All Products

Our 2 x D type battery holder is perfect for hobbyists looking for a reliable power source for their DIY electronics projects.

Argon ONE V3 Case is made compatible for Raspberry Pi 5 with upgraded features and all new black finish.

The ESP32-C5-WIFI6-KIT is a development board designed by Waveshare based on the ESP32-C5-WROOM-1 module for dual-band Wi-Fi and multi-protocol IoT gateway applications.

Creality Hi Ceramic Heating Block, High Thermal Conductivity, Quick-swap Nozzle, 300℃ High Temperature Resistance

The BME680 is a "4-in-1" sensor that measures temperature, humidity, barometric pressure, and volatile organic compounds (VOC) gas. It is a favorite for weather stations and air quality monitors

A year ago we designed a high-current-output Infrared Transmitter STEMMA which makes it easy to create high-powered IR LED blasters. Now we've sat down to design the other side, the super sensitive wide-range Adafruit Infrared IR Remote Receiver with two selectable IR receiver chips.

This 5-Port Passive Hub board has 5 vertical JST SH 1mm connectors in a row, all with the power, ground and SDA/SCL pins connected. There are also breadboard breakout pins if you need them. Use this hub to add as many I2C devices to the bus as you need.

This 4-wire cable is a little over 150mm long and fitted with JST-SH (Qwiic/STEMMA QT) female 4-pin connector on one end, and male jumper wires on the other.

This 4-wire cable is a little over 150mm long and fitted with JST-SH (Qwiic/STEMMA QT) female 4-pin connector on one end, and female jumper wires on the other.

This 4-wire cable is a little over 300mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

These are handy for extending a Stemma QT or Qwiic cable if you don't have one long enough for your project, or to protect a port if you're regularly swapping out sensors/dev boards. The pin connections are 1-1, matching both sides.

This 4-wire cable is a little over 200mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

The Adafruit VL53L4CX Time of Flight Sensor is another great Time of Flight distance sensor from ST in the VL5 series of chips, this one is great for long distances - it goes up to 6 meters compared with 4 meter max of the VL53L1X.

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around and often have little detents for tactile feedback.

This OLED goes out to all the fans who want more pixels in a smaller size! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one is a whopping 128x128 pixels in crisp monochrome.

Vishay has a lot of light sensors out there, and this is a nice simple lux sensor that's easy to add to any microcontroller. Most light sensors just give you a number for brighter/darker ambient lighting.

The Adafruit LIS3DH Accelerometer Breakout packs low-power consumption, flexible I2C/SPI connectivity, and advanced motion detection into a compact, STEMMA QT-ready board—perfect for wearables, motion sensing, and battery-powered projects.

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. The SHT41 sensor is the fourth generation of I2C temperature and humidity sensor from Sensirion.

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed.