Robotics

Robotics
Sort By:  
SC15 17kg Large Torque Programmable Serial Bus Servo (programmable serial servo)
Description:

SC15 Programmable Serial Bus Servo

Specifications

PRODUCT TYPESC15 serial bus servo
TORQUE[email protected]; [email protected]; [email protected]
ROTATION ANGLE180° (servo mode angle control) / 360° (motor mode continuous rotation)
POS SENSOR RESOLUTION180° / 1024
MECHANICAL LIMITED ANGLENo Limit
OPERATING VOLTAGE4.8-8.4V
GEARhigh precision metal gear
IDLING SPEED0.18sec / 60°@4.8V 0.16sec / 60°@6V
ID RANGE0-253
BAUDRATE38400bps ~ 1Mbps
FEEDBACKPosition, Load, Speed, Input Voltage
IDLING CURRENT200 mA
STALLING CURRENT1700 mA

Application Examples
  • Servos will provide various feedback like position, speed, torque lock, operating mode (servo mode, servo motor mode, etc.) for advanced projects requiring closed-loop automatic control
  • Ideal choice for building quadruped robots, hexapod walkers, robotic arms and other robotic projects requiring multiple servos

* images here are for reference ONLY

UART Serial Bus Control

Up To 253 Servos Can Be Connected In Series At The Same Time



Note: though one channel UART is able to control up to 253 bus servos, due to the high power of the servos, it is necessary to consider whether the power supply solution is enough when using too many servos. The servo driver board is NOT included, please purchase separately if needed.
Large Torque

Up To 17kg.Cm Torque On 8.4V Voltage, Suitable For Building Quadruped Robots, Hexapod Walkers, Robotic Arms And Other Robotic Projects Requiring Multiple Servos


for reference only, the JETANK robot is NOT included.

Two-Way Feedback




The Servos Will Provide Various Feedback Like Position, Load, Speed, And Input Voltage,

In Real Time

Dual Modes: Servo Or Motor

precise rotation angle control, on servo mode

 

continuous rotation, on motor mode

 

Details Introduction

Nylon and fiberglass case
Improved heat-resistance, size stability, rigidity, and mechanical performance

 

High strength aluminum servo wheels
Using T6061 aluminum alloy, good corrosion-resistance

 

High precision copper and steel gears
Ingenious combination of the two, lower operating noise, better stability and mechanical performance

Outline Dimensions


PACKAGE CONTENT

Weight: 0.07 kg

  1. SC15 Servo x1



R359.90  Inc VAT
Tracking Robot Car Electronic DIY Kit With Reduction Motor (DIY track robot kit)
Description:

This kit introduces quite a few electronic principles, its fun and not difficult to build. This is a self-build DIY smart tracking robot car kit. It is an introductory electronic kit designed to help kids, electronic enthusiasts, and novices learn about basic electronic knowledge like soldering and simple circuits(photoelectric sensor circuit, voltage comparator, motor driving,ir sensors etc.) The smart kit is designed based on the principle of infrared sensor and light reflectivity difference when the light emitting on the white and black items




The assembly steps:


Step 1: Welding circuit

Soldering part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted

Step 2: Mechanical assembly

The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire an be used for motor wire.

Step 3: The installation of a photoelectric circuit

Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test.

Step 4: Vehicle debugging

The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side.

Note: We don't supply any manuals please note this before you buy it.

Package includes:

1 x Electronic DIY Kit (batteries are not included)



R199.90  Inc VAT
DC 3V Mini Motor 130 (3V dc motor mini)
Description:

This high-power, 130-size brushed DC motor can be used as a direct replacement for lower-power 130-size motors to get more torque and speed out of your gearmotor, but it will also draw more current and typically wear out faster.

It has a recommended operating voltage of 1.5 V to 3 V, but it can operate at higher voltages to provide more power in exchange for longevity of the motor.

Approximate specifications at 3 V: free-run speed of 20,000 RPM, free-run current of 350 mA, stall current of 4 A, stall torque of 55 gf-cm (0.75 oz-in).

Specifications:
 
Motor size: 38x20x15mm
Shaft diameter: 2mm 
Axial length: 9mm 
Voltage: 3-6V
 
Package Includes:
 
1 x DC 3V Mini Motor

Resources:

Getting started with Raspberry Pi gpiozeroMotors
Controlling DC Motors Using Python With a Raspberry Pi
R11.90  Inc VAT
MG996R Servo Metal Gear High Torque (MG996R Servo)
Description:

The MG996R is a metal gear servo motor with a maximum stall torque of 11 kg/cm. Like other RC servos the motor rotates from 0 to 180 degree based on the duty cycle of the PWM wave supplied to its signal pin.



Specifications:
  • Product: MG996R Servo
  • Torque: 9kg/cm(4.8V), 11kg/cm(6V)
  • Speed: 0.19s/60°(4.8V), 0.18s/60°(6V)
  • Rotate angle: 180°
  • Operating voltage: 4.8 ~ 6V
  • Gear: metal
  • Dead band: 5us
  • Weight: 55g
  • Dimension: 40.7mm × 19.7mm × 42.9mm


What's in the box ?

1 x MG996R Servo with Arm kit




R84.90  Inc VAT
Animatronic Head Kit for micro:bit (Animatronic Head micro:bit )
Description:

This kit contains everything you need (except a micro:bit and batteries) to make an animatronic head with two moving eyeballs and sound from a loudspeaker.

The kit includes software for three simple projects, but we also hope that you will use this kit to write you own programs and you can also add to the basic head mechanism and build it into something even more fun.

Specifications:




What's in the box ?

1 x Servo for micro:bit
1 x speaker for micro:bit
2 x 9g micro servomotors
1 x 3 AA battery box 
1 x Alligator clip leads (10 Leads)
2 x Ping-pong balls with servo connector
1 x Laser-cut acrylic piece marked A (front)
1 x Laser-cut acrylic piece marked B (back)
1 x Laser-cut acrylic piece marked C (top)
1 x Laser-cut acrylic piece marked F (base)
2 x laser-cut acrylic piece marked D (spacers)
1 x Laser-cut acrylic piece marked E (pegs)
1 x M3 steel nut and bolt pairs
1 x M2 plastic nut and bolt pairs
1 x Small screw-driver
1 x Spanner

(* micro:bit & Batteries NOT INCLUDED)


Resources :

- Instructions (PDF)
- Data Sheet (PDF)
- High Res images (Google Drive)





















R759.90  Inc VAT
Per Page      41 - 45 of 45