Switches/buttons
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- Green Colour
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Gold Plated Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
What's in the box?
1 x arcade button
Specifications
- Size: (Approx.)12x12x7.3mm
- Life: 100000 times
- Quantity: 10pcs
- Current: 50mA
- Voltage: 12V
What's in the box?
10 x Push Button Switch
Resources
This flexible 4x4 matrix keypad is connected to an 8 pin DuPont Female connector. It can be attached to a surface via the adhesive back by removing the white protective paper backing.
- Contact Resistance: 10Ω-500Ω
- Insulation Resistance: 100MΩ 100V
- Key Operating Force: 150-200N
- Circuit Rating: 35V DC, 100mA, 1W
- Dielectric Strength: 250V RMS (50-60HZ/Min)
- Electric Shock Jitter: ï¼ÂÂÂ5ms
- Operating Temperature: -40 deg. C ~ 80 deg. C
- Storage Temperature: -40 deg. C ~ 80 deg. C
- Vibration: 20G, max
- Size: 68mm x 76mm
What's in the box?
1 x 4x 4 Matrix Array Membrane Keypad
Resources
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- Blue Colour
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Gold Plated Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
What's in the box?
1 x Official Sanwa button
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- Red Colour
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Gold Plated Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
What's in the box?
1 x Sanwa Arcade button
They are easy to incorporate into your electronic enclosures, and they provide both a switch and fuse for whatever load.
3 In 1: AC 3P male power plug with an integral switch and fuse holder, Use Only with 250V Fuse. (Fuse is Not Included).
Widely used for your CNC controller box,PC case, instrument, tableware, counter, daily use,etc.
Specifications:
- Voltage: 10A AC250V
- Contact Resistance: ≤0.03Ω
- Withstand voltage: AC 1500V(50hz)/min
- Insulation Resistance: ≥100MΩ
- Insertion and Extrartion Force: 3-20N
- Dielectric intensity: ≥2000V AC/min
- Temperature: -40℃ to 70℃
- Color: Black
Package includes:
1x power supply socket
Features
- Rating: 3A 250V
- Mounting hole: 20mm
- Poles: SPST
- Terminal: 2-Pin(ON-OFF)
- Contact resistance: ≤30mΩ
- Insulation resistance: ≥100MΩ at 500V DC
- Dielectric strength: 1500V AC for 1 minute
- Operating temperature: -25°C - 85°C
- Electrical life: 10000 cycles
- Colour: black / red
What's in the box?
1 x Mini round red rocker switch
Resources
Introduction to Buttons and Switches
Types of buttons and switches
Widely used in various electronic products, instruments, apparatus and home appliances.
- Waterproof Boot
- Model: E-TEN1021
- Sizes: 29 x 16 x 56mm
- Style: On-Off
- Power: 15A 250VAC
- Connector Type: SPST
- Material(External): Metal
- Dielectric strength: 1000 V RMS (min)
- Insulation resistance: 100 Mω(min)
- Basal material: Poly propylene materials
- Mechanical life: More than 50.000 cycles
- Electrical life: More than 10,000 cycles
- Environment temperature: - 25 degrees ~ 80 degrees
- Vibration: 10 to 55Hz, 1.5 mm double amplitude
1 X SPST 2Pin Heavy Duty15A 250V ON/OFF Rocker Toggle Switch Waterproof Boot
Resources
Introduction to Buttons and Switches
Types of buttons and switches
Specifications
- 250 V
- 3A
- 10mm x 15mm
1 x Black Mini Rocker Switch
Resources
Python library
Introduction to Buttons and Switches
Types of buttons and switches
Although the reader does not read the information on the NFC card, it is triggered by a 125 khz NFC card
We designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
Package:
2 x LilyPad Button Board module for ArduinoWe designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
Dimensions:
8mm x 16mm
Thin 0.8mm PCB
Package Includes:
2 x LilyPad Button Board module for Arduino
Getting started with Lilypad button sensor board
Rocker Switches house a button for operation that can be pressed on either end like a seesaw to connect or disconnect an electrical circuit. They are often used as ON/OFF switches on the main power supplies for electronic devices.
Features:
- Rating: 3A 250V
- Mounting hole: 20mm
- Poles: SPST
- Terminal: 2-Pin(ON-OFF)
- Contact resistance: ≤30mΩ
- Insulation resistance: ≥100MΩ at 500V DC
- Dielectric strength: 1500V AC for 1 minute
- Operating temperature: -25°C - 85°C
- Electrical life: 10000 cycles
- Color: black
Package included:
1 x Mini round black rocker switch
Resources:
Introduction to Buttons and Switches
Types of buttons and switches
RASPBERRY PI BOARD NOT INCLUDED
Description:
Whether you're pulling-up or pulling-down, there's no need to frown! With the PUD board from ModMyPi, adding multiple pull-up or pull-down resistors to your Raspberry Pi project is easy!
