Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
R341.97  Inc VAT
This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R241.10  Inc VAT
1.8inch colourful display module for micro:bit 160x128 (1B3 micro:bit display)

Please note: Micro:bit and USB cable not included

Overview

This is a colorful display module designed for the BBC micro:bit, 1.8inch diagonal, 160x128 pixels, capable of displaying 65K colors.

Tired of the 5x5 LED matrix? Time to get a tiny monitor for your micro:bit, this one would be the ideal choice.

Features

  • micro:bit edge connector, directly pluggable
  • Embedded driver ST7735S, supports 65K colors
  • Onboard SRAM 23LC1024, used as display cache, no more out of memory
  • SPI interface, takes up only a few IO pins
  • Backlight adjustment via PWM
  • Reserved solder pads for control interface, make it easy to connect with Arduino/Nucleo boards
  • Comes with development resources (micro:bit graphical demo/user manual, etc.)

Specifications

  • Driver: ST7735S
  • Resolution: 160x128
  • Display color: RGB, 65K colors
  • Operating voltage: 3.3V
  • Dimension: 61mm x 51.5mm

Pinouts

PINmicro:bit PINDESCRIPTION
3V33V3Power
GNDGNDGround
MISOP14SPI data master input/slave output
MOSIP15SPI data master output/slave input
SCKP13SPI clock input
LCD_CSP16LCD chip selection
RAM_CSP2SRAM chip selection
DCP12LCD data/command
RSTP8LCD reset
BLP1LCD backlight

Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/1.8inch_LCD_for_micro:bit



R186.90  Inc VAT
Raspberry Pi 7" Touchscreen Display (Official) (WH display 7 official)

The display will technically work with the Model A and Model B boards (connecting it to the DSI port on the Pi board), however the mounting holes on the back of the display will only line up with the newer board design (A+, B+, Pi2 and Pi3)

The eagerly awaited 7" Official Raspberry Pi Touchscreen Display is finally hear! Boasting a neat 800×480 display @ 60fps resolution, and 10 point capacitive touchscreen, this 7" screen for the Raspberry Pi gives users the ability to create all-in-one, integrated projects such as tablets, infotainment systems and embedded projects.

The 800x 480 display connects via an adapter board which handles power and signal conversion.Only two connections to the Pi are required; power from the Pi’s GPIO port and a ribbon cable that connects to the DSI port present on all Raspberry Pi’s. Touchscreen drivers with support for 10-finger touch and an on-screen keyboard are available on the latest Raspbian OS for full functionality without a physical keyboard or mouse.

  • Turn your Raspberry Pi into a touchscreen tablet, infotainment system, or standalone device.
  • Truly Interactive - the latest software drivers will support a virtual ‘on screen’ keyboard, so there is no need to plug in a keyboard and mouse.
  • Make your own ‘Internet of Things’ (IoT) devices including a visual display. Simply connect your Raspberry Pi, develop a Python script to interact with the display, and you’re ready to create your own home automation devices with touchscreen capability.
  • A range of educational software and programs available on the Raspberry Pi will be touch enabled, making learning and programming easier on the Raspberry Pi.
  • Raspberry Pi mounting points on the back

Technical Specification:

  • 7” Touchscreen Display.
  • Screen Dimensions: 194mm x 110mm x 20mm (including standoffs)
  • Viewable screen size: 155mm x 86mm
  • Screen Resolution 800 x 480 pixels
  • 10 finger capacitive touch.
  • Connects to the Raspberry Pi board using a ribbon cable connected to the DSI port.
  • Adapter board is used to power the display and convert the parallel signals from the display to the serial (DSI) port on the Raspberry Pi.

N.B. Will require the latest version of Raspbian OS to operate correctly.

Kit Contents:

  • 7” Touchscreen Display
  • Adapter Board
  • DSI Ribbon cable
  • 4 x stand-offs and screws (used to mount the adapter board and Raspberry Pi board to the back of the display
  • 4 x jumper wires (used to connect the power from the Adapter Board and the GPIO pins on the Pi so the 2Amp power is shared across both units)

Please Note. The Raspberry Pi Board and accessories are not included in this kit.

