Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
Motor Control Shield is capable of driving 4 DC motors or 2 stepping motors at one time.
R126.90  Inc VAT
USB cable included
R179.90  Inc VAT
R196.90  Inc VAT
WS Motor Control Shield for Arduino (WS Arduino Motor Control Shield)
Description

Motor Control Shield is capable of driving 4 DC motors or 2 stepping motors at one time.

Features
  • Configurable motor power supply via onboard jumper
    • when using 5V motor power supply : drives four 5V DC motors at one time
    • when using adjustable motor power supply : drives two 1.25V-6.45V DC motors at one time (9V external power supply is required)
  • Onboard dual H-bridge driver L293D x 2
    • each L293D can drive 2 DC motors or 1 stepping motor at one time
    • totally 4 channel H-bridge, with 600mA output current (peak 1.2A) per single bridge
    • ESD protection
What's on Board
  1. External power supply jack
  2. Power input/output pinheader
  3. Stepping motor interface
  4. DC motor interface
  5. M_PWR configuration : connects M_PWR (motor power) to 5V or ADJ
  6. Power selection switch
  7. Power indicator
  8. AMS1117-ADJ : onboard linear regulator with adjustable output
  9. Adjustable potentiometer : for adjusting the output voltage of ADJ (adjustable motor power)
  10. L293D : dual H-bridge driver
  11. LM2596-5.0 : onboard linear switching regulator with 5V output

Note : when in operation, it's normal that the onboard motor drivers and regulators generate lots of heat.

Development resources: demo codes, schematic, datasheets, etc.
www.waveshare.com/Motor_Control_Shield

Motor Control Shield is capable of driving 4 DC motors or 2 stepping motors at one time.
R126.90  Inc VAT
ATmega328P Arduino Compatible Nano V3 Improved Version (Arduino nano)
This Arduino Nano comes with the old bootloader
Description:


ATmega328 is commonly used in many projects and autonomous systems where a simple, low-powered, low-cost micro-controller is needed.
The Arduino Compatible Nano V3 development board is a microcontroller board based on the Arduino Nano

Specifications:

  • Microcontroller Atmel ATmega328
  • Operating Voltage (logic level): 5V
  • Input Voltage (recommended): 7V ~ 12V
  • Input Voltage (limits): 6V ~ 20 V
  • Digital I/O Pins: 14 (of which 6 provide PWM output)
  • Analog Input Pins: 8
  • DC Current per I/O Pin: 40mA
  • Flash Memory: 32KB (ATmega328) (of which 2 KB used by bootloader)
  • SRAM: 2KB (ATmega328)
  • EEPROM: 1KB (ATmega328)
  • Clock Speed: 16MHz

Package includes:

1 x Arduino Compatible Improved Version Nano V3.0 with headers pre-soldered
1 x USB cable

Resources:

Getting started with Arduino products
USB cable included
R179.90  Inc VAT
Transparent Acrylic Case For Arduino MEGA2560 R3 Module Board(Arduino is not included) (Mega Acrylic case)
Description:

This product is protective case of Arduino MEGA2560 R3. It provides easy connection to other components. It is made by high grade acrylic providing protection for your Arduino

Feature:

Name: Arduino MEGA2560 R3 DIY acrylic case
Dimensions: 118 x 72 x 18mm
Weight: 72g
Material: A level acrylic
For Arduino MEGA2560 R3 Development Board only

Please Note:
Arduino Mega is not included.
Don't forget to remove the protective film from the acrylic parts.

Package includes:

1 x Transparent Acrylic case
R44.90  Inc VAT
cnc shield v3 engraving machine 3D Printer board 4pcs A4988 driver expansion board for Arduino UNO R3 with USB cable (uno cnc control kit)
Description:

Perfect for engravers, laser cutters, CNC machines and 3D printers. This shield simply sticks on top of your Arduino board and can control up to 4 stepper motors.

Features:
CNC Shield Board:
 
Latest CNC Shield Version 3.0 for Arduino.
GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals)
PWM Spindle and direction pins
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a  full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Uses removable A4988 or DRV8825 compatible stepper drivers
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to  1/32 micro-stepping )
Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
Please note that this is an unassembled kit and Basic soldering skills are needed.
 
