Generic3
It makes it easy to connect wires to your pcb.
Electrical Properties
- Rated voltage: 300V
- Rated current: 16A
- Contact resistance: 20mΩ
- Insulation resistance: 5000MΩ/1000V
- Withstanding voltage: AC1500V/1Min
Mechanical Properties
- Temp. Range: -30℃~ 120℃
- Max Soldering: 250℃ for 5 Sec
- Torque: 0.5Nm
Specifications
- Screws: M2.5 steel Zinc plated
- Contact: phosphor bronze Ni plated or stainless steel
- Pin header: Brass, Tin plated
- Housing: PBT, UL94V-0
- Pitch: 5.08mm
- Poles: 3P
- Colour: Blue
What's in the box?
5 x 3 pin Terminal Blocks
- Motor Diameter: 4mm
- Motor Length: 8mm
- Eccentric Wheel Size: 4.4x4.4mm
- Voltage: DC1.5-3V
- Current: 0.15-0.23A
Features
- Stable and reliable performance.
- Easy disassembly type.
- Easy to clean and maintain.
- Excellent quality and long service life.
- Has been widely applied in RC car, RC aircraft.
Laser Safety Glasses 200-450nm Eye Protection Green Lens. Not suitable for high power laser, only suitable for low power laser. Laser light is harmful to human eyes, please choose these goggles to protect your eyes!
- Brand: Eleksmaker
- Material: Plastic
- Item: Laser Protective Glasses
- Applicable Model: 200-450nm Wavelength
- Optical Density (OD): OD4
- Blue Laser Visible Light Transmission: <50%
- Red Laser Visible Light Transmission: >60%
Features
- Durable and comfortable to wear.
- Fit for 200-450nm blue-violet lasers.
- Ideal for use in most laser applications.
What's in the box?
1 x Laser Safety Glasses
Creates a variable resistance that you can change by turning the knob
Specifications
- Single turn 5K
- Linear
- Carbon
- PCB type
- 5mm pitch pin
- Spline shaft
- 17mm diameter
- 0.2W
- Shaft length 10mm
- Shaft diameter 6mm
What's in the box?
1 x Potentiometer
Resources
Python Library
Definition, Types, And Working Principle
2x16 Character LCD is most popular display component for small controller like Arduino, but most of these LCD uses parallel interface. In most of the case, you will need 10 pins to control it or to display message on it. 8-pin are for the data, Enable and Latch pin for signal control. Minimum, you will need 6-pin for 4-bit mode interface. Still a lot of pins being used up :(
This I2C module for LCD will help you save all those precious pins. This module will only need 2 GPIO pins (specifically I2C pins) to send message to Character LCD.
This module uses an I2C communication interface. Including the I2C pins: SCL and SDA, it only require two more pins for power, VCC and GND. It saves 4 to 8 pins on Arduino or any other controller. The pins are breakout into standard right angle header (2.54mm spacing), you can connect with female jumper wires directly.
It comes with potentiometer for LCD contrast adjustment, and configurable I2C Address through A0, A1 and A2 pads. Anyway, the default address is 0x3F or 0x27. There is also a mini jumper to activate or deactivate the backlight.
- I2C connector: VCC, GND, SCL, SDA
- Compatible with Arduino/Genuino UNO, Leonardo, Mega, 101 (Intel Curie), Micro, Nano, Mini
- I2C Address:0x27 or 0x3F
- Supply voltage: 5V
- Interface:I2C/TWI x1,Gadgeteer interface x2
- Adjustable contrast via potentiometer
- Size:82x35x18 mm (3.2x1.4x0.7 in)
What's in the box?
1 x I2C Module for Character LCD
- Solid and durable.
- Ensures high-amp connection.
- Low resistance for high current capacity.
- Superior technology suited to today's high power applications.
- Ergonomically designed and easy to grip.
- Easy to un-solder and reuse.