Installation instructions can be found at:
http://www.element14.com/community/docs/DOC-78156?ICID=rpimain-touchscreen-7inban#installI
 

R1,068.29  Inc VAT
USB Detector Current Voltage 3V-9V Tester Dual USB Dual display (2A5 USB Docter Dual)

Use the USB Charger Doctor to measure the working voltage and current output for any USB port and project. This plastic dongle plugs between a USB device, and passes the data lines through. There's a 0.05 ohm resistor in line with the power pin that is used to measure current draw. The Doctor's digital display instantly reads the numbers out for testing devices such as chargers, cables, and cell phones.

You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It displays both voltage and current readouts. It's a very handy tool for testing USB devices, checking load levels and debugging battery chargers and boost converters.

R94.90  Inc VAT
Pimoroni - Noir 7" Touchscreen Display Frame (Stand Display Black Noir)

Protect your new 7" Raspberry Pi Touchscreen with this lovely little display frame from Pimoroni! Designed with a slimline profile, it's perfect for keeping your Raspberry Pi screen upright, and at an ideal viewing angle!

Please note: Raspberry Pi Touchscreen and Raspberry Pi are not included

Pimoroni's Touchscreen Display Frame Features:

  • Slim profile made up of only 3 layers keeps the screen protected
  • 2 Legs hold the screen at an ideal viewing angle
  • Provides support and protection to the back of the screen
  • All Raspberry Pi Ports accessible
  • Leaves touchscreen free for touching
  • No tools required for assembly
R159.90  Inc VAT
Discontinued: Raspberry Pi 7" Touchscreen Display Case - Black (AW C5 display case glove Black)

Protect your new 7" Raspberry Pi Touchscreen with this premium black case! Designed to house a Raspberry Pi B+/2/3 and the official 7" LCD Touchscreen, it leaves the touchscreen front and Raspberry Pi ports fully available, but encloses the unit completely.

It's also fitted with two non-slip rubber feet, and an edge bezel that improves the appearance of the screen, whilst keeping the board neatly tucked away behind it. It's even got a slot in the top for the Raspberry Pi camera!

Please note: Raspberry Pi Touchscreen and Raspberry Pi are not included

Features

  • Durable and hard-wearing ABS Plastic
  • Cut-outs for all connections (USB/HDMI/Composite/Power etc.)
  • Micro SD card hidden for security
  • Fully enclosed touchscreen and Pi increases portability
  • Camera board connector slot
  • Wall mount feature
  • Includes 4 x fixing screws to attach the touchscreen
  • Clip-off rear cover for Pi access
R248.90  Inc VAT
WS HDMI 10.1" 1280x800 (IPS) (B) Touch Screen & Case (1B3 10.1 Capacitive(B)touch display stand)

New to ModMyPi, Wareshare's 10.1" 1280x800 IPS Touch Screen & Case! It's easy to set up, features a great resolution, comes complete with a black acrylic stand, and has touch by default!

Recent upgrades:
If you were used to seeing the Self Test at power on, this has now been removed. However if you remove the jumper located on the controller board you can re-enable this feature.

This device uses the Pi's HDMI output for display, and the Pi's USB port for touch control. Assembly of the Waveshare 10.1" screen is easy, just follow our simple guide here. Please Note. This device does require some simple set up. You will need a UK to EU power adapter.

The LCD Screen Features:

  • 10.1inch HDMI LCD (B)
  • 1280x800 Resolution
  • UK 5V 2A Power Supply Included
  • Capacitive touch control
  • Supports Raspberry Pi, Ubuntu, Windows 10 IoT driver free
  • Can also be used as a computer monitor, supports Windows 10/8.1/8/7/XP etc.
  • Supports BB Black, comes with Angstrom image
  • HDMI interface for displaying, USB interface for touch control
  • Input interfaces: HDMI
  • Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.
  • Firmware is upgradable to support more new features (continually updated)

The Case Features:

  • Material : High quality black and clear Acrylic
  • Comes with bottom holder, 45° tilt angle
  • Features mounting holes for Raspberry Pi 3B/2B/B+/A+/B, and BB Black


Troubleshooting:


For the Windows OS on PC, the resolution of the LCD is automatically identified. Hence, you do not need to make the relative settings. When working with Raspberry Pi, you should set the resolution of the LCD by yourself, or else the LCD screen will not work.


If the display in not working correctly or not displaying at all, you may need to edit setting in the config file.
    sudo nano /boot/config.txt

And add the following to the end of the file:
    max_usb_current=1
    hdmi_group=2
    hdmi_mode=87
    hdmi_cvt 1280 800 60 6 0 0 0
    hdmi_drive=1

If this does not ressolve the problem then use the following instead:
    max_usb_current=1
    hdmi_group=2
    hdmi_mode=27
    hdmi_drive=1



Downloads

User Manual
Quick Assembly Guide

Wiki


R1,659.90  Inc VAT
MAX7219 Dot Matrix Module 4-in-1 Display (1B3 MAX7219 Dot Matrix Display)
Specifications:

A single module can drive a 8x8 dot matrix common cathode
Working voltage: 5V
Module size: 12.8 x 3.2 x 1.3 cm (L*W*H)
With 64 fixing screw holes, hole diameter: 3mm
Module with input and output interfaces, support for cascading multiple modules

Wiring:

1. The left side of the module is the input port, and the right is the output port.
2. Control of a single module, the input port only need to receive CPU.
3. The more a module cascade and input end of the first module is connected with the CPU and input end of the input end of the output end is connected to the second module, output terminal of the second module connected with the three modules, and so on.
For example: 51 SCM
VCC→5V
GND→GND
DIN→P2.2
CS →P2.1
CLK→P2.0

Package includes:

1 x MAX7219 Dot Matrix Module
1 x 5pin jumper Cable


MAX7219 Dot Matrix Module 4-in-1 Display For Arduino


MAX7219 Dot Matrix Module 4-in-1 Display For Arduino


Documentation:
https://max7219.readthedocs.io/en/0.2.3/

Clock example
Python Library
R119.90  Inc VAT
One digit Red 7 Segment 0.56 Inch 1 Bit Common Anode LED Digital Tube (1B3 7 segment single digit)
Features:

Model: 5611BH  Common Anode 
Size: 0.56 inch
Color: red

Package includes:

1 x Red 7 Segment 0.56 Inch 1 Bit Common Anode LED Digital Tube

Some code examples
https://circuitdigest.com/microcontroller-projects/raspberry-pi-7-segment-display-tutorial
https://raspi.tv/2015/how-to-drive-a-7-segment-display-directly-on-raspberry-pi-in-python
R8.98  Inc VAT
ModMyPi - 7" Touchscreen Case and Stand (AW C5 MMP display stand)

Got one of those shiny new Raspberry Pi 7" Touchscreen Displays, and need some way to mount it?! Well, we're proud to introduce ModMyPi's 7" Touchscreen Case and Stand! Made with our trademark stealth-matte black acrylic, and accented with clear (to leave the good bits visible), the case itself is constructed of 7 layers. The rear is protected with a plate of acrylic, so you can leave it flat, or mount it as you wish! Alternatively, we've included a nifty skeleton stand which the case slots into, and the whole unit comes complete with non-slip rubber feet - it is a touchscreen after all, so you don't want it walking across your desk when everyone's poking it!

The case includes an optional clear front layer, which you can leave on or take off if you like the matte finish. You can also sandwich the artwork of your choice in between the two layers, and really customise your Touchscreen case - There's a guide on how to do it here!

Features

  • Raspberry Pi 7" Touchscreen Case & Stand
  • 7 Piece Case
  • 5 Piece Stand with Rubber Non-Slip Feet (Included)
  • Stand Features 2 x M3 Holes for Extra Secure Mounting (Screws not included)
  • Customisable Front Panel
  • Touchscreen Accessible
  • Raspberry Pi & Breakout Board Covered & Protected
  • Easy Access to all Raspberry Pi Ports
  • Assembly Guide

Specification

  • Case dimensions (LxWxD): 240mm x 140mm x 53mm
  • Stand dimensions (LxWxD): 189mm x 150mm x 50mm

Please Note. Raspberry Pi & Touchscreen are not included.

R272.99  Inc VAT
R301.62
Adafruit PiTFT 2.2" HAT Mini Kit - 320x240 2.2" TFT - No Touch (1B3 Ada no touch 2.2)

This product contains only the display. Raspberry Pi, case and cables are shown for illustration purposes only and not included.


The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top of your Model A+ or B+ and fits into our case quite nicely.

