Electronic parts
Use this kit as inputs for sensing and outputs for reporting in your projects.
We found a nice tutorial that covers most of the sensors here
Packing List
1 x XY JoyStick
1 x Relay
1 x Big Sound
1 x Small Microphone
1 x Tracking
1 x Avoid
1 x Flame
1 x Linear Hall
1 x Touch
1 x Digital Temperature
1 x Buzzer
1 x Passive Buzzer
1 x RGB LED
1 x SMD RGB
1 x 2-Color LED
1 x 2-Color
1 x Reed Switch
1 x Mini Reed
1 x Heartbeat
1 x 7 Color Flash
1 x Laser
1 x Button
1 x Shock
1 x Rotary Encoders
2 x Magic Cup
1 x Tilt Switch
1 x Ball Switch
1 x Photo resistor
1 x Temp and Humidity
1 x Analog Hall
1 x Hall Magnetic
1 x TEMP
1 x Analog Temp
1 x IR Emission
1 x IR Receiver
1 x Tap module
1 x Light Blocking
We found this article explaining what the sensors are used for: http://www.instructables.com/id/Arduino-37-in-1-Sensors-Kit-Explained/?ALLSTEPS
The bundle is discounted to save you some hard earned cash rather than paying full price for loose components.
Package includes:
1 x BreadBoard 400 tie points
1 x 40-Pin Gray Ribbon Cable (29cm)
1 x GPIO T Board for easy breadboard connection
40pcs chromatic male to male color jumpers
40pcs chromatic color female to female jumpers
40pcs chromatic male to female color jumpers
Durable and reusable
Easy to use
A popular choice for constructing electronic projects
Use for electronic projects as including Raspberry Pi and Arduino projects
Specifications:
Length :10cm
Compatible with 2.54mm spacing pin headers and breadboards
Kit includes:
1 x ribbon of 40pcs male to male jumpers
1 x ribbon of 40pcs female to female jumpers
1 x ribbon of 40pcs male to female jumpers
This useful kit can be used for your electronic projects or repairs.
25 Value x 5pcs = 125pcs (1uF~2200uF)
Package includes:
5 x 47uF 16V
5 x 100uF 16V
5 x 220uF 16V
5 x 470uF 16V
5 x 1000uF 16V
5 x 10uF 25V
5 x 47uF 25V
5 x 100uF 25V
5 x 220uF 25V
5 x 330uF 25V
5 x 470uF 25V
5 x 1000uF 25V
5 x 2200uF 25V
5 x 1uF 50V
5 x 3.3uF 50V
5 x 4.7uF 50V
5 x 6.8uF 50V
5 x 10uF 50V
5 x 33uF 50V
5 x 47uF 50V
5 x 100uF 50V
5 x 220uF 50V
5 x 330uF 50V
5 x 470uF 50V
5 x 1000uF 50V
Resources:
Theory
Introduction
Types
Quantity: 600pcs
Note: Because they are packed manually it is possible to have inconsistencies.
Thank you for your understanding
Resources:
Introduction to Transistors
Different Types of Transistors and Their Working
There are 5 colours 5MM Red Green Yellow Blue White each 100Pcs, total 500Pcs
Parameter:
Working current: 20 (mA)
Working voltage:
- Red: 1.9V-2.1V
- Yellow: 1.9V-2.1V
- Blue:3.0V-3.2V
- Green: 3.0V-3.2V
- White:3.0V-3.2V
- Red:300
- Yellow: 300
- Blue:700-900
- Green: 400-500
- White:12000-14000
- Red: 630-635
- Yellow: 588-590
- Blue:460-465
- Green: 567-570
- White:Color temperature 8000
Package includes:
500 x 5MM LED Diode
Specification:
Color | Size | Wavelength(nm) | Voltage(V) | MCD | Lens color |
Red | 5mm | 620-630 | 1.8-2.3 | 800-1000 | Red diffused |
Yellow | 5mm | 580-590 | 1.8-2.3 | 800-1000 | Yellow diffused |
Green | 5mm | 520-530 | 2.8-3.6 | 800-1000 | Green diffused |
White | 5mm | 6000-6500k | 2.8-3.6 | 14000-16000 | Clear |
Blue | 5mm | 460-470 | 2.8-3.6 | 800-1000 | Blue diffused |
Resources:
Python library
Introduction
Great for electronics prototyping.
