Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
This module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor
R29.90  Inc VAT
The L293D Dual H-Bridge IC is able to run four solenoids, two DC motors or one bi-polar or uni-polar stepper motor, with up to 600mA per channel!
R14.90  Inc VAT
This pulley is for 2mm pitch 6mm width GT2 timing belt.
R129.90  Inc VAT
This motor driver board for the micro:bit allows two motors to be driven with forward, reverse, and stop control, and allows access to the other pins.
R279.90  Inc VAT
R199.90  Inc VAT
R209.90
CJMCU 24 Bit WS2812 5050 RGB LED Driver Development Board (RGB ring 24)
Description:
 
Voltage: DC 5V 
Colour: RGB 
Outer diameter 85mm, 70mm inner diameter 

Soldering will be required to connect your wires

 
What's in the box?
 
1 x 24 Bit RGB LED Driver Development Board
R89.90  Inc VAT
Stepper Motor with ULN2003 Driver (DC 5V) (Stepper and pcb driver)
Description:

The maximum speed for a 28byj-48 stepper motor is roughly 10-15 rpm at 5 V.

The 28BYJ-48 motor runs in full step mode, each step corresponds to a rotation of 11.25°. That means there are 32 steps per revolution (360°/11.25° = 32). In addition, the motor has a 1/64 reduction gear set.

The power consumption of the motor is around 240mA.


The ULN2003 is one of the most common motor driver ICs, consisting of an array of 7 Darlington transistor pairs, each pair is capable of driving loads of up to 500mA and 50V. Four out of seven pairs are used on this board.


The board has four LEDs that show activity on the four control input lines (to indicate stepping state). They provide a nice visual when stepping.

The board also comes with an ON/OFF jumper to isolate power to the stepper Motor.

Specifications:

- High quality stepper motor with ULN2003 driver
- Suitable for microcontroller development
- Voltage: DC 5V
- Diameter: 28mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
Dimensions: 1.38 in x 1.18 in x 0.39 in (3.5 cm x 3.0 cm x 1.0 cm)
Weight: 1.45 oz (41 g)

What's in the box?:

1 x stepper motor
1 x ULN2003 driver

Resources:

How to control a ULN2003 stepper motor with Raspberry Pi

R58.90  Inc VAT
L9110S H Bridge Stepper Motor Dual DC Driver Controller Module (L9110S small H Bridge)

Description:

There are two L9110S motor controller chips onboard
This module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor

Feature:

Work under low static current
Power supply voltage: DC 2.5V - 12V
Each channel has 800mA continuous current output
Low saturation pressure drop
TTL / CMOS output level compatible, can be connected directly to the CPU
Output built-in clamping diode, apply to the perceptual load
Control and drive integrate in IC
Pin high pressure protection function
Working temperature: 0°C - 80°C
Size: 29 x 21mm(L x W)

Circuit diagram:

 


Package includes:

  1x L9110S stepper motor driver

Robot control with Python

This module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor
R29.90  Inc VAT
L298N Dual H-Bridge Stepper Motor Driver Board (H Bridge big red dual stepper)
Description:

The L298N is a dual H-Bridge motor driver which allows speed and direction control of two DC motors at the same time. The module can drive DC motors that have voltages between 5 and 35V, with a peak current up to 2A.

Specifications:

Double H bridge drive
Chip: L298N (ST NEW)
Logical voltage: 5V
Drive voltage: 5V-12V
Logical current: 0mA-36mA
Drive current: 2A (MAX single bridge)
Storage temperature: -20 to 135
Max power: 25W
Weight: 30g
Size: 43 x 43 x 27mm

Note:

This module has a built-in 5v power supply, when the driving voltage is 7v-12v, this supply is suitable as a power supply.
DO NOT connect input voltage to 5v on controller interface.
When ENA is enabled IN1 IN2 control OUT1 OUT2
When ENB is enabled IN3 IN4 control OUT3 OUT4

Note:  Package does not include the board mounting screws.

Package includes:

1 x  L298N Module

Resources:

Robotic control with python



R44.90  Inc VAT
Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board (Adaf TB6612 stepper driver)
Description:

Fire four solenoids, spin two DC motors or step one bi-polar or uni-polar stepper with 1.2A per channel (3A peak) using the TB6612.