- Used in RC battery and motor projects
Specifications
- Model: XT60
- Color: Yellow (as picture)
- Size: Approx. 23mm x 16mm
- Material: Copper PA66
1 x pair XT60 Bullet Connector Plugs(1 x Male 1 x Female)
Features
- The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
- This shield allows you to control upto 4 stepper motors
- Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
- Arduino compatible
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Supports PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- Supports Coolant enable
- Supports removable A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Uses removable A4988 or DRV8825 compatible stepping driver.
What's in the box?
1 x CNC shield
Resources
After installing the official IDE software please copy the 3 folders in the update folder to the following path:
C:\Users\Administrator\Documents\Arduino
Restart the software
Select the development board model
[Tools] -> [Board] -> WAVGAT UNO R3
Select COM port
[Tools] -> [Serial Port] -> Select the corresponding COM port
You can now use the development board
Download information: https://drive.google.com/open?id=10gwrG9uTDwaEO-7EudsmBkfgdcyrcABI
As micro:bit is gaining traction in this region, powering it is a must :)
If you are new to micro:bit, it is a powerful embedded platform or microcontroller board with easy to get started features, even easier than Arduino. It can be powered by USB micro B when loading the program, or you can use 2 x AAA batteries. So here comes the battery holder for this microcontroller.
This is a 2 x AAA battery holder for micro:bit with cover and ON/OFF slide switch. Neat!
Note: Battery & micro:bit is not included.
Features
- Terminated with 2-way JST connector, match with battery input on
- micro:bit
- Holder for 2 x AAA batteries
- ON/OFF slide switch
- Comes with cover
What's in the box?
1 x Battery Holder with On/Off Switch
Need batteries? You will find our battery selection here
In order to properly seat your Bowden tube, it is key to have a clean, square end. Without this, you risk oozing, or worse, clogging in the hot end. This super-sharp tubing cutter is the perfect tool for obtaining a clean, square cut in your tubing, every time.
Features a stainless steel blade and switch button. The housing is made from tough durable plastic. Can also be used to cut filament. But do not use as a wire cutter or you will dull the blade.
Package includes:
1 x Tube Cutter
Specifications
- Material: Copper plastic.
- Laser shape: dot.
- Outer diameter: 6 mm.
- Wavelength: 650nm.
- Working voltage: 3V.
- Total length: 9cm/3.54inch
- Wavelength: 650nm
- Operating Current: less than 20 mA
- Output Power: 5mW
- Housing material: High quality Copper
- Dimensions: 6.5 x 18mm
- Working temperature: -10 degree-40 degree
- Lens and housing: Plastic
- Wire connection: Red wire connect to Positive, Blue wire connect to Negative
What's in the box?
1 x 3V 650nm 5mW Red Dot Diode Laser Heads
Parameters
- Voltage input range: DC0-25V
- Voltage detection range: DC0.02445V-25V
- Voltage analog resolution: 0.00489V
Wiring the DC input connector
- the positive terminal connected to VCC,
- the negative connected to GND
- Output interface:
- "+" is 5V or 3.3V
- "-" then GND
- "s" Arduino connected to the AD pin
What's in the box?
1 x Voltage detection Module
Resources
- Raspberry Pi https://kookye.com/2017/06/01/design-a-voltmeter-with-the-raspberry-pi-board-and-voltage-sensor/
- Interfacing Voltage Sensor with Arduino - Measure up to 25V using Arduino, tutorial by Ravi in Electronics Hub
- Arduino 25V Voltage Sensor Module User Manual, by Henry's Bench
- Arduino Voltage Sensor 0-25V, by Superfish1000 in Instructables
The four LEDs on the breakout board are there to illuminate the subject with an even light source, making measurement more reliable.
You can use the TCS230 where you need to take action based on the color of an object. The device does react to infrared so may need an infrared filter or use the device in an enclosed space.