Compatible with Arduino and Raspberry Pi projects.
Box size(L*W*H): 17 x 10 x 2.2 cm
Package includes:
1 x Plastic Box (Contains 610 PCS Connector Kit)
Note:
Artificial pick, please allow an error of 2%, thank you.
MQ-2:
Detection concentration: 300-1000ppm(combustible gas).
MQ-3:
Used in motor vehicles and other no drunken drivers homework personnel on-site testing, also used in other places of ethanol vapor detection.
Feature:
Size: 32 x 22 x 27mm
Main chip: LM393, ZYMQ - 3 gas sensors
Working voltage: DC 5V
1, With a signal output instructions.
2, Two-way signal output (TTL level output and analog output)
3, TTL output signal for low level effectively.(when the low output electric signal lights at ordinary times, can be directly by single chip microcomputer)
4, Analog 0 - 5V voltage, the higher the concentration, the higher the voltage.
5, To ethanol steam has a high sensitivity and good selectivity.
6, In June and has long service life and reliable stability.
7, Rapid response recovery features.
MQ-4:
1, Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
2, With a DO switch signal (TTL) output and AO analog signal output;
3, TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module)
4, The analog output voltage, the higher the concentration the higher the voltage.
5, Methane, natural gas has better detection sensitivity.
6, There are four screw holes for easy positioning;
7, Product Dimensions: 32 (L) * 20 (W) * 22 (H)
8, With a long service life and reliable stability
9, Rapid response and recovery characteristics
Electrical properties:
Input voltage: DC5V power (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output :0.1-0 .3 V (relatively clean), the highest concentration of voltage around 4V
MQ-5:
Suitable for home or industrial on LPG, natural gas, coal gas monitoring devices. Excellent resistance to alcohol, smoke interference.
Module Features:
1, Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
2, With a DO switch signal (TTL) output and AO analog signal output;
3, TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module)
4, The analog output voltage, the higher the concentration the higher the voltage.
5, For gas, natural gas has better detection sensitivity.
6, There are four screw holes for easy positioning;
7, Product Dimensions: 32* 20 * 22
8, With a long service life and reliable stability
9, Rapid response and recovery characteristics
Electrical properties:
Input voltage: DC5V power (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output :0.1-0 .3 V (relatively clean), the highest concentration of voltage around 4V
MQ-6:
Suitable for domestic or industrial on LPG (liquefied petroleum gas), butane, propane, LNG (liquefied natural gas) detection devices. Excellent resistance to ethanol vapor, smoke interference.
Module Features:
1, Using high-quality dual-panel design, with power indicator and TTL signal output instructions;
2, With a DO switch signal (TTL) output and AO analog signal output;
3, TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module)
4, 0 ~ 5V analog output voltage, the higher the concentration the higher the voltage.
5, The propane, butane, LPG, LNG has a good detection sensitivity.
6, There are four screw holes for easy positioning;
7, Product Dimensions: 32 (L) * 20 (W) * 22 (H)
8, With a long service life and reliable stability
9, Rapid response and recovery characteristics
Electrical properties:
Input voltage: DC5V power (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output :0.1-0 .3 V (relatively clean), the highest concentration of voltage around 4V
MQ-7:
For home, carbon monoxide detection device environment. Suitable for carbon monoxide and gas detection.
Module Features:
Detection of concentration: 10-1000ppmCO
Loop voltage Vc: <=10V DC
Heater voltage Vh: 5.0V ±0.2V ACorDC(high)
Load resistance: adjustable.
Heater resistance RH: 31ohm ± 3 ohm(room temperature)
Heater power consumption PH: <=350mW
Standard test conditions:
Temperature: 20 degree ± 2 degree
Humidity: 65% ± 5% RH
Standard test circuit: Vc: 5.0V ± 0.1V; Vh(high):5.0V±0.1V
Vh(low):1.5V±0.1V
1, The analog output voltage, the higher the concentration the higher the voltage.
