All Products
You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts every 3 seconds or so. It's a very handy tool for testing USB devices, checking load levels and debugging battery chargers and boost converters.
Specifications:- USB 1.x and 2.x - all data speeds. Does not have USB v3 pins so USB v3 connections will automatically downgrade to v2
- Working Range: 0~3A, 3.5~7VDC
- Resolution: 10mV / 10mA
- Operating Temperature: 0-60ºC
- Contents:
- Camera Board 360 Gooseneck Mount V2
Dimensions:
- 21mm x 53mm x 15mm / 0.8" x 2.1" x 0.6"
- USB Plug: 13mm / 0.5"
- Weight: 16.2g
1 x USB Voltage and Current Meter
830 solderless point that allows electronic components to be interconnected in an almost endless number of ways to produce working circuits. Compatible with resistors, transistors, diodes, LEDS, capacitors and other types of electronic components. Ideal for experimenting with circuit design for the Raspberry Pi using the GPIO port.
Specifications:- Model: MB-102
- Color: White
- 830 solderless point
- 1 x 830 Point Solderless Breadboard
RASPBERRY PI NOT INCLUDED - Redesigned case now has sufficient space for heat sinks
The One Nine Design Raspberry Pi Case is a three piece, stylish case designed to keep your Raspberry Pi safe but enable easy access to the GPIO. It comes in three pieces:
- A moulded base, with airflow holes and 55mm spaced M3 mounting holes
- A slot over cover, which fits over the Pi, enclosing it, but leaving all ports like the GPIO free for hacking.
- A cover piece, which clips in and protects the Pi from dust and exposure.
This case also features two slots for holding the Raspberry Pi Camera module!
Specifications:- 3 Piece "Easy-Access" Design
- Embossed Raspberry Pi Logo
- SD Card Access
- Clip Shut Case
- Labelled Ports
- Top & Side Location Camera Holder
- Non Slip Feet
- 55mm M3 Mounting Holes
- Full Gloss ABS Plastic
- External Height: 31mm
- External Width: 64mm
- External Length: 95mm
- ROHS Compliant
- 1 x One Nine Design Case
Description:
Pic is for illustration purposes only.
UTP CAT5E flylead cable. UTP Category 5e Flyleads allows for Fast Ethernet and Gigabit computer networks that require Enhanced Category 5 cabling for voice, data and video. 1m in length
Specifications:
- 1m
- UTP
- CAT5E
Contents:
- 1 x 1M UTP CAT5E Flylead
MODULAR CASE NOT INCLUDED
The Modular Raspberry Pi Case is designed to be fully customisable by the user, and adaptable to suit a range of requirements. The streamlined look, and adaptability makes it perfect for many applications, including: the hobbyist maker, digital signage, industrial protection, living-room & child-friendly media centres, classroom eduction, workshops and many more! All add-ons are designed to be interchangeable and can be added and removed when required.
The USB/HDMI security cover is a dual-use shroud that can be utilised to protect access to all the external inputs and outputs. Two covers can be used simultaneously if only very limited access is required, and “punch-out” access hatches are available for both the Ethernet and Micro USB power port if these inputs are required. Security covers are tamperproof and can only be removed from inside the case.
In addition to protecting the Raspberry Pi ports, the shroud is offset from the body by 12mm. The enables the secure, internal and protected use of up to four nano USB dongles with the cover installed.
Specifications:- Dual-Use - Compatible with Either Set of I/O Ports e.g. HDMI or USB Side
- Secure and Tamper-Proof
- RJ45 & Micro USB Power Breakout Hatches
- Off-Set to Enable the Use & Internal Protection of up to 4 Nano USB Dongles!
- 1 x USB/HDMI Cover
If you want to mount your Modular Raspberry Pi Case to a TV or monitor, we have two mounts available depending on your VESA spacing requirements:
- The VESA Splash (a 4-point 75/100mm mount) (this item)
- The VESA Slice (a minimal 75/100/200mm mount)
- Four bolting points
- MIS-D 75mm & MIS-D 100mm Spacing (M4)
- Great for media & signage applications e.g. hiding a TV or monitor
- Made from laser-cut Perspex
Kit Contents
- 4 x M4 Bolts
- 4 x M4 Washers
Tactile Switches or tact switches are an on/off electronic switch that is only on when there is some pressure put on it or when the button is pressed. As soon as the tactile switch button is released and the pressure has been took off, the circuit is then broken.
Specifications:- Size: (Approx.)12x12x7.3mm
- Life: 100000 times
- Quantity: 5pcs
- Current: 50mA
- Voltage: 12V
- 5 x Push Button Switch
Tactile Switches or tact switches are an on/off electronic switch that is only on when there is some pressure put on it or when the button is pressed. As soon as the tactile switch button is released and the pressure has been took off, the circuit is then broken.