A4988 Stepper Motor Driver:
 
A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product.
Low RDS (On) Output
Automatic current decay mode  detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full,  1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).

Step 1: Download the GRBL HEX file https://github.com/gnea/grbl/releases/tag/v1.1f.20170801
Step 2: Download XLoader https://github.com/xinabox/xLoader
Step 3: Open XLoader and Load the HEX File downloaded in Step 1.
Step 4: Select the current Board - Uno(ATmega328) and COM port.
Step 5: Press Upload.
DONE!


Package Includes:
1 X cnc shield v3
4 X A4988
4 X Heatsink
1 X UNO R3
1 X USB cable
R419.90  Inc VAT
Yellow blue double colour 128X64 OLED LCD Display Module For Arduino 0.96" I2C IIC SPI Serial (OLED display)
Description

OLED displays driven by SSD1306 driver IC. SSD1306 is a CMOS OLED driver with controller for OLED dot-matrix graphic display system.
This is a popular OLED display with Portable and wearable devices becoming the new trends. 

Specifications:

Driver: SSD1306
Interface type: IIC interface
Pin definition: GND, VCC, SCL, SDA
        1:GND(OLED power supply)
         2:VCC (OLED 3.3~5V)
         3:SCL(OLED IIC Clock line)
         4:SDA(OLED IIC Cable)


What's in the box?:

1 x OLED display

Resources:

We used these instructions to get it working on Pi: https://circuitdigest.com/microcontroller-projects/ssd1306-oled-display-with-raspberry-pi
R64.90  Inc VAT
LCD module 3.5 inch TFT LCD display for Arduino UNO R3 Board and supports mega 2560 R3 (Arduino LCD display 3.5inch)
PLEASE NOTE: Arduino board and USB cable are not included

LCD module 3.5 inch TFT LCD screen 3.5 " for Arduino UNO R3 Board and support mega 2560 R3



Watch a video on this item at https://www.youtube.com/watch?v=PAPW97X6IRM
 


Package Includes:
 
 1 x 3.5 inch TFT LCD


Resources:

We have found the best Libary to use to run this display is: MCUFRIEND_kbv Library for Uno 2.4, 2.8, 3.5, 3.6, 3.95 inch mcufriend Shields
You can find out more: https://github.com/prenticedavid/MCUFRIEND_kbv
Open Arduino IDE
Click on Sketch -> Include library -> Manage Libraries -> and search for MCUFRIEND
Once installed, you can test your display using the provided examples
LCD Not Touchscreen
R369.90  Inc VAT
Avoidance tracking Smart Robot Car Chassis Kit Speed Encoder Battery Box 2WD Ultrasonic module For Arduino kit (Aduino robot car)
Please Note: Some drilling will be required. You might need to add a few standoffs and screws to build it the way you want it.
Description:

This complete robot car kit includes the arduino as well. Just add batteries and code. Great for beginners to learn how to code using sensors and motion on the Arduino boards

Pdf manual available at http://www.cs.columbia.edu/~sedwards/presentations/robot-car-instructions.pdf 
Get more details at https://create.arduino.cc/projecthub/hda-robotics/project-1-2wd-obstacle-avoiding-robot-390ef8

Package Includes: 
  • Car chassis x 1 
  • Car Wheels x 2 
  • DC Gear Motor x 2 
  • 20 line gun code disk x 2 
  • Fasteners (high intensity black acrylic) x 4 
  • Caster x 1 
  • Four battery box x 1 
  • Quality Rocker Switch x 1 
  • Assembly drawing x 1
  • Several screws and nuts
  • V5 shield x 1
  • UNO R3 x 1
  • SG90 x 1
  • FPV x 1
  • L298N x 1
R599.90  Inc VAT
camera module OV7670 Supports VGA CIF auto exposure control display active size 640X480 for Arduino (Arduino camera)
Description

OV7670 image sensor, small size, low operating voltage, and provides all the features of the single-chip VGA camera and image processor. Through the SCCB bus control, you can output the entire frame, sub-sampled, take the window way affect the data resolution of 8 bits. VGA image of the product is up to 30 frames / sec. Users can fully control the image quality, data format and transmission mode. The process of image processing functions including gamma curves, white balance, saturation, chroma, and so can be programmed through the SCCB interface. OmmiVision image sensor applications unique sensor technology to improve image quality by reducing or eliminating the optical or electronic defect, such as fixed pattern noise, tail-blooming, clear and stable color image.


