All Products

This 4-wire cable is a little over 150mm long and fitted with JST-SH (Qwiic/STEMMA QT) female 4-pin connector on one end, and female jumper wires on the other.

This 4-wire cable is a little over 300mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

These are handy for extending a Stemma QT or Qwiic cable if you don't have one long enough for your project, or to protect a port if you're regularly swapping out sensors/dev boards. The pin connections are 1-1, matching both sides.

This 4-wire cable is a little over 200mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

The Adafruit VL53L4CX Time of Flight Sensor is another great Time of Flight distance sensor from ST in the VL5 series of chips, this one is great for long distances - it goes up to 6 meters compared with 4 meter max of the VL53L1X.

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around and often have little detents for tactile feedback.

This OLED goes out to all the fans who want more pixels in a smaller size! Normally our 128x64 OLEDs are the biggest ones we've stocked that can use I2C. This one is a whopping 128x128 pixels in crisp monochrome.

Vishay has a lot of light sensors out there, and this is a nice simple lux sensor that's easy to add to any microcontroller. Most light sensors just give you a number for brighter/darker ambient lighting.

The Adafruit LIS3DH Accelerometer Breakout packs low-power consumption, flexible I2C/SPI connectivity, and advanced motion detection into a compact, STEMMA QT-ready board—perfect for wearables, motion sensing, and battery-powered projects.

Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. The SHT41 sensor is the fourth generation of I2C temperature and humidity sensor from Sensirion.

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed.

This Qwiic/STEMMA GPIO connector from Ozzmaker allows you to easily connect Qwiic or STEMMA enabled modules to a Raspberry Pi, without the need for soldering.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Single-cell lithium base battery charger & protection module. The charging will be via a micro B connector. Lithium base battery includes Li-po and Li-ion battery as the charging and discharging characteristic is similar.

The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Raspberry Pi. The SHIM design allows you to plug directly into the Pi's I2C bus with no soldering required and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other HATs!

Non-contact liquid level sensor for Arduino, using a high-speed chip for toxic or high-pressure liquids. Compatible with Gravity interface, with adjustable sensitivity.

Ideal for your dc electronic projects.

The AMS1117-3.3V Step-Down Power Module is a compact, plug-and-play Low Dropout (LDO) linear regulator designed to easily convert a 4.5V–7V input into a stable, clean 3.3V DC output.

Build Your DIY Powered Models, Solar Display and Solar Toys. This 4.5V solar panel is lightweight, and durable