Specifications:- Size: (Approx.)12x12x7.3mm
- Life: 100000 times
- Quantity: 10pcs
- Current: 50mA
- Voltage: 12V
- 10 x Push Button Switch
Piezo Electronic Tone Buzzer Alarm 95DB for Continuous Sound. The piezo sounders are like buzzers. The speaker in the buzzer can be optimized for a single sound, no need to reproduce music.
Specifications:- Color: Black
- Buzzer Type: Piezoelectric
- Sound Pressure Level 85 dB
- Rate Voltage: 12V DC
- Operating Voltage: 3 - 24V
- Max Current Rating 11mA
- Frequency 3900±500Hz
- Drive Method: Drive Circuit Built in
- Mounting Holes
- 1 x 85DB Piezoelectric Buzzer Alarm
- Python library
- Using a Buzzer With a Raspberry Pi
Raspberry Pi not included
This is a Mini Real-Time Clock module, it's design for the Raspberry Pi, but it can also be used with an Arduino.
Simply plug this tiny module into the GPIO header on the Raspberry Pi and away you go!
- DS3231 RTC IC
- Self-adjust 3.3V and 5V
- Size: 14x14x12 mm
Features:
- Smaller
- Work in 3.3V and 5V
- Supported Raspberry Pi and Arduino
- 1x RTC Module
- 1x Battery
These white quarter size breadboards are perfect for small prototyping projects for the Raspberry Pi. With easy clip action on each board rapidly snap extra boards together! Each board is 3.5cm x 4.5cm and has 170 tie points - just enough room to build and test a circuit! Tie points are arranged in 34 x 5 pin rows.
Each board features a self-adhesive backing and a single board will fit alongside the Raspberry Pi inside most cases - two boards will fit within the footprint of the Raspberry Pi. There's also two mounting holes for M2 screws on each board, to anchor them down!
Specifications:- Modular clip function - rapidly snap and unsnap boards and circuits as your project grows
- Self-adhesive backing.
- M2 Mounting Points (screws not included)
- 170 tie points arrange in 34 rows of 5 pins.
- 3.5cm x 4.5cm
- 9.7mm thick, including sticky foam on the bottom
- Weight: 38.9g
- 1x Mini Breadboard
IR (Infrared) sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for use on the Raspberry Pi!
To use, connect pin 3 (all the way to the right) to 5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do any decoding of the signal, just passes the 'raw data' along.
Specifications:- Carrier Frequency: 38kHz
- Transmission Range: 45m
- Directivity: 45°
- Supply Voltage Min: 2.5V
- Supply Voltage Max: 5.5V
- Supply Current: 350µA
- Opto Case Style: Through Hole
- Operating Temperature Min: -25°C
- Operating Temperature Max: 85°C
- Packaging: Each
- Operating Temperature Range: -25°C to 85°C
- SVHC: No SVHC (16-Dec-2013)
- Supply Voltage Range: 2.5V to 5.5V
- Manufacturer: VISHAY MINICAST AGC2
- 1x Infrared Receiver
- Using an IR remote with a Raspberry Pi
PIR sensors, often referred to as, "Passive Infrared" or "IR motion" sensors, enable you to sense motion. Everything emits a small amount of infrared radiation (IR), and the hotter something is, the more radiation it emits. PIR sensors are able to detect a change in average IR levels of their detection zone (e.g. when a human enters a room, that room will increase in temperature slightly) and hence sense motion.
This one's great, as it can be powered via the Raspberry Pi's 5V output, and be read directly from the Raspberry Pi's GPIO input (as the sensor has a digital 3.3V output!)
This PIR includes an adjustable delay before firing (approx 0.5 - 200 seconds), has adjustable sensitivity and two M2 mounting holes! It runs on 4.5V-20V power (or 3V by bypassing the regulator with a bit of soldering) and has a digital signal output (3.3V) high, 0V low. Its sensing range is up to 7 meters in a 100 degree cone.
Specifications:
- Input Voltage: 4.5V - 20V
- Current Draw: <50µA
- Digital Output: 3.3V (High)
- Digital Output: 0V (Low)
- Working Temperature: -15°C to 70°C
- Delay Time: 0.5 - 200 Seconds
- Sensing Angle: 100° Cone
- Range 5m - 7m
Dimensions:
- Sensor Lens Diameter: 23mm
- Length: 24.03mm
- Width: 32.34mm
- Height (with lens): 24.66mm
- Centre screw hole distance: 28mm
- Screw hole diameter: 2mm (M2)
- 1x HC-SR501 Motion Sensor
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances! These 1-wire digital temperature sensors are fairly precise (±0.5°C over much of the range) and can give up to 12 bits of precision from the onboard digital-to-analog converter. They work great with any microcontroller using a single digital pin, and you can even connect multiple ones to the same pin, each one has a unique 64-bit ID burned in at the factory to differentiate them. Usable with 3.0-5.0V systems.