It's designed to plug directly onto the Raspberry Pi 2 or Raspberry Pi 1 Model A+ or B+ . While not specifically designed for Pi Model A or B,you can use it with A/B if you solder in an extra-tall 2x13 header (not included) instead of the included 2x20 header.

This design uses the hardware SPI pins (SCK, MOSI, MISO, CE0, CE1) as well as GPIO #25. All other GPIO are unused and are available on a 25-pin long breakout line. Since we had a tiny bit of space, there's 4 flat tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button.

Comes as a fully assembled display PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. You can also swap the plain female header we have with a 'stacky' type that lets you plug in a hat or GPIO cable on top or a slim ultra-low-profile header.

Technical Details

  • Board Dimensions: 65mm x 57mm x 6mm / 2.6" x 2.2" x 0.2"
  • Screen Dimensions: 55mm x 40mm / 2.2" x 1.6"

Tutorials

To make it super easy for use: Adafruit have created a custom kernel package based of off Notro's awesome framebuffer work, so you can install it over your existing Raspbian (or derivative) images in just a few commands. Their tutorial series shows you how to install the software, play small videos, or display images such as from your PiCam and more!

R402.50  Inc VAT
Unicorn HAT (3B4 Unicorn HAT)

What's going to protect your beloved Raspberry Pi from an onslaught of rainbow-coloured fusion? That's right, it's Unicorn HAT.

Sporting a matrix of 64 (8 x 8) RGB LEDs and powered directly from the Pi, this is the most compact pocket aurora available.

Unicorn HAT provides a wash of controllable colour that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting colour into your surroundings.

The MagPi said that Unicorn HAT was "one of the coolest HATs around"

Features

  • 64 RGB LEDs (WS2812B)
  • LED data driven via DMA over PWM
  • Unicorn HAT pinout
  • Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Comes fully assembled

Software

We've put together a Unicorn HAT Python library to make it a breeze to use, including lots of beautiful examples of what it can do.

Notes

  • Warning: WS2812 LEDs are bright enough to cause eye pain, do not look at them directly when brightly lit. We recommend the use of a diffuser.
  • Photo-sensitivity warning: flashing, strobing, and patterns of lights may cause epileptic seizures. Always take care and immediately stop using if you feel unwell (dizziness, nausea, affected vision, eye twitching, disorientation).
  • Power: Unicorn HAT requires a >2A microUSB power supply for your Pi. We recommend the official Raspberry Pi power supply.
  • Compatibility (audio): as Unicorn HAT uses PWM and GPIO18, it will interfere with analogue audio playback (random colour patterns and flickering). HDMI should work just fine!

Short video on the Unicorn HAT

Tutorials & Projects

R341.97  Inc VAT
WS 264x176 2.7 inch 3 colour E-Ink display HAT for Raspberry Pi (1B4 2.7 3colour E-Ink HAT)

Please Note: Raspberry Pi not included

Overview

This is an E-Ink display HAT for Raspberry Pi, 2.7inch, 264x176 resolution, with embedded controller, communicating via SPI interface, supports red, black, and white three-color display.

Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.

Features

  • No backlight, keeps displaying last content for a long time even when power down
  • Ultra low power consumption, basically power is only required for refreshing
  • Compatible with Raspberry Pi 2B/3B/Zero/Zero W
  • Onboard 4x Keys
  • SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
  • Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Specifications

  • Operating voltage: 3.3V
  • Interface: 3-wire SPI, 4-wire SPI
  • Outline dimension: 85mm × 56mm
  • Display size: 57.288mm × 38.192mm
  • Dot pitch: 0.217 × 0.217
  • Resolution: 264 × 176
  • Display color: red, black, white
  • Grey level: 2
  • Full refresh time: 15s
  • Refresh power: 26.4mW(typ.)
  • Standby power: <0.017mW
  • Viewing angle: >170°

Please note: Raspberry Pi not included

Interface

SYMBOLDESCRIPTION
VCC3.3V
GNDGround
DINSPI MOSI pin
CLKSPI SCK pin
CSSPI chip selection, low active
DCData/Command selection (high for data, low for command)
RSTExternal reset, low active
BUSYBusy status output, low active

Development Resources

Wiki : www.waveshare.com/wiki/2.7inch_e-Paper_HAT_(B)