 We really like these dual H-bridges, so if you want to control motors without a shield or HAT these are easy to include on any solderless breadboard or perma-proto.

We solder on TB6612 onto a breakout board for you here, with a polarity protection FET on the motor voltage input and a pullup on the "standby" enable pin. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive four solenoids, two DC motors bi-directionally, or one stepper motor. Just make sure they're good for 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 3A but that's just for a short amount of time. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver!

There's two digital inputs per H-bridge (one for each half of the bridge) as well as a PWM input per driver so you can control motor speed. Runs at 2.7V-5V logic. The motor voltage is separate from the logic voltage. Good for motor voltages from 4.5V up to 13.5V! This wont work well for 3V motors.

Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included. Check out the handy tutorial on assembly and wiring!

Specifications:

  • Current Limit: 1.2A
  • Size: 27mm x 19mm x 3mm / 1.1" x 0.7" x 0.1"
  • Weight: 1.8g



What's in the box?:

1 x TB6612 driver
1 x header strip

R126.90  Inc VAT
ULN2803A: 8 Channel Darlington IC - Solenoid, DC & Stepper Motor Driver (Darlington stepper driver IC)
Description:

Bring in some muscle to your output pins with 8 mighty Darlingtons! This DIP chip contains 8 drivers that can sink 500mA from a 50V supply and has kickback diodes included inside for driving coils. This will let your little microcontroller or microcomputer power solenoids, DC motors (in one direction) and unipolar stepper motors. The inputs can be driven by 3.3V or 5V logic and the IC fits nicely in any breadboard or perfboard.
 
Please note, this is an 'open collector' driver - it can only be used to connect the load to ground and there will be a 1 Volt (or more) 'drop' across the internal transistors.
 
This is a genuine Toshiba part, not a cheap replica! 
 
The ULN2803: 8 Channel Darlington IC (Solenoid/Unipolar Stepper Driver) Features:
  • The ULN2803APG / AFWG Series are high−voltage,high−current darlington drivers comprised of eight NPN darlington pairs.
  • All units feature integral clamp diodes for switching inductive loads.
  • Applications include relays, hammer, solenoid, unipolar steppers, lamp and display (LED) drivers etc.
  • Output current (single output): 500 mA (max)
  • High sustaining voltage output: 50 V (min)
  • Output clamp diodes
  • Inputs compatible with various types of logic.
  • Package Type−APG : DIP−18pin

What's in the box?:

1 x 8 Channel Darlington IC

Downloads

ULN2803 Data Sheet

Tutorials

How to Control a Stepper Motor using your Raspberry Pi & the ULN2803 Driver Chip

R28.90  Inc VAT
L293D Dual H-Bridge IC - Solenoid, DC & Stepper Motor Driver (L293D IC H-bridge)
Description:

The L293DNE Dual H-Bridge IC is able to run four solenoids, two DC motors or one bi-polar or uni-polar stepper motor, with up to 600mA per channel!
 
Each chip contains two full H-bridges (four half H-bridges) which means you can drive four solenoids, two DC motors bi-directionally, or one stepper motor. Just make sure they're good for under 600 mA since that's the limit of this chip. They do handle a peak of 1.2A but that's just for a short amount of time. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver
 
 
The L293D Dual H-Bridge IC - Stepper & DC Motor Driver Features:
  • Dual H-Bridges - run four solenoids, two DC motors, or one uni-polar or bi-polar stepper motor
  • Output Current: 600mA per channel (1.2A Max)
  • No of Channels: 4
  • Input: 5V Logic
  • Supply Voltage Range: 4.5V to 36V
  • No. of Pins: 16
  • Operating Temperature Range: 0°C to 70°C


What's in the box?:

1 x L293D Dual H-Bridge IC

Downloads

L293DNE Data Sheet

Tutorials

Controlling a Stepper Motor with the L293D

Raspberry Pi: Controlling a DC Motor

Arduino: Stepper Motors

Arduino: DC Motor Reversing

The L293D Dual H-Bridge IC is able to run four solenoids, two DC motors or one bi-polar or uni-polar stepper motor, with up to 600mA per channel!
R14.90  Inc VAT
GT2 Aluminum Timing Drive Pulley 36 Teeth (GT2 pulley 36T)
This pulley is for 2mm pitch 6mm width GT2 timing belt.