2, The carbon monoxide detection with better sensitivity.
3, There are four screw holes for easy positioning;
4, Product Dimensions: 32 (L) * 20 (W) * 22 (H)
5, With a long service life and reliable stability
6, Rapid response and recovery characteristics
Electrical properties:
Input voltage: DC5V power (current): 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output :0.1-0 .3 V (relatively clean), the highest concentration of voltage around 4V
MQ-8:
Suitable for domestic or industrial hydrogen leak on a monitoring device. Are not subject to ethanol vapor, soot, carbon monoxide and other gases interference.
MQ-9:
For home or factory gas leak detection device, suitable for carbon monoxide, combustible gas monitoring device.
Can test carbon monoxide: 10 to 1000ppm CO
Combustible gas range: 100 to 10000ppm
Module Features:
Loop voltage Vc: <=10V DC
Heater voltage Vh: 5.0V ±0.2V ACorDC
Heater resistance: 31 ohm ± 3 ohm(room temperature).
Heater power consumption PH: <=900mW
Standard test conditions:
Temperature: 20 degree ± 2 degree
Humidity: 65% ± 5% RH
Standard test circuit: Vc: 5.0V ± 0.1V
Vh:5.0V±0.1V
Warm up time: more than 48 hours.
MQ-135:
MQ135 gas sensor is sensitive material used in clean air, low conductivity tin dioxide (SnO2). When the sensor is kept in their environment
The contaminated gas, the conductivity of the sensor with the air pollution gas concentration increases. Using a simple circuit can be changes in the conductivity
Of the concentration of the gas is converted to the corresponding output signal.
MQ135 sensor for ammonia, sulfide, benzene vapor high sensitivity, smoke and other harmful monitor is also very satisfactory. This sensor can detect a
Measuring a variety of harmful gases, is a low-cost sensors for a variety of applications.
Module Applications:
For home, environmental harmful gas detection device, suitable for ammonia, aromatic compounds, sulfur, benzene vapor, smoke and other gases harmful gas detection, gas sensors tested concentration range: 10 to 1000ppm.
Module Features:
Loop voltage Vc: <=24V DC
Heater voltage Vh: 5.0V ±0.2V ACorDC
Load resistance: Adjustable
Heater resistance: 31 ohm ± 3 ohm(room temperature).
Heater power consumption PH: <=900mW
Sensitive body surface resistance Rs:2K ohm - 20K ohm(in 100ppm NH3)
sensitivity S: Rs(in air)/ Rs(100ppmNH3)>=5
Standard test conditions:
Temperature: 20 degree ± 2 degree
Humidity: 65% ± 5% RH
Standard test circuit: Vc: 5.0V ± 0.1V
Vh:5.0V±0.1V
Warm up time: More than 48 hours.
Package includes:
1 x MQ2
1 x MQ-3
1 x MQ-4
1 x MQ-5
1 x MQ-6
1 x MQ-7
1 x MQ-8
1 x MQ-9
1 x MQ-135
1 x 20pcs 20cm male to female jumper cable
1 x 20pcs 20cm female to female jumper cable
Analog to digital converter not included
Configure and read MQ-x gas sensor
Specifications:
Total Length: 7.28m
Shrinkage Ratio: 2:1 (will shrink to 1/2 its supplied diameter)
Material: Polyolefin
Minimum Shrinkage Temp: +70°C
Full Shrinkage Temp: +110°C maximum
Operating Temperature: -55°C to +125°C
Tensile strength: 10.4 Mpa
Dielectric strength: 15 kV/mm
Manufacture specification: ISO9001
Flammability: Flame Retardant
Approvals: UL Approved
Supplied format (round or flat): Product is supplied flat
Cutting method: Scissors or sharp knife
10PCS x 2 Amp | 10PCS x 3 Amp | 10PCS x 5 Amp | 10PCS x 7.5 Amp | 10PCS x 10 Amp |
10PCS x 15 Amp | 10PCS x 20 Amp | 10PCS x 25 Amp | 10PCS x 30 Amp | 10PCS x 35 Amp |
This pack is a great way to get started with E-Textiles.