If you want to detect an "output" with your Raspberry Pi, like a button being pressed or a motion sensor detecting movement, we can configure our Raspberry Pi's GPIO pin as an "input". That input pin can be in three states (known as Tri-State logic); "high", when 3.3V is applied, "low", when the pin is connected to 0V, and "floating" when the state is undefined. Floating voltages are troublesome in electronics as the input can either read high or low depending on various fluctuations in electrical noise. Like a gate flapping open and closed in the wind, someone needs to lock the gate closed, or wedge it open. If you leave it flapping, it's likely to hit someone on their bottom on the way through!
Like our gate, the best way to avoid a floating input is to "tie" your input pin either high or low to create a default state. This is usually achieved through the use of a pull-up or pull-down resistor, either connecting our input pin via a resistor to the Pi's 3.3V to achieve a 3.3V high state, or the GND line to achieve 0V low state.
Our PUD board takes the messy wiring out of adding a pull-up or pull-down resistor to your circuit. Simply wire up the sensor output to the single pin on the PUD board and add a shunt jumper to either pull up (u) or down (d)! Therefore when you apply a signal voltage from your sensor or switch, the Pi is easily able to sense into which logic state the pin has been pulled! No more trouble from floating I/O's!
The PUD boards connects across GPIO pins 11 to 18 (17 to 24 in BCM speak), and adds a jumper configurable pull-up or pull-down resistor to each GPIO pin: 11 (BCM 17), 12 (BCM 18), 13 (BCM 27), 15 (BCM 22), 16 (BCM 23) and 18 (BCM 24). Pin 17 (3.3V) & pin 14 (GND) are used to tie the pins!
The PUD Board Features:
- Add a pull-up or pull-down resistor to your GPIO with the swap of a jumper!
- Compatible with all Raspberry Pi Models Inc. A /B /2/3 & Zero/ZeroW
- Tiny board means it's easy to integrate into any circuit - takes up just 8 GPIO pins
- Connects across GPIO pins 11 to 18 inclusive (BCM 17 to 24)
- In-line 1kΩ current limiting resistors on each GPIO
- 10kΩ pull-up or pull-down resistors on each GPIO
- All 6 GPIO pins can be configured independently
- Includes 6 x 2 Pin Shunt Jumpers & 1 x PUD Board
- Jumper configurable pull-up or pull-down resistor on pins:
- 11 (BCM 17)
- 12 (BCM 18)
- 13 (BCM 27)
- 15 (BCM 22)
- 16 (BCM 23)
- 18 (BCM 24).
- Pin 17 (3.3V) & Pin 14 (GND) are used to tie the pins!
- To pull pin up, connect the jumper across "u" and the center pin
- To pull pin down, connect the jumper across "d" and the center pin
What's in the box:
1 x PUD Board
Tutorials:
This 3 pins toggle switch is great for any project where you have two options to select between. Maybe you'll be selecting between two voltages? Two audio outputs? Two sensor inputs? It's up to you! It's short, sweet, blue, and to the point! The part is marked at 3A 250VAC and 6A 125VAC but we haven't tested it at such high current/voltages and don't recommend it for more than 2A at 24V.
Features
SPDT 3 Terminal ON-ON 2 - Position Latching Toggle Switch.
Each switch is assembled with two hex nuts, a flat and a locking washer.
Easy installation, fits into any 6mm hole.
Stated Electrical Spec: 3A 250VAC or 6A 125VAC, but we recommend using it at 2A at 24V
What's in the box?
1 x 3 pins Toggle Switch
Specifications
- 250 V
- 3A
- 10mm x 15mm
What's in the box?
1 x Mini Rocker Switch
Resources
Python library
Introduction to Buttons and Switches
Types of buttons and switches
Spare key for the isolator switch
This handy switch can be used to disconnect your battery from your projects
Material: Nylon
What's in the box?
1 x battery isolator switch key(spare key only)
This handy switch can be used to disconnect your battery from your projects
Spare keys are available here
What's in the box?
1 x battery isolator switch
If you're into arcade gaming, there's no doubt that you've heard of Sanwa. Used widely in top end arcade arcade machines and manufactured in Japan by Sanwa Denshi Co., Sanwa arcade products are up there at the top of quality chain in arcade gaming. You really can feel the difference in the quality and snappiness of the microswitches!
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
If you're into arcade gaming, there's no doubt that you've heard of Sanwa. Used widely in top end arcade arcade machines and manufactured in Japan by Sanwa Denshi Co., Sanwa arcade products are up there at the top of quality chain in arcade gaming. You really can feel the difference in the quality and snappiness of the microswitches!
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
The Sanwa OBSF-30 range are 30mm "snap-in" style arcade buttons with built in microswitch and 2.8mm terminals. These buttons feature two plastic clips which are designed to lock into panels with a thickness of up to 4mm. They will also clamp perfectly well into greater thickness materials.
Features
- 30mm Diameter Arcade Button
- Sanwa High-Quality Microswitch
- Smooth Clicking Action
- 2.8mm Terminal Contacts
- Official Sanwa Product
- Manufacturer Part No. OBSF-30
What's in the box?
1 x Sanwa Arcade button