V         5*11         10PCS

2.2UF                 50V         5*11         10PCS

3.3UF                 50V         5*11         10PCS

4.7UF                 50V         5*11         10PCS

6.8UF                 50V         5*11         10PCS

10UF                  50V         5*12         10PCS

22UF                  50V         5*11         10PCS

33UF                  50V         5*12         10PCS

47UF                  50V         6*12         10PCS

100UF               50V         7*13          5PCS

220UF               50V        10*13         5PCS

330UF               50V        10*17         5PCS

470UF               50V        10*20         5PCS

1000UF            50V         13*25         5PCS

2200UF            50V         16*30         5PCS


Resources:
Theory
Introduction
Types

This useful kit can be used for your electronic projects or repairs.
R178.78  Inc VAT
R239.90
Odseven Ultimate Resistor Kit (OD7 resistor kit)
Description:

The ultimate resistor kit, containing 575 resistors (1/4W metal film) of various values in a hardy component box with a secure clasp! Each resistor value is packed separately with it's value clearly labelled on the outer pouch.
Don't worry if you get them mixed up - there's a handy resistor value calculator on the inside of the box!

Included Values: 
  • 25x 0 Ohm ±1%
  • 25x 10 Ohm ±1%
  • 25x 20 Ohm ±1%
  • 25x 47 Ohm ±1%
  • 25x 470 Ohm ±1%
  • 25x 2.2k Ohm ±1%
  • 25x 4.7k Ohm ±1%
  • 25x 22k Ohm ±1%
  • 25x 47k Ohm ±1%
  • 25x 100k Ohm ±1%
  • 25x 220k Ohm ±1%
  • 25x 470k Ohm ±1%
  • 25x 1M Ohm ±1%
  • 50x 100 Ohm ±1%
  • 50x 220 Ohm ±1%
  • 50x 330 Ohm ±1%
  • 50x 1k Ohm ±1%
  • 50x 10k Ohm ±1%

What's in the box?

1 x resistor kit
R178.90  Inc VAT
Plusivo BJT Transistors Assortment Kit (Plusivo transistor kit)
Description

This is the perfect kit for experimenting with transistor, it includes the most common PNP and NPN transistors: 2N3904, 2N3906, S8050, 2N2907, S8550, 2N2222, BC337, C1815, BC327, A1015.


With this 210 pcs bipolar transistor pack you will never have to worry about not having the right transistor for your circuit. The transistor kit comes with a 250 pcs bonus resistor assortment kit that includes the most commonly used resistor values, always useful for your electronic circuits.

Having a well-designed transistor kit on hand means no more guesswork and frustration when designing and testing your circuits.
You can depend on it to always find the transistors you need.

Features:

  • A transistor kit that includes most commonly used transistor types.
  • A complete transistors assortment kit, so that you always have the PNP and NPN transistors you need.
  • A premium BJT transistor kit that is easy to store and use. It comes with an organizer box.

What's in the box?

  • 1 x 10 compartments plastic box
  • 21 x Transistor 2N3904
  • 21 x Transistor 2N3906
  • 21 x Transistor S8050
  • 21 x Transistor 2N2907
  • 21 x Transistor S8550
  • 21 x Transistor 2N2222
  • 21 x Transistor BC337
  • 21 x Transistor C1815
  • 21 x Transistor BC327
  • 21 x Transistor A1015
  • Bonus Pack: (in paper box)
    • 10 x Resistor 47 Ω
    • 10 x Resistor 100 Ω
    • 10 x Resistor 220 Ω
    • 10 x Resistor 330 Ω
    • 10 x Resistor 470 Ω
    • 10 x Resistor 680 Ω
    • 10 x Resistor 1 kΩ
    • 10 x Resistor 2.2 kΩ
    • 10 x Resistor 3.3 kΩ
    • 10 x Resistor 4.7 kΩ
    • 10 x Resistor 6.8 kΩ
    • 10 x Resistor 10 kΩ
    • 10 x Resistor 22 kΩ
    • 10 x Resistor 33 kΩ
    • 10 x Resistor 47 kΩ
    • 10 x Resistor 68 kΩ
    • 10 x Resistor 100 kΩ
    • 10 x Resistor 330 kΩ
    • 10 x Resistor 470 kΩ
    • 10 x Resistor 680 kΩ
    • 10 x Resistor 1 MΩ
R99.90  Inc VAT
120Pcs/lot 12Value 50V 0.22uF-470uF Electrolytic Capacitor Kit (120/12 capacitor kit)
Description:

This useful kit can be used for your electronic projects or repairs.

Structure: Fixed capacitors
Type: Aluminum Electrolytic Capacitors 0.22uF~ 470UuF
Voltage: 50V
Colour: Black
Quantity: 120PCS


What's in the box?

  • 1.   50V 0.22μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 2.   50V 0.47μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 3.   50V     1 μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 4.   50V   2.2μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 5.   50V   4.7μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 6.   50V    10μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 7.   50V    22μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 8.   16V    33μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 9.   16V    47μF ±20% 105°C  Φ 4 x 7 mm  10pcs
  • 10. 16V  100μF ±20% 105°C  Φ 5 x 7 mm 10pcs
  • 11. 16V  220μF ±20% 105°C  Φ 5 x 7 mm 10pcs
  • 12. 16V  470μF ±20% 105°C  Φ 6 x 7 mm 10pcs

Resources:
Theory
Introduction
Types

This useful kit can be used for your electronic projects or repairs.
R109.90  Inc VAT
Per Page      21 - 40 of 71