Features
- Chip: TCS230
- Input voltage: DC 3V-5V
- Output frequency voltage: 0 ~ 5V
- Use bright white LED lights
- Can be connected directly with Microcontroller
- Static detection of the measured object color
- Best detection distance: 10mm
What's in the box?
1 x colour recognition sensor
Specifications
- Interface : USB Type C Female to USB Type C Male
- Current : 3A
- Length : 270mm approx
- Weight : 34g approx
- Use for : Raspberry Pi 4
- With ON/OFF switch button , so that you can power on and off the Raspberry Pi conveniently.
- Colour: black
What's in the box ?
1 x USB Type C Power Cable with switch
Raspberry pi 40 pin male to female flat ribbon cable specifically designed to fit directly onto the GPIO Headers pins of the Raspberry Pi on one side and a HAT on the other.
Please note: Pi400 is not included
- 40 pin
- male to female
- GPIO Header connector
- 10cm long
What's in the box?
1 x male to female ribbon Cable
This is 20cm universal 4 Pin Buckled Cable with one end terminated with Grove JST connector, while the other end is four female header terminated wires. Color coded accordingly.
Specifications
- Suitable for connection from Grove to none Grove interface
- Grove Standard JST connector to 4 female header terminated wires
- Length 20 cm, end to end
What's in the box ?
1 x 4 Pin Buckled to Female Cable
By using the 3D pen can actually help kids developing their artistic skills, spatial thinking, and can be a great creative outlet that engages their minds as they create. Besides, this 3D printing pen has a stable performance. It is more stable, safe and reassuring. Let your child fall in love with 3D printing.
Specifications
- Electrical Parameter: 12VDC 2A
- Comes with UK Plug, Universal (AC voltage and frequency) Adapter
- Can be used everywhere
- 3D printer for hand use
- Compatible with ABS and PLA filaments
- Diameter of filaments: 1.75mm
- Nozzle diameter: 0.7mm
- Heating Temperature:
- 160ºC - 210ºC (PLA)
- 210ºC - 235ºC (ABS)
- LCD for display filament type and temperature
- Adjustable filament feeding speed
- Ergonomic design, lightweight design, easy to operate
- Dimensions: 184mm x 31mm x 46mm
What's in the box ?
1 x 3D Printing Pen with PLA filament - Blu
1 x 3D Printing Pen stand
1 x UK Plug 12V 2A AdapterPLA
1 x Packet filament (3 random colors, 3 meters in total)
1 x User Manual/Operation Instruction
Resources
Want to print a spool holder that clips onto your 3D pen?
Check out Thingiverse
This device allows you to store and use lengths of 1.75mm filament for a 3D pen. The unique mini spool is designed to prevent the filament from unraveling under its own spring tension. The parts can be welded together with your 3D pen.
Check this link out to see what some people come up with :
3D printing pen
PLA plastic is a biodegradable thermoplastic, made from renewable resources like sugarcane or corn starch or soybeans. When it melts, there is no smell, so it is very comfortable to use in the home or classroom.
Specifications
- High strength, good toughness
- Density is small, when printing larger volume model lighter, save money
- Cost-effective as it can be processed in a wide range temperature
- PLA has a low shrinkage rate, even print larger models perform well
- To be applied to a variety of 3D printer, Makerbot, UP plus, Mendel, Prusa, series, etc
- Environmental friendly PLA material, no bubble exited, accurate filament diameter
- Non-toxic and no smell
Features
- Colour: 3 Colours (Random)
- Quantity: 3
- Material: PLA
- PLA: 190 - 220° C
- Diameter:1.75mm
- Length: 9 meters (3 meters each color)
- Usage: 3D Printing Pen
- Section Shape: Round
What's in the box?
1 x 3 Colors 1.75mm PLA Filaments for 3D Pen-9 Meters
Resources
Want to print a spool holder that clips onto your 3D pen?
Check out Thingiverse - This device allows you to store and use lengths of 1.75mm filament for a 3D pen. The unique mini spool is designed to prevent the filament from unraveling under its own spring tension. The parts can be welded together with your 3D pen.