The only downside is they use the Dallas 1-Wire protocol, which is somewhat complex, and requires a bunch of code to parse out the communication. If you want something really simple, and you have an analog input pin, the TMP36 is trivial to get going.
We toss in a 4.7k resistor, which is required as a pullup from the DATA to VCC line when using the sensor.
Specifications:Cable specs:
- Stainless steel tube 6mm diameter by 30mm long
- Cable is 36" long / 91cm, 4mm diameter
- Contains DS18B20 temperature sensor
- If your sensor has four wires - Red connects to 3-5V, Black connects to ground and White is data. The copper wire is soldered to the wire shielding
- If your sensor has three wires - Red connects to 3-5V, Blue/Black connects to ground and Yellow/White is data
DS18B20 Technical specs:
- Usable temperature range: -55 to 125°C (-67°F to 257°F)
- 9 to 12 bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to 85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
- 1 x DS18B20 Digital temperature sensor
- 1 x 4.7k resistor
- Adafruit's Raspberry Pi Lesson: DS18B20 Temperature Sensing
This is an eight channel 5V DC relay module with active low. It can be controlled by variety of microcontrollers such as Arduino, Raspberry Pi, PIC, DSP, AVR or ARM etc.
- Has the ability to control eight separate appliances or pieces of equipment
- Eight on-board optoisolators enable direct interfacing to microcontrollers
- Eight red LED status lights on-board show relay activity
- Widely used in PLC control or smart home control
- 4 x M3 mounting holes for easy fixing via standoffs
- 15-20mA drive current needed per channel
- Relay coil maximum operating voltage: 5V
- Relay coil maximum current: 89.3mA
- Relay contact maximum: AC250V at 10A or DC30V at 10A
- No. of relays/channels: 8
- Item size: 134 x 55 x 20mm
- Item weight: 116g
- 1 x 8 Channel Relay Module
Warning
Exercise proper caution when connecting mains driven equipment or appliances to relay module as lethal current will be present.
Description:
These male to male breadboard jumper wires provide an easy way for you to build your own circuitry on a breadboard. These cables are flexible with both ends of a prototyping board connector. The jumper wire is ideal for creating circuits between your microcontroller and breadboard.
Specifications:
Random colours: white, yellow, orange, blue, black and red (as shown in picture)
- Material: plastic tin plated copper
- Outer Diameter: 0.643mmNominal Wire Area: 0.3247 sq. mm
- 4 x 175mm wires
- 4 x 230mm wires
- 8 x 125mm wires
- 49 x 95mm wires
Contents:
- 1 x Pack of 65 x Jumper Wires for MB102 Solderless Breadboard
Resources:
This flexible 4x4 matrix keypad is connected to an 8 pin DuPont Female connector. It can be attached to a surface via the adhesive back by removing the white protective paper backing.
Specifications:- Contact Resistance: 10Ω-500Ω
- Insulation Resistance: 100MΩ 100V
- Key Operating Force: 150-200N
- Circuit Rating: 35V DC, 100mA, 1W
- Dielectric Strength: 250V RMS (50-60HZ/Min)
- Electric Shock Jitter: ï¼ÂÂÂ5ms
- Operating Temperature: -40 deg. C ~ 80 deg. C
- Storage Temperature: -40 deg. C ~ 80 deg. C
- Vibration: 20G, max
- Size: 68mm x 76mm
- 1 x 4x 4 Matrix Array Membrane Keypad
Raspberry pi 40 pin Female to female flat ribbon cable specifically designed to fit directly onto the GPIO Headers pins of the Raspberry Pi.
Specifications:- 40 pin
- Female to female
- GPIO Header connector
- 20cm long
1 x Female to Female ribbon Cable
400 Point solderless breadboard. Perfect for solderless electronic projects.
Specifications:- 400 tie points total: 300 tie-point IC-circuit area plus two 50 tie-point distribution strips providing 4 power rails.
- White ABS plastic body with black printed legend.
- Color legend on distribution strips.
- Size: 3.3 x 2.1 x 0.3in (84 x 54.3 x 8.5mm).
- Peelable adhesive tape backing provided for attaching to a surface.
- 1 x 400 Point Breadboard