Description:

The timing belt originally comes from the automotive sector. Later developments of belt shapes resulted from the use of timing belts in scanners. Today, the 3D printer sector is able to benefit particularly from these developments. Toothed belt drives are a very common drive element for positioning in the 3D printer industry due to their high positioning accuracy and the small installation space required. Additional advantages include their low maintenance requirements and long service life.

Specifications:

Teeth: 36 (T)
Pitch: 2 (mm)
Bore: Dia.5 (mm)
Material: Aluminum Alloy
Belt Width: 6 (mm)

Package includes:

1 x GT2 Aluminum timing belt pulley
This pulley is for 2mm pitch 6mm width GT2 timing belt.
R129.90  Inc VAT
Kitronik Motor Driver Board v2 for the micro:bit (micro:bit motor driver)

Description:

This motor driver board for the micro:bit allows two motors to be driven with forward, reverse, and stop control, and allows access to the other pins.

This board provides a simple way to add motor driving capability to a micro:bit. It allows two motors to be driven with full forward, reverse & stop control. It has terminal blocks to connect four input devices and a regulated 3V supply is fed in to the 80 way connector to power the inserted micro:bit.

In this new version, the pins from the micro:bit are now broken out to pads on the end of the motor driver board. These pads can either be soldered onto directly, or they are the correct spacing for our PCB pin headers (see image below for a close up of the new pads).

It is ideal for designs such as buggies (see below).

It includes an integrated edge connector slot for your micro:bit to easily slot into. It also features external connections to the buttons A and B inputs. This allows additional switches to be connected to the motor driver board and the state of these can then be read by the micro:bit.

Get up to speed quickly. Example Microsoft TouchDevelop code and example connections in the datasheet (below).

Features:

  • Drive 2 motors with full forward, reverse, and stop control
  • Terminal blocks for easy connection of motors and inputs
  • 4 inputs (2 analogue inputs and 2 provide external connections to buttons A and B as inputs)
  • Includes edge connector for the micro:bit to slot into
  • Provide regulated power to the micro:bit
  • Access the other micro:bit pins easily and conveniently

Contents:

  • 1 x edge connector motor driver board for the micro:bit

Dimensions:

  • Length: 67mm
  • Width: 61mm
  • Height: 18mm
Watch the video: https://youtu.be/muC6vrhNM-s

Resources:



This motor driver board for the micro:bit allows two motors to be driven with forward, reverse, and stop control, and allows access to the other pins.
R279.90  Inc VAT
Sandisk industrial micro SD 16GB C10 (Industrial uSD 16GB Sandisk)

Description:

The SanDisk Industrial SD™ and microSD™ cards deliver superior endurance and reliability for demanding industrial applications across a wide range of operational requirements. Typical applications include commercial surveillance cameras, drones, Industrial IoT gateways, factory automation, and network equipment. These hard-working, connected devices can now take advantage of a powerful suite of features available in our industrial-grade flash storage solutions

Specifications:

  • Fast Read/Write performance enables high bit-rate video streams for commercial imaging applications such as surveillance and Industrial IoT
  • “Smart” features including Health Status Monitor for proactive device status monitoring, and Automatic Read Refresh to prevent flash storage from being corrupt
  • Class 10
  • 16GB
  • SDA 3.0 High Speed
  • -25°C to 85°C
What's in the box:

1 x Industrial micro SD 16GB C10

Resources:

Raspberry Pi Operating System Downloads: https://www.raspberrypi.org/downloads/
R199.90  Inc VAT
R209.90
1.75mm Brass Feed Extruder Wheel Drive Gear For Reprap 3D Printer (1.75mm feed wheel)
Description:

These drive 40 teeth gears are made of quality brass, rustproof and no corrosion, durable and stable to use, with good bearing capacity. Fits a large range of 3D printers

Specifications:

- Material: brass
- Color: golden
- Model: reprap
- Operation temperature: 250°
- Style: 1.75mm
- Installation: female connection
- Used for 1.75mm filament


Package includes:

1x Feed Wheel
R39.90  Inc VAT
TB6600 32 Segments 4A 40V 57/86 Stepper Motor Driver (TB6600 stepper driver)
Description:

TB6600 is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers that can output a 5V digital pulse signal. TB6600 arduino stepper motor driver has a wide range power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for the most of stepper motors.