Package Includes:

  1. 2.7inch e-Paper HAT (B) x 1
  2. RPi screws pack (2pcs) x 2
R296.90  Inc VAT
DC-DC Step Down Power Supply Adjustable Module With LCD Display With Case (C51 step down convert & case)





Specifications:


Converter type: DC-DC
Input voltage: 5~23V (Best voltage 20V)
Output voltage: 0V~16.5V (Continuously adjustable)
Peak current: 3A
Mainboard size: 50mm x 30mm x 12mm(LxWxH)
Display module: STN LCD
LCD size: 37.5mm x 17.0mm(LxW)
LCD accuracy: 1%
Conversion efficiency: 95%
Load regulation S(I): <= 0.8%
Voltage regulation S(U): <= 0.8%

Calibration method:

Under power off situation, Holding left button and power the supply,when the  display begin flashing, release left button, with multimeter measuring the output voltage, by pressing the left and right button ,adjust the multimeter measuring voltage to near 5V, such as 5.00V ,4.98V or 5.02V,at this stage, please ignore the display on this item. After adjustment,please power it off and then power on again, calibration is completed. Errors can be calibrated in 0.04V, if the error is greater, you can try to re-calibrate it again.

Package includes:

1 x DC-DC step-down power suppl module
1 x Transparent shell
R179.90  Inc VAT
PiTFT Mini - 320 x 240 2.8" TFT Capacitive Touchscreen (ada 2.8 touch 26pin)

Raspberry Pi not included

Adafruit's best-selling PiTFT just got a fancy upgrade, now we have a version with a capacitive touchscreen! That's right, instead of a resistive touchscreen, which requires a fingernail or stylus, you can now use a fingerpad. The screen looks much nicer, with a black bezel and glass overlay.

Featuring a 2.8" display with 320x240 16-bit color pixels and a single-touch capacitive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top!

It's designed to fit nicely onto the Pi Model A or B rev 2 but also works perfectly fine with the Model B+ as long as you don't mind the PCB overhangs the USB ports by 5mm, see the photos above. Model B rev 1 have an older layout for the I2C pins and won't be able to use the touch screen

Uses the hardware I2C Pins (SDA & SCL), SPI pins (SCK, MOSI, MISO, CE0) as well as GPIO #25 and #24. All other GPIO are unused and you can still share the I2C pins with sensors, LED drivers, etc. Since we had a tiny bit of space, there's 4 spots for optional slim tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button. See below for the link to get the optional tact switches, they're not included.

The screen is the same size as the resistive type so you can use this with the PiTFT PiBow or any other enclosure you may already have. We also use the same SDL device and signals so PyGame and X11 based programs can be swapped in with no changes in code.

This version comes as a mini-kit, with a 2x13 extra-tall female header (to connect the plate to the Pi) and a 2x13 male header that can be used to connect an IDC cable or cobbler from the side. The photos above also show the optional installed slim tactile buttons. The tactile buttons are not included. Some basic soldering is required to install the headers. You can also pick up an extra-long Pi stacking header if you want to install that instead of the 2x13 female header installed.

Technical Details

  • Display current draw is mostly based on the backlight, with full-on backlight the current draw is ~100mA.
  • Screen Dimensions: 50mm x 69mm x 4mm / 2" x 2.7" x 0.16"
  • PCB Dimensions: 56mm x 85mm x 2mm / 2.2" x 3.4" x 0.08"
  • Weight: 44g

Assembly and Installation

Please visit Adafruit for assembly and installation instructions.

R849.90  Inc VAT
WS .RGB LED HAT for Raspberry Pi, colorful display, 8 × 8 grid (1B3 WS RGB LED HAT)

Overview

This RGB LED HAT (B) can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.