    • Low voltage suitable for embedded applications
    • Standard SCCB interface compatible with I2C interface
    • RawRGB to RGB (GRB4: 2:2, RGB565/555/444), YUV (4:2:2) and YCbCr (4:2:2)output format
    • support VGA, CIF, and from CIF to 40x30 the size
    • VarioPixel subsampling way eliminate light stripes, automatic black level calibration image quality control including color saturation, hue, gamma, sharpness ANTI_BLOOM
    • ISP has eliminate noise and dead pixel compensation function
    • Support image scaling
    • The lens is the loss of light compensation
    • 50/60Hz detection
    • The saturation automatically adjust ( UV adjustment)
    • edge enhancement automatically adjust
    • Noise Reduction automatically adjust
Key parameters
  • photosensitive array 640X480
  • O voltage 2.5V to 3.0V ( internal LDO to core supplies ) the
  • power operation 60mW/15fpsVGAYUV
  • Sleep < 20 μ A
  • temperature operation from 0 ° C to 50 ° C
  • ( 8 -bit) output format ? YUV/YCbCr4 RGB565/555/444 GRB4: 2:2: 2:2 Raw RGB Data
  • Optical size of 1/6 "
  • field of view angle of 25 °
  • maximum Zhen rate 30fps VGA
  • Sensitivity 1.3V / (Lux-sec)
  • signal to noise ratio of 46 dB
  • dynamic range of 52 dB
  • browsing mode progressive
  • electronic exposure
  • area of 3.6 μ mx 3.6 μ m
  • dark current 12 mV / s at 60 ° C


Package Includes:

1 x camera board

Resources:

How to Use OV7670 Camera Module with Arduino
R59.90  Inc VAT
LCD Keypad Shield LCD1602 LCD 1602 Module Display For Arduino ATMEGA328 ATMEGA2560 raspberry pi UNO blue screen (buttons blue backlight)
Description
  •     This is a basic 16 character by 2 line display.   
  •     Utilizes the extremely common HD44780 parallel interface chipset.   
  •     Interface code is freely available.   
  •     Blue Backlight with white words.   
  •     uses 4 Bit Arduin LCD Library.   
  •     Size:8cm x 5.9cm - 3.15inch x 2.32inch   


Package Content:

1 X Keypad Shield 1602 LCD

DFRobot WIKI
R87.90  Inc VAT
2 Pcs LilyPad Button Connect Sensor Board Module for Arduino Power DIY KIT Momentary Push Button Electronic PCB Board Module (wearable buttons(2))
Description:

We designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!

Package:

2 x LilyPad Button Board module for ArduinoWe designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
 
Dimensions:

8mm x 16mm
Thin 0.8mm PCB
 
Package Includes:

2 x LilyPad Button Board module for Arduino

Getting started with Lilypad button sensor board
R11.90  Inc VAT
USB A to USB B Arduino Uno/Mega USB cable 30cm (uno/mega cable 30cm)
Description:

Use it to connect Arduino Uno, Arduino Mega 2560, Arduino 101 or any board with the USB female A port of your computer. This is a standard issue USB 2.0 cable. the kind that's usually used for printers.

Connect your USB printer, scanner and more to your computer. Transmits data at high speeds with error-free, high-performance transmission.



Specifications:

  • Arduino Uno/Mega USB cable
  • 30cm
  • USB A to USB B
  • Blue


What's in the box?

1 x USB A to USB B cable
R29.90  Inc VAT
WAVGAT cnc shield v3 engraving machine / 3D Printer / A4988 driver expansion board for Arduino (cnc shield only)
Description:

The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO, and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. 