The stepper driver supports speed and direction control. You can set its micro step and output current with 6 DIP switch. There are 7 kinds of micro steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing its anti-high-frequency interference ability.

As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.

Features:

1. 9V-40V DC power supply
2. H-bridge bipolar constant phase flow driver
3. The maximum output current is 4.0A (eight optional)
4. Up to 32 segments of six kinds of sub-modes available
5. Input signal high-speed photoelectric isolation
6. Standard common anode single pulse interface
7. Offline keep function
8. Semi-enclosed chassis can adapt to a more demanding environment
9. Provide energy saving semi-automatic current lock function
10. Built-in thermal protection and over-current protection


Specifications:

Voltage: up to 50V
ON resistance (upper lower) = 0.4 Ω
Forward and reverse rotation control
5 kinds of sub-modes selectable (1/1, 1/2, 1/4, 1/8, 1/16 step)
Output current: IOUT = 5.0A (peak within 100ms)
Rated output: IOUT = 4.5 A
Input pull-down resistor: 100 KΩ
Current output alarm pin: Ialert = 1mA
Monitor output pin (MO): Imo = 1mA
With reset and enable pins
With a standby function.
Breaking the traditional single-supply
Built-in thermal protection (TSD) circuit
Built-in voltage protection (UVLO) circuit
Built-in over current detection (ISD), the circuit


Note:

This driver is the upgraded version TB6600, heightening segment to 32 subdivision, suitable for high segmentation applications.
For step motor: 42, 57, 86 type 2 phase 4 phase (4 / 6 / 8 line)


What's in the box?

1 x TB6600 Stepper Motor Driver Controller

Resources:

https://danielwilczak101.medium.com/control-a-stepper-motor-using-python-and-a-raspberry-pi-11f67d5a8d6d

https://www.instructables.com/Raspberry-Pi-Python-and-a-TB6600-Stepper-Motor-Dri/





R299.90  Inc VAT
TB6560 3A CNC Router 1 Axis Driver Board Stepper Motor Drivers (TB6560 driver board)
Description:

The TB6560 stepper motor control circuit is the most commonly used current circuit, which can control a 2 phase motor (10 – 35VDC) with a maximum output of 3A.

Specifications:

Size: 75mm x 50mm x 35mm  (L x W x H)
Rated maximum output: ± 3A, peak 3.5A
Working voltage: DC 10V-35V
Recommended to use a switching power supply: DC24V power supply
Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 Subdivisions.

Feature:

Using the Toshiba TB6560AHQ new original chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance.
For two-phase within 42, 57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor.
Automatic half current function.
6N137 high-speed optical coupling, guarantee high speed without losing step.

Features similar products:

1. Current grade-by-adjustable to meet your demand for a variety of applications.
2. Semi-automatic flow adjustable.
3. 6N137 high-speed optical coupling, guarantee high speed without losing a step.
4. Thick teeth heat sink for good heat dissipation.

Package includes:

1 x TB6560 1 axis driver board
R169.90  Inc VAT
DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Board (A3967 easy stepper driver)
Description:
 
1. The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0V to 5V pulse. (or 0V to 3.3V pulse if you solder SJ2 closed on the EasyDriver)
2. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor.
3. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4, 6, or 8 wire stepper motors.
4. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the micro stepping resolution. The sleep and enable pins are also broken out for further control.