Features

  • Supports any revision of Raspberry Pi (directly-pluggable)
  • Onboard 8 × 8 RGB LED (WS2812B)
  • Control pin is configurable via jumpers (0Ω resistor)
  • Break out control pins, easy for working with other MCUs
  • Comes with development resources and manual (examples in Python and Web control)

Specifications

  • Operating voltage: 5V
  • Brightness: adjustable 256 levels
  • Color depth: 24-bit true color (8-bit for R/G/B respectively, totally 256x256x256=16777216 colors)
  • Data rate: 800Kbps(typ)
  • Dimension: 65mm × 56.2mm
  • Mounting hole size: 3.0mm

How to Use

In the case of working with a MCU:

  • 5V ↔ 5V power
  • GND ↔ GND
  • DIN ↔ Signal input

Development Resources

Wiki : www.waveshare.com/wiki/RGB_LED_HAT_(B)

This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R241.10  Inc VAT
MAX7219 Dot Matrix MCU LED Display Control Module Kit (1B3 MAX7219 soldered matrix display single)

1 single module can drive an 8 * 8 dot matrix common cathode
Module Operating voltage: 5 v
Module dimensions: length 32 mm X 32 mm wide X 13 mm high
4 mounting holes : diameter of 3 mm
Support for cascading multiple modules
Wiring instructions:
VCC: 5 v
GND: GND
DIN: P2.2
CS: P2.1
CLK: P2.0


Package includes:

1 x LED module

R29.90  Inc VAT
Discontinued: 0.96 Inch 128 x 64 OLED Module 4 Pin IC I2C IIC Communication (AW 1B5 OLED 0.96inch I2C display)
Description
Connector : IIC port
Pins Definition : 1.GND 2.VCC(3.3~5V) 3.SCL 4.SDA
 
Package Includes:
1 x OLED
R106.82  Inc VAT
WS 10.1inch Resistive Touch Screen LCD HDMI interface (4A1 10.1" Resistive touch display)

Features

  • 1024×600 high resolution
  • Resistive touch control
  • Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable)
  • Drivers provided (works with your own Raspbian/Ubuntu directly)
  • Also works as a computer monitor, in this case, touch panel is unavailable and HDMI cable is required
  • HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os)
  • Backlight can be turned off to lower power consumption

Interface

PIN NO.SYMBOLDESCRIPTION
1, 173.3VPower positive (3.3V power input)
2, 45VPower positive (5V power input)
3, 5, 7, 8, 10, 11, 12, 13, 15, 16, 18, 24NCNC
6, 9, 14, 20, 25GNDGround
19TP_SISPI data input of Touch Panel
21TP_SOSPI data output of Touch Panel
22TP_IRQTouch Panel interrupt, low level while the Touch Panel detects touching
23TP_SCKSPI clock of Touch Panel
26TP_CSTouch Panel chip selection, low active

External Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/10.1inch_HDMI_LCD

R1,239.90  Inc VAT
WS 13.3inch Capacitive Touch HDMI LCD (H) (with case) 1920x1080 IPS (4B1 13.3 capacitve display)

Features

  • 13.3inch IPS screen,1920x1080 high resolution
  • Toughened glass capacitive touch panel, 6H hardness
  • Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
    • When works with Raspberry Pi, supports Raspbian, Ubuntu, WIN10 IOT, single touch, and driver free
    • When work as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free
  • Multi languages OSD menu, for power management, brightness/contrast adjustment, etc.
  • 3.5mm audio jack, supports HDMI audio output
  • Embedded ferrite Hi-Fi speaker
  • Also supports VGA input (specific cable is required and should be purchased separately)
  • 75x75mm spacing mounting holes (M4 screw hole) for general wall mount
  • Comes with 75° tilt angle stand

External Dimension


Development Resources

Wiki : www.waveshare.com/wiki/13.3inch_HDMI_LCD_(H)_(with_case)



R2,399.90  Inc VAT
Picade DIY kit - 8 inch display (3B1 Picade 8inch)

Picade

The ultimate desktop retro arcade machine! Picade is a Raspberry Pi-powered mini arcade that you build yourself, with authentic arcade controls, a high resolution 4:3 display that's ideal for retro gaming, and a punchy speaker to hear those 8-bit game soundtracks at their best

The all-new Picade has been completely redesigned, from the inside out! There's new artwork, a new display and display driver board, dedicated power button, an all-new Picade X HAT, easier wiring, easier access to the interior of the cabinet, beautiful new packaging, a bunch of extra goodies (stickers and an enamel Picade pin), and a gorgeous Picade poster and assembly instructions.

Picade comes in kit form, and it'll take around two to three hours to build. The cabinet is made from powder-coated MDF, giving it a quality look and feel similar to a full-size arcade. All you'll need to add is a Raspberry Pi, power supply, and micro-SD card.