Features:

  • The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
  • This shield allows you to control upto 4 stepper motors
  • Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
  • Arduino compatible
  • Latest Arduino CNC Shield Version 3.10
  • GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
  • Supports PWM Spindle and direction pins
  • 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
  • Supports Coolant enable
  • Supports removable A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
  • Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
  • Compact design.
  • Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
  • Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
  • Uses removable A4988 or DRV8825 compatible stepping driver.


What's in the box?

1 x CNC shield

Resources:

After installing the official IDE software please copy the 3 folders in the update folder to the following path:

C:\Users\Administrator\Documents\Arduino

Restart the software
Select the development board model
[Tools] -> [Board] -> WAVGAT UNO R3

Select COM port
[Tools] -> [Serial Port] -> Select the corresponding COM port

You can now use the development board

Download information:  https://drive.google.com/open?id=10gwrG9uTDwaEO-7EudsmBkfgdcyrcABI
R68.90  Inc VAT
Infrared IR Wireless Remote Control Module DIY Kit HX1838 For Arduino (IR remote control Arduino)
Description:

Latest infrared wireless remote control kit consists of Mini Slim 38KHz IR remote control and infrared receiver modules, Mini Slim infrared remote control with 17 function keys, working distances of up to 8 meters, ideal for a variety of devices. IR receiver module can receive standard 38KHz modulation remote control signal, through programming, you can achieve remote control signal decoding operation, which can produce a variety of remote control robots and interactive projects.
 
Features:

    1 Transmission Distance: 8m above (specific and surroundings, the receiver sensitivity and other factors)
    2 Effective angle: 60 degrees
    3 Sticking Material: 0.125mmPET, the effective life of 20,000 times.
    4. Stable quality, cost-effective
    5 quiescent current 3-5uA, dynamic current 3-5mA.

 

 

#include <IRremote.h>

int RECV_PIN = 11;

IRrecv irrecv(RECV_PIN);

decode_results results;

void setup()
{
  Serial.begin(9600);
  irrecv.enableIRIn(); // Start the receiver
}

void loop() {
  if (irrecv.decode(&results)) {
    Serial.println(results.value, HEX);
    irrecv.resume(); // Receive the next value
  }
}
R29.90  Inc VAT
Get Started with Arduino (book start Arduino)
Description:

Whether you want to build robots, smart devices, or any other electronically controlled projects, this is the book you need. We take you through how to program and connect an Arduino microcontroller board, then explore some great projects to make with it.

Specifications:
  • Build a four-legged walking robot
  • Create a Tetris-inspired clock
  • Grow your own veg with hydroponics
  • Make music with a DIY synthesizer
  • And much more!
R196.90  Inc VAT
GPS Serial Module APM2.5 Flight Control GT-U7 with Ceramic Antenna (arduino GPS board)
Description:

Its high sensitivity, small static drift, low power consumption and compact size makes it suitable for applications in vehicles, handheld devices such as PDAs, vehicle monitoring, mobile phones, video cameras, and other mobile positioning systems.
 
Features:
 
- Operating frequency: L1 (1575.42 /- 10MHz)
- Operating voltage: 3.3 - 5.2V
- Operating current: normal mode is 50mA, the power-saving mode is 30mA
- Communication interface: TTL serial port, micro USB interface (can be connected to a computer to debug)
- Serial port baud rate: 9600bps
- Communication format: 8N1
- Interface logic voltage: 3.3V or 5V
- External antenna interface: IPX. 

What's in the box?

1 x GT-7U GPS module
1 x Control board
1 x Header

More info available here



R399.90  Inc VAT
Arduino starter kit - UNO compatible (Arduino UNO kit)
Description:

This kit is a great way to start your arduino learning experience and includes the following:


You might also like our handy GET STARTED WITH ARDUINO book.

Need to make your UNO project more mobile? Have a look at our battery solutions:


We do also stock enclosures for the Arduino
R409.61  Inc VAT
PikaBot - Maker UNO Smart Car Kit (CT uno car kit)
Description:

Everyone loves mobile robot! With PikaBot, you get to learn electronics, microcontroller, sensors, motors & coding, while having fun!

https://youtu.be/X6qFEwy2X2w



New to Mobile Robot & Coding?