 
Features:
 
1. MS1 and MS2 pins broken out to change micro stepping resolution to full, half, quarter and eighth steps (defaults to eighth)
2. Compatible with 4, 6, and 8 wire stepper motors of any voltage
3. Adjustable current control from 150mA / phase to 750mA / phase
4. Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds
5. Distribution pin, not welded, this module is open source
 
Note:
 
Do not connect or disconnect a motor while the driver is energized.This will cause permanent damage to the A3967 IC.
Chip data: http://www.alldatasheetcn.com/datasheet-pdf/pdf/83571/ALLEGRO/A3967.html
 
We found 2 great tutotials at the below links:

Package includes:


 
1 X A3967 easy driver stepper motor driver board
R51.12  Inc VAT
R69.90
HT16K33 LED Dot Matrix Drive Control Module Digital Tube Driver Development Board (HT16K33 LED Dot Matrix Driver)
Description:

The HT16K33 is a memory mapping and multi-function LED controller driver. The max. Display segment numbers in the device is 128 patterns (16 segments and 8 commons) with a 13*3 (MAX.) matrix key scan circuit. The software configuration features of the HT16K33 makes it suitable for multiple LED applications including LED modules and display subsystems. The HT16K33 is compatible with most microcontrollers and communicates via a two-line bidirectional I2C-bus.

Features:

Operating voltage: 4.5V~5.5V.
Integrated RC oscillator.
I2C-bus interface.
16*8 bits RAM for display data storage.
Max. 16 x 8 patterns, 16 segments and 8 commons.
R/W address auto increment.
Max. 13 x 3 matrix key scanning.
16-step dimming circuit.
Selection of 20/24/28-pin SOP package types.


Applications:

Industrial control indicators.
Digital clocks, thermometers, counters, multi meters.
Combo sets.
VCR sets.
Instrumentation readouts.
Other consumer applications.
LED Displays.


Package included:

1 x Module

Getting Started

R57.40  Inc VAT
R79.90
Blue TMC2100 LV8729 Stepper Motor Driver Cooling Heatsink With Back Glue For 3D Printer (blue driver heatsink)
Description:

New design heatsink, greater contact area, improved cooling effect.


Specifications:

Color: Blue
Material: Aluminum
Function: Heat dissipation
Suitable for TMC2100/LV8729 stepper motor driver
Dimensions: 16.5*16.5*14.5mm (L * W * H)

Package Includes:

1 x Heatsink


R14.90  Inc VAT
3D Printer Stepstick Drv8825 Stepper Motor Driver replace A4988 (purple print driver)
Product Features

1 simple steps and direction control interface
2 six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step
3.CAN interface directly with 3.3 V and 5 V systems
4 Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout
5 short to ground short circuit load protection
6.4 Layer 2 oz copper PCB, in order to improve heat dissipation
7 exposed solder ground below the bottom of the driver IC on the printed circuit board pad
8 module size, pin and interface matching A4988 stepper motor driver operators in many ways
9 adjustable current control lets you set a potentiometer, which lets you use the stepper motor's rated voltage or more, in order to achieve a higher rate of maximum output current step
10 Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)
11 Maximum 45 V supply voltage
12 built-in voltage regulator (the need for any external logic supply voltage)


How to control a stepper motor with Arduino
R95.90  Inc VAT
125KHz Black USB Proximity Sensor Smart rfid Card Reader EM4100,EM4200,EM4305,T5577,or compatible cards/tags no driver needed (125KHz usb reader)

Product Description

1, Support EM4001, EM4100, EM4200, TK4100 and its compatible RFID ID card

2, Frequency: 125KHz

3, First 10 digits of the RFID proximity card read.

4, Windows95/98/2000/XP/7/8/10/android

5, Communication speed: 106Kbit/s

6, Power: DC 5V

7, Reading distance: 5-8cm

8, Interface: USB

9, Operation temperature: -10~70 celsius degree

10, Storage temperature: -20~80 celsius degree

11, Size(L*W*H): 108mm x 78mm x 28mm

12, Total Weight: 100g

13, Color: Black

 

Installation Instructions

1: Connect the usb cable with the card reader to the computer USB port.

2: The reader will 'drip' sound and flash about that power successfully,

and then half a second after the 'drip' sound and flash about that device self-test successfully, without Installing any drivers, windows will automatically recognize it.

3: Open notepad and scan a card to test.

 

Application:


Widely used in entrance guard, consumption, hotel lock, water meter, electricity meter and gas meter and a series of IC card management application systems.