You can watch a video on  Picade at https://youtu.be/5iUuOH1Ip4A

Cabinet features

  • Black, powder-coated panels
  • Acrylic marquee and console with authentic artwork
  • Push-fit arcade buttons
  • Joystick with black ball top
  • 3" speaker (5W, 4Ω)
  • Easy access with removable back panel
  • Dedicated illuminated power button
  • Grippy rubber feet
  • Dimensions: 350x230x210mm

8-inch display features

  • 1024x768 (4:3 ratio) IPS (wide viewing angle) display
  • Pimoroni-designed and manufactured HDMI display driver board and keypad controls
  • Powered by micro-USB cable (included) from your Pi

10-inch display features

  • 1024x768 (4:3 ratio) IPS (wide viewing angle) display
  • Pimoroni-designed and manufactured HDMI display driver board and keypad controls
  • Powered by micro-USB cable (included) from your Pi

Picade X HAT features

  • Easy DuPont connectors for buttons and joystick
  • Push-fit speaker terminals
  • I2S audio DAC with 3W amplifier (mono)
  • Power management, power switch pins, and power button
  • 4-way joystick inputs
  • 6 player buttons
  • 4 utility buttons
  • Metal standoffs to hold your Picade X HAT securely

Extras

  • Picade enamel pin badge
  • Pimoroni Super Sticker Selection
  • Picade poster / assembly instructions

What's new!?

The cabinet is more compact, so it fits more neatly on your desk, but has a higher resolution 8"  or 10" display (1024x768). The display is driven by a new Pimoroni-designed and manufactured driver board, with keypad controls. It's an IPS panel, so it looks great from any viewing angle!

The all-new Picade X HAT is packed full of useful features. We've moved from more fiddly screw terminals to simple DuPont connectors that just push in, and the speaker terminals are the same easy push-fit connectors that we use on pHAT BEAT.

There's dedicated power management on-board Picade X HAT; just plug your micro-USB power supply into the HAT and it'll power your Pi through its pins. The power button connected to the HAT means that once your Pi is safely shutdown, the power will be cut completely to the Pi. A simple press of the power button will boot your Picade up again.

The new buttons in Picade are lower profile, and the new joystick has a single connector rather than the eight spade connectors on our previous Picade joystick.

A gorgeous new neon-look Picade logo on the marquee, and rainbow stripes on the console and screen-surround, evoke classic consoles, as do the assembly instructions and poster.

Building your Picade

We hope the included assembly instructions have everything you need to build your Picade, but we've also filmed a complete build video of Picade that you can watch as you build and learn some handy tips and tricks. Find it at https://youtu.be/gTgu1fUVsmw

The sections are also available separately in a playlist here.

We've also put together an online tutorial that incorporates the assembly instructions, important tips and amendments, and the videos for each section, so do check that out!

Software setup

We recommend the RetroPie operating system for your Picade. You can download it from the RetroPie website and then burn it to a micro-SD card with Etcher.

Connect a USB keyboard to your Pi, and connect to Wi-Fi in the RetroPie menu. Press F4 to exit to the terminal and then type curl https://get.pimoroni.com/picadehat | bash to run the Picade HAT installer.

Reboot your Pi, if it doesn't prompt you to. Press the "Alt" key on your keyboard and then select "Configure input" to configure your Picade's controls. You'll find that the sound and power button should both be working now too!

Notes

If your Picade display doesn't show anything when you first power it up, then it could be because the HDMI display is not being detected by the Raspberry Pi. This can happen because power isn't supplied to the USB ports on the Raspberry Pi for the first few seconds of booting. The solution is to edit the /boot/config.txt file on your RetroPie SD card, and add hdmi_force_hotplug=1 on a new line at the bottom of the file.

If you'd like to design your own artwork for your Picade, then we've made a handy PDF that has the outlines and dimensions of the marquee, screen shim, and console. You can download it from the Picade HAT GitHub repo here.

Where to find ROMs for RetroPie (free and legally) https://howchoo.com/g/otiwyjhlnzb/where-to-find-roms-for-retropie

and here http://cvaddict.com/article.php?articleid=15

R2,499.90  Inc VAT
Per Page      1 - 20 of 52