Besides, you can use this ethernet cable with Raspberry Pi! We have tested this ethernet cable with Raspberry Pi 4B and the result is incredible. Just plug-in and you can use it.
Here is the iperf3 test result with Raspberry Pi 4B as server and another Raspberry Pi 4B as client. It reaches 940mbps, and that if what you expect for Gigabit Ethernet. (WiFi is disabled for both the RPi 4B)
Features
- Has better performance
- Designed for home and office network
- Backwards compatible with CAT-5e and CAT-5 environment
- RJ45 connectors at both ends of the cable
- Compatible on most devices. e.g: Computer, router, etc
Specifications
- Type: CAT6 Flat Gigabit Ethernet cable
- Data speed: Up to 1 Gbps
- Transmission frequencies: Up to 250 MHz
- Colour: Skyblue
- Length: 2 meters
What's in the box?
1 x RJ45 CAT6 Flat LAN Cable 2m
As the new Raspberry Pi 400 keyboard computer does not come with a 3.5mm Audio Barrel for speaker output, this USB powered, and signal is the perfect speaker for it. And we have tested it with Raspberry Pi 400, it works like expected. No driver is needed, plug and use!
Note: If you're using the speaker with your Raspberry Pi, be sure to change the audio device to USB2.0 Device and change the output to Digital Stereo Output. Else, you will not be able to control the volume.
Features and specifications
- They are small and compact, so they can be brought anywhere.
- Powered by a single USB cable, have NO volume control knob, easy to use.
- Anti-interference and stereo sound.
- Crystal-clear treble.
- Space-saving design, they can be conveniently placed next to your PC monitors without compromising on valuable desk space.
- Built-in 2 speakers, balance and enhance the sound of your laptop, notebook, computer, PC, tablets, good for work, music, movies, games, etc.
- Acoustic quality stereo sound, let your room filled with music, movies, or computer games.
- No driver is needed for Windows, Linux and macOS, just plug and play!
- Great for
- Enhance any media experience while at home, office, kitchen, basement, or on the go.
- Upgrade to your computer's weakened or faint internal speakers. Perfect USB Speakers for Windows PCs, Desktop Computer, Laptop.
- Daily listening, static listening at home or office.
- Material: Plastic
- Output Power: 3W*2
- Channel: 2.0
- Frequency Response Range: 25Hz-20KHz
- Separation: ≥40dB
- Power Supply: USB 5V
- SNR: ≥80dB
- Voltage: 5V
- Connectivity: USB
- Number of speakers: 2
- USB Cable Length: 47 inches
- Connection radius: direct connection
What's in the box?
1 x 6W Stereo USB Power and Signal Speaker-BlackThis is the jumper wires that I have been dreaming of :) This is a box full of color-coded assortment of small jumper wires, great for prototyping. And it is pre-cut, stripped and bent at both ends with the standard breadboard spacing, perfect for classroom and when you do experiment with breadboard.
The best is it comes in a proper plastic box. There are 140 wires in total with different lengths. So get ready for it.
Features
- Wide application: designed to work well with any breadboards or anywhere jumper wires are needed, perfect for breadboard projects.
- Easy to use: all the colored jumper wires are pre-stripped and preformed right-angled, easy to insert into breadboard.
- Complete specification: this kit includes 14 different lengths of jumper wires which can satisfy all your need.
- Storage box: come with a free plastic box, keep your jumper wire kit organized, convenient for store and fetch.
- These leads are flexible, durable and easy to connect and disconnect, ideal for prototyping use.
Specifications
- Material: Plastic Metal.
- Quantity: 140 pcs.
- Colour: Rainbow color with red, yellow, green, white, blue, orange and grey.
- Wire Length: 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, 125mm (10pcs of each length).
What's in the box ?
140 x Jumper Wires
1 x Storage Box
You might also need....
Breadboard not included - Click HERE to get yours !