We have selected a number of products from our Electro-Fashion range, including three of our ultra-slim LEDs and two seperate power boards. There are enough components for you get started immediately to create some eye catching E-Textiles projects, the only limit is your imagination.
Features:
- Everything you need to complete two projects.
- Enough Electro-Fashion components to get started immediately with E-Textiles.
- Full instructions for assembly.
- Great project ideas and tutorials.
Contents:
- 2 x Coin Cell Holder.
- 3 x Sewable LEDs White.
- 3 x Flashing LEDs White.
- 1 x Slide Switch.
- 1 x Push Switch.
- 2 x CR2032 Coin Cell Batteries.
- 1 x 6m Conductive Thread.
Dimensions:
- Sewable Coin Cell Holder Length: 34mm.
- Sewable Coin Cell Holder Width: 20mm.
- Sewable Coin Cell Holder Height: 4.5mm.
- Ultra Slim Sewable LED Length: 15mm.
- Ultra Slim Sewable LED Width: 6.5mm.
- Ultra Slim Sewable LED Height: 2.7mm.
- Slide Switch Length: 18mm.
- Slide Switch Width: 8.5mm.
- Slide Button Switch Height: 4mm.
- Push Button Switch Length: 18mm.
- Push Button Switch Width: 8.5mm.
- Push Button Switch Height: 3mm.
- CR2032 Battery Height: 3.2mm.
- CR2032 Battery Diameter: 20mm.
Requires:
- Scissors.
- Needles.
Resources:
Caution:
- The coin cell holders in this pack contain Nickel and should not be used in designs where it will be in prolonged contact with the skin.
- Enrich children's leisure life, cultivate hands-on ability, and consolidate knowledge.
- Assisting teachers and parents in better physics teaching.
- Let kindergarten children and elementary school students learn physical knowledge, hands-on to form a simple series circuit
Specifications:
- Color: Green+Black (As Picture Show)
- Material: Plastic
- Battery: 2*AA Battery (Not included)
Package Contents:
1 x Bulb Holder
1 x Battery Holder
1 x Switch
1 x Bulb
1 x Conductive Line
(batteries not included)
- A simple solar power experiment kit. - After assembly, put it under the sunlight, the fan blade will rotate through solar energy consumption.
- With this kit you can make an environmental friendly power supply for fan by your self.
- Ideal toy aims for training teen's imagination and eye-hand coordination.
- Ideal choice for developing teens' intelligence.
- Dimensions: Approx.10*4cm
- Power source: Solar energy
Tips:
1. Do not let your kids swallow it as it can cause suffocation.
2. Not suitable for kids under 14 years old.
Package Contents:
1 x Solar power experiment kit
- 25x 0 Ohm ±1%
- 25x 10 Ohm ±1%
- 25x 20 Ohm ±1%
- 25x 47 Ohm ±1%
- 25x 470 Ohm ±1%
- 25x 2.2k Ohm ±1%
- 25x 4.7k Ohm ±1%
- 25x 22k Ohm ±1%
- 25x 47k Ohm ±1%
- 25x 100k Ohm ±1%
- 25x 220k Ohm ±1%
- 25x 470k Ohm ±1%
- 25x 1M Ohm ±1%
- 50x 100 Ohm ±1%
- 50x 220 Ohm ±1%
- 50x 330 Ohm ±1%
- 50x 1k Ohm ±1%
- 50x 10k Ohm ±1%
- 20x 5mm Green LED
- 20x 5mm White LED
- 20x 5mm Yellow LED
- 20x 5mm Red LED
- 20x 5mm Blue LED
- 20x 5mm Pink LED
- 20x 5mm Orange LED
- 20x 5mm Purple LED
- 20x 5mm Green LED
- 20x 5mm White LED
- 20x 5mm Yellow LED
- 20x 5mm Red LED
- 20x 5mm Blue LED
- 20x 5mm RGB LED (slow flash)
- 20x 5mm RGB LED (fast flash)
The kit is accompanied by a set of (currently 6) downloadable worksheets (or lesson plans for you educators!) that will take you through a series of exercises and projects, teaching you how to make the most of your kit. Whats best is that there is no soldering required, each high quality component is breadboard friendly!