Don't worry! This kit comes with a booklet covering all the hands-on lessons you need to get started. Every step is explained clearly with the help of images. We make sure that the common issues when building and coding the Arduino mobile robot are properly addressed in this booklet. Besides it comes with fun facts to feed the curious minds too.



No Soldering! Just Jumper Wires

There is no soldering involved in order for more young makers to take part in the building process. To make things even simpler, the detailed schematic diagram and mounting location of the parts are printed inside the box. Hence you can build and connect with greater confidence as you embark on this digital making journey.



This mobile robot kit is based on Maker UNO (Arduino Uno compatible).



Box = Mobile Robot Base

We designed the packaging box of PikaBot to be reusable. Not only that it's used for packing the complete set of components needed for the project, it serves as the robot base and cover of your PikaBot mobile robot too.



Line Following & Obstacle Avoidance

What can your PikaBot do? It can follow line, simple yet practical navigation that is widely used in AGV (Automated Guided Vehicle) and many robot competition. The kit comes with a pair of infrared sensors which you can calibrate & program to recognize black and white surfaces. PikaBot also includes an ultrasonic distance sensor so it can detect obstacles in front of it.



mBlock Graphical Programming Interface

Besides using the Arduino IDE as taught in our user guide booklet, you can also program PikaBot with mBlock block-based programmming interface. Check out this tutorial to learn more.


https://youtu.be/S-xbk-PoiWY

With the beginner-friendly Maker UNO as the controller, everyone can build and program this mobile robot. We have also included

  • Dual-channel motor driver - Maker Drive
  • Two "TT" brush motor with pre-solder wires
  • 4 x AA battery to power the controller and motor 
  • Of course, it comes with two IR Line Tracking Module for line following
  • An Ultrasonic Distance Sensor for obstacle avoidance
  • Accessories for the smart car to work :)
  • Everything is packed in a nicely designed paper box which will be utilized as the base of the mobile robot too



To make life even easier, we have prepared:

  • A printed copy of Step by Step Guide for you to build this kit (Softcopy here)
  • Sample code for line following, obstacle avoidance and melody in Arduino Sketch in Github (coming soon)
  • Video to assemble the robot is in the making, check it out


Line Following Track for line following.



Features:

  • Mobile Robot Kit
  • Do It Yourself (DIY) mobile robot kit
  • No soldering needed, only requires to connect jumper wires :)
  • Controller: Maker UNO
  • Motor Driver: Maker Drive dual-channel DC brush motor driver
  • Driven by two TT motor with pre-solder wires
  • Power both controller and motor with 4 x AA battery, with battery holder too
  • Comes with IR Line Sensor module, for line following
  • Open-source example code, free to modify and learn coding
  • Panel mount rocker switch as power activation switch
  • Panel mount push button as a start button
  • The paper box is creatively designed as the container and also body for mobile robot.
  • Everything needed is packed in this kit!
  • Box Dimension: 127mm x 55mm x 19mm (not including motor shafts and wheels)

 

Packing List:

  • 1 x Maker UNO (Simplifying Arduino for Education)
  • 1 x Maker Drive: Dual H-Bridge Motor Driver for Beginner
  • 2 x 3 - 6VDC Dual Axis TT Gear Motor (with pre-solder wires)
  • 2 x Rubber Wheel for TT Gear Motor (63mm x 15mm)
  • 2 x IR Line Tracking Module
  • 1 x HC-SR04 Ultrasonic Ranging Module
  • 1 x 4xAA Batteries
  • 1 x 4xAA battery holder
  • 1 x Breadboard Mini (35mmx42mm) - White
  • 1 x 40 ways Male to Female Jumper Wire
  • 1 x 40 ways Male to Male Jumper Wire
  • 1 x USB Micro B cable
  • 1 x mBot N20 Vacuum Steel Ball Castor
  • 1 x Tiny Phillips Screwdriver - 85mm
  • 4 x Bolt M3x25mm
  • 4 x M3 Nut
  • 1 x CH2 Quick Wiring Terminal Press Type
  • 1 x Rocker Switch with wires
  • 1 x Push Button with wires
  • 14 x Plastic Rivet (M3)
  • 2 x Plastic Rivet (M4)
  • 1 x PikaBot Track
  • 1 x PikaBot Booklet - A step-by-step guide to build & program PikaBot.
  • 1 x PikaBot Paper Box
     

Documents:

 

Telegram Stickers!