Product function:


1.Fast in reading the RFID Tags
2.Connects to PC to read the RFID tags and update to the application

Package includes:
  • RFID ID Card Reader x 1
  • USB cable x 1
R159.90  Inc VAT
WAVGAT cnc shield v3 engraving machine / 3D Printer / A4988 driver expansion board for Arduino (cnc shield only)
Description:

The CNC Shield V3.0 allows you to build a engraving machine, 3D printer, mini CNC and other similar devices using your Arduino. It is designed as a shield and can plug on top of an Arduino requiring no external connections and wiring. There are 4 slots on the board for plugging in stepper motor drive module which can drive 1 stepper motor each. Controlling each step stepper motor requires only two IO pins on the Arduino. Just insert this Arduino CNC Shield V3.0 onto an Arduino UNO, and install the GRBL firmware, you can then quickly build a DIY CNC engraving machine. 



Features:

  • The extension board can be used for Small CNC routers, Carving Machine, 3D Printers, DIY Laser Cutters, and almost any project where you need to control a stepper motors with high precision
  • This shield allows you to control upto 4 stepper motors
  • Controller each stepper motor requires 2 IO Pins only, which saves a lot of IO Pins for other purposes
  • Arduino compatible
  • Latest Arduino CNC Shield Version 3.10
  • GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
  • Supports PWM Spindle and direction pins
  • 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
  • Supports Coolant enable
  • Supports removable A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
  • Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
  • Compact design.
  • Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
  • Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
  • Uses removable A4988 or DRV8825 compatible stepping driver.


What's in the box?

1 x CNC shield

Resources:

After installing the official IDE software please copy the 3 folders in the update folder to the following path:

C:\Users\Administrator\Documents\Arduino

Restart the software
Select the development board model
[Tools] -> [Board] -> WAVGAT UNO R3

Select COM port
[Tools] -> [Serial Port] -> Select the corresponding COM port

You can now use the development board

Download information:  https://drive.google.com/open?id=10gwrG9uTDwaEO-7EudsmBkfgdcyrcABI
R68.90  Inc VAT
EleksMaker Mana 3 Axis Stepper Motor Driver Board Controller For DIY Laser Engraver (Laser 3 axis driver board)
EleksMaker® Mana 3 Axis Control Board is not only for EleksMaker EleksMill Machine, but also suitable for most mini 3 axis cnc engraving machines of the market (such as 3018 / 2417 CNC Router).

Specifications:
General Specification
 Brand EleksMaker®
 Model Mana
 Product Name 3 Axis Control Board
 Product Size 90mm x 50mm x 20mm
 Board Dimension (L*W) 80mm x 77mm
 Technical Parameters
 Interface Port Micro USB
 Supply Voltage  DC12V-5A
 Operating System  Windows 7/8/10
 Software Support  EleksCAM (Recommended) / Candle / T2-Laser...
 Support Axis  3 Axis
 Support Stepper Motor  Motor within 2A  2-phase 4-wire
 Power Interface  DC5.5 - 2.1  (Inside is positive  electrodes and outside is negative electrodes)

Features:
1. Expansion of functions: stop, pause, resume, fans, low light, external relay.
2. Fit for DIY desktop laser engraver,dispensing machines printer,plotter,tool CNC.
3. Three axis linkage, Y-axis dual interface, can drive a stepper motor within 2A 2-phase 4-wire.
4. Micro USB interfaces, 12V power supply, delivery lines! Send software! Technical support!
5. Large MOS tube, onboard DC buck module, wire jump ADJ can adjust manually the laser voltage to control the laser power.
 
Tips:
- Official EleksCAM Software Download Link: http://wiki.eleksmaker.com/doku.php?id=elekscam;
- Interface Description: http://wiki.eleksmaker.com/doku.php?id=eleksmanav5.1
 
Note:
1. There isn't a  Voltage Regulator Module in this Laser board.
2. Please use EleksCAM software if you want to use this control board on 3018 router or other 3 axis cnc engraving machine.
3. The motor can not work higher than 2A, when the motor work for a long time in 1A to 2A , please pay attention to heat.
 
Package Includes:
1 x 3 Axis Driver Board
1 x USB Cable
5 x Connector Wires
R679.90  Inc VAT
Per Page      1 - 20 of 38