All the worksheets are freely available to download from http://camjam.me/edukit
Kit Contents:
- 1 x Breadboard
- 1 x Immersible temperature Sensor
- 1 x PIR Sensor
- 1 x LDR
- 1 x Active Buzzer
- 1 x Red 10mm LED
- 1 x Blue 10mm LED
- 1 x 4.7K Resistor
- 2 x 330 Resistor
- 10 x M/F Jumper Wires
- 4 x M/M Jumper Wires
- 1 x Presentation Tin
Here are just 4 cool projects you could use the kit for:
- Make a burglar alarm for your bedroom.
- Switch on an LED when it gets dark.
- Have an alarm go off when it’s freezing outside.
- Test whether the light really does go off in the fridge when you shut the door.
Still not convinced? Check out these awesome articles on the kit!
- "CamJam Edukit 2 Launches at PiWars" - Raspi.tv
- "The CamJam EduKit 2 - Learn How To Use Sensors With The Raspberry Pi" - Average Man vs Raspberry Pi
The CamJam EduKit is a joint venture between The Pi Hut and the Cambridge Raspberry Jam (CamJam). Profits from the sale of the kit will go to CamJam so that they can continue their educational and community work.
The third in the series is here! The CamJam EduKit #3 is focused on robotics and contains (almost) everything you need to create your very own Raspberry Pi-powered robot.
All you need to do is to add your own chassis, Raspberry Pi (any model) & batteries! Then, follow the worksheets to make your own motorized buggy. Add the included sensors and you will soon be detecting objects in front of your robot and following line courses. Included in the kit are the following components:
- A custom-designed, pre-soldered motor controller board (with screw terminals)
- Two DC motors (with wires pre-soldered)
- Two custom red wheels (which go extra fast… because they’re red!)
- A ball castor (used as the ‘third wheel’ to your robot)
- A small breadboard (to create your circuits)
- Two pieces of strong 3M padded double-sided tape
- A battery box for 4 AA batteries (batteries not included)
- An ultrasonic distance sensor (for detecting objects in front of your robot)
- A line follower sensor (for detecting and following black lines)
- Resistors and jumper cables with which to complete your circuits
- A strong cardboard box to keep it all in… or to cut into to make your chassis!
All the worksheets are freely available to download from http://camjam.me/edukit
Got a 3D printer? Daniel Bull has very kindly designed an awesome chassis, available from Thingiverse ..
Alex Eames over at Raspi.TV got his hands on a prototype, here's what he did!
https://youtu.be/LJDEV7rGwaM
And here's a fantastic unboxing video from Average Man vs Raspberry Pi!
https://youtu.be/KPYWNXiItwo
And another review! This time from TheRaspberryPiGuy! Thanks Matt!
https://youtu.be/TMjd0UrH2PY
Resources:
Intoduction
Basics, Types, Characteristics, Applications & Packages
Dimension: 16.7 x 5.7 x 1cm
Tie Points: 830 tie points (consists of: 630 tie-point terminal strips, 200 tie-point distribution strips)
Matrix: 126 separate 5 point terminals, plus 4 horizontal bus lines (Power Lines) of 50 test points each
Jumper size: Suitable for 20~29 AWG (0.3mm ~ 0.8mm) wires
MB-102 Power Supply Module:
Input voltage: 6.5V ~ 12 V DC / USB power supply
Output voltage: 3.3V / 5V select with jumpers
Maximum output current: <700mA
Fluctuation two road independent control, can switch over to 0V, 3.3V, 5V
On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use
Size: 5.3 x 3.2 x 2.5cm
Jumper Cables:
Breadboard jumper cable male to male
Typically used for electronics projects
Wires are flexible, durable, reusable, easy to trace
Easy to connect and disconnect
Kit includes:
1 x 830 tie point Solderless Breadboard
1 x MB-102 Breadboard Power Supply
65 x Breadboard Jumper Cables male to male