    Last but not least, we've designed some expressive PikaBot stickers for Telegram messenger for all you PikaBot lovers! If you are a Telegram user, grab the sticker pack here: https://t.me/addstickers/cytron_pikabot. Have fun!

    R499.90  Inc VAT
    Maker UNO Edu Kit (Arduino Compatible) (CT uno edu kit)
    The Typical Problem Faced By Teachers In Conducting Arduino Classes

    1. Most of the students do not have basic knowledge in electronics.



    2. They do not understand the circuit diagram at the beginning of the Arduino lesson. They will spend a substantial amount of time just to connect the wires and troubleshoot the connections.

    3. It's a mess after every class. The teacher has to sort and make sure nothing is missing. What a tedious job and a waste of time! 

    Students can skip the hassle of constructing the basic electronic circuit which is boring and time consuming. Although it is equally important for them to learn about basic electronics, it can always come later after they have experienced how easy it is to create awesome project. Start with fun and excitement. Start coding right away and see your board lights up and plays melody with the press of a button. 



    With the conventional Arduino boards, students also face another common problem - difficulty in troubleshooting their circuit. This is because when it doesn't work, we do not know whether the problem is due to wire connection or coding.



    With Maker UNO, the problem is solved! Not only do the onboard LEDs work as outputs, they can also act as indicators, clearly showing what's happening on that pin. When the pin is used as input, you can clearly see whether the signal is received by just looking at changes on the LEDs. 



    Additional Features

     

    One of the brilliant features of the official Arduino Uno is the label printed on its pin headers. It saves us a lot of time when we want to connect the I/O pins to the external circuit. So, we include a set of these label stickers for pin headers in each of the Maker UNO! (Please note that you need to peel off the stickers and stick them on your Maker UNO by yourself)



    Students always get their boards mixed up. With Maker UNO, you can write your name on the board. Problem solved!



    Maker UNO uses the common Micro USB cable which is basically everywhere.



    Don't throw your box away! There is a small opening on the box for you to plug the USB cable so that you can keep your Maker UNO safely in the original box, no additional casing required.



    Specifications

     

    Maker UNO is fully compatible with Arduino. You can share the same library and code. We put in 12x LEDs, 1x piezo buzzer and 1x programmable button on the Maker UNO. We have removed the DC jack power input socket as most of the boards used in classes are powered using USB. We have also replaced the ATmega16u2 with CH340 to bring down the cost.





    Documents:

    Tutorials:


    Related links:


     

     

    R319.90  Inc VAT
    Resolute Robotics Beginner Stream - 4 In 1 Engineering And Computer Sciences Robotics Kit (resolute beginner kit)

    Description

    This package offers a year-long robotics course. The course commences with the fundamentals of robotics and coding as well as the importance of simulation.


     

    Once the fundamentals are covered, students take part in a practical project where they’re required to build an automated hand sanitiser. An infra-red sensor will detect a hand and the system will discharge a small amount of soap or sanitiser. The second project in the course is a practical project called the Home Automation System. In this project, students will demonstrate the practical application of servo motors, temperature sensors, infrared sensors, fans, buzzers, lighting and a security system feature in a home automation system.

     

    After completing these two practical projects, the course will introduce students to the world's most popular coding language: Python. Throughout the course, students will learn how to develop several applications such as Tic Tac Toe, Hangman and Pong. They’ll also be introduced to libraries such as Turtle to help grow their understanding of how programming works and how code is read by the computer.

    OVERVIEW:

     

    The Resolute Beginner’s Kit is a great way to get started in the world of robotics and coding. It includes all the components required to build projects like the Automated Hand Sanitiser, the Home Automation System and much more. There are also fun challenges to test the students’ understanding of what they’ve learned. This kit gives you access to an online platform where step-by-step video instructions are provided to help you learn and build with ease.





    Additional Requirements:

    • Internet Connection
    • Laptop, PC or Mac
      • 1.4 GHz CPU or higher
      • Minimum of 10GB free storage on your device
    • Recycled Material (such as cardboard)
    • An Interest to Learn.

     

    FEATURES:

    • Video-based learning for each project, task and concept taught in the course. 
    • Plug and play: No soldering required, build your circuit in minutes.

     

    Components:

    • Arduino Uno
    • Digital Multimeter (9V Battery Banana to crocodile cable included)
    • Mini Screwdriver Set
    • DC Motor Water Pump
    • DC / DC Buck (LM2596)
    • Analog Temperature Sensor Module
    • Brushless Fan DC 5V
    • AC Power Supply
    • Reed sensor module (with Mini Magnets)
    • Tubing
    • Breadboard x 2
    • 20cm Male-to-Female Jumper Cable x 2
    • 65pcs Male-to-Male Jumper Wires x 2
    • MG90S Metal Gear Micro Servo x 2
    • Relay (5V 1 Channel Module) x 2
    • 9V Battery Button Power Cable x 2
    • USB Extension Cable
    • Active Buzzer x 2
    • Infrared Sensor x 4
    • Push-button Pack
    • Resistor Pack
    • Variable Resistor Pack
    • LED Pack
    • RGB LED x 2
    • Phototransistor
    • Extra wires (8 core solid wire) for Breadboard use




    ADDITIONAL INFORMATION:

    https://youtu.be/rzSd97NkbEY


    R3,795.00  Inc VAT
    Advanced Stream - 4 in 1 Engineering and Computer Sciences Robotics Kit (resolute advanced kit)
    Description

    The course starts off with an introduction to the fundamentals of Arduino programming and electronic circuit theory fundamentals. Students will learn about simulation, sensors, automation and processing real-world data. They’ll get creative with a practical project like the Autonomous Line Following Car where an infrared sensor is used to detect a black line and the Arduino sends a set of instructions to the DC motors directing the car. 


     

    Students will be challenged further by applying their programming and engineering skills to design and build an access control system. They’ll create their own security system by programming an RFID tag to automatically open a door, granting access to personnel only. Students will also learn to master the world's most popular coding language, Python. They’ll learn essential game development concepts such as controlling player and non-player sprites, implementing in-game physics and collision, object-oriented game design, randomization and artificial intelligence.



    OVERVIEW:

     

    The Resolute Advanced Kit is a great way for students to continue their robotics journey. It includes all the components needed to build a range of projects such as the Autonomous Line Following Car and Access Control using RFID tags. With a little bit of creativity, these components can be used to build hundreds of other projects. This kit gives you access to an online platform where step-by-step video instructions are given to help you learn and build with ease.

     

    Additional Requirements:

    • Internet Connection
    • Laptop, PC or Mac
      • Minimum 4 GB of RAM
      • 1.4 GHz CPU or higher
      • Minimum of 10GB free storage on your device
    • Recycled Material (such as cardboard)
    • An Interest to Learn.



    FEATURES:

    • Video-based learning for each project, task and concept taught in the course. 
    • Plug and play: No soldering required, build your circuit in minutes.

     

    Components:

    • Arduino Uno x 2
    • Digital Multimeter (9V Battery Banana to crocodile cable included)
    • Mini Screwdriver Set
    • Smart Robot Car Chassis Kit
    • RFID Tag reader (MFRC-522 RC522) 
    • 2000mAh Power Bank
    • Breadboard x 2
    • 20cm Male-to-Female Jumper Cable x 2
    • 65pcs Male-to-Male Jumper Wires x 2 
    • MG90S Metal Gear Micro Servo x 3
    • Relay (5V 1 Channel Module) x 3
    • 9V Battery Button Power Cable 
    • USB Extension Cable
    • Active Buzzer 
    • Infrared Sensor x 5
    • Push-button Pack
    • Resistor Pack
    • Variable Resistor Pack
    • LED Pack
    • RGB LED
    • Phototransistor
    • Extra wires (8 core solid wire) for Breadboard use

     

    ADDITIONAL INFORMATION:

    https://youtu.be/cqVqC3JykdU


     

    R4,025.00  Inc VAT
    Per Page      21 - 40 of 56