All Products

Sort By:  
Protect your Pi Zero 2 W in style with the Pibow Zero 2 W case, in calming violet waters - ocean blue, purple, and deep blue!
R109.90  Inc VAT
DIY Foam Ball Launcher STEM Kit (DIY foam ball launcher)

Note: This kit comes with 4x AA batteries.

Note: Download the softcopy instruction manual (English) here

Images are for references only


The DIY (Do It Yourself) Kit for Children Age 4 to 12 Years Old

Have you seen a tennis ball launcher? No? Well, in this kit, you will learn how to build your very own ball shooter! But instead of using a tennis ball, you will be shooting with a foam ball with extreme speed! While building the launcher, you will also learn how to connect a DC motor with hook up with wheels which creates friction on the foam to launch it forward.


  • Do It Yourself Foam Ball Launcher
  • Suitable for age 6 years old and above
  • Come with everything needed to assemble the launcher project
  • AA batteries included
  • Learn about DC motor and the concept of friction on different objects and surfaces
  • Be able to launch paper balls and various materials (Not included in the kit)

Packing List:

  • Wooden parts for the launcher structure
  • Some double-sided tape
  • Some screws
  • 2 x orange stopper
  • 1 x AA battery holder
  • 1 x DC motor
  • 1 x Metal rod
  • 2 x Wheel
  • 1 x Big metal bracket
  • 2 x Small metal bracket
  • 5 x Circular foam
  • 1 x Screwdriver


R79.90  Inc VAT
DIY Wire Loop Circuit Detector (without Batteries) (DIY wire loop circuit )

Note: This kit DOES NOT INCLUDE the AA batteries for you to get started without hassle.

Note: Download the softcopy instruction manual (English) here
Images are for reference only


The DIY (Do It Yourself) Kit for Children Age 4 to 12 Years Old

Get this kit to keep your kids occupied with hands-on activities while enjoying the buzzing while keep your hand steady moving through the wire. This DIY kit is simple enough to be built by 4 years old children, with parent's help. And children 6 years old and above can build it by themself! Let's them explore the fundamental electric circuit. When the circuit is complete (touches the wires), the current will drive the load (in this case is the buzzer).

Your kids can always follow the video to build the robot or if you prefer the step by step guide in a document, we have also produced an instruction manual in English:

Note: Not suitable for children under 4 years old!


  • Do It Yourself simple Buzz Wire Game for kids
  • It can really buzz!
  • Suitable for age 4 years old and above
  • Come with everything needed to assemble as a working game
  • Powered with two (2) AA-size batteries (not included in this kit)
  • No soldering is needed
  • Great family hands-on activity

Packing List:

  • 1 x Connector Base
  • 2 x Pink Straw
  • 2 x Green connector
  • 2 x Red LED
  • 1 x 2xAA size battery holder with wires (Black and Red)
  • 1 x Buzzer
  • 1 x metal cable
  • Some screws
  • 1 x Heat Shrink Tube


R59.90  Inc VAT
ArduCam 16MP IMX519 Autofocus Camera Module for RPi and Jetson (Arducam 16MP)

Arducam High-Resolutions Autofocus camera is an exclusive camera board that takes what Raspberry Pi V1, V2, and HQ have to offer, and excels in every single aspect.

It takes zero compromises in specs. With a resolution of 16 megapixels (compared to 8MP and 12MP), an autofocus lens, a V2-like form factor, and boatloads of improvements, the camera provides a better choice for a whole world of industrial/consumer/etc. applications, it’s compatible with any existing Pi models, works with the latest software from the foundation, and leverages the same tuning algorithms used in the official camera modules.

Check out this  review by Jeff Geerling and his video

16MP Camera Module for All Pis.

2 times higher resolution than the v2 camera, 40% higher than the HQ camera. Based on the 16MP Sony IMX519 sensor, this new camera module gives all Raspberry Pi hackers every bit of power they need to build future-proof projects.

V1/V2 Size, with Autofocus.

The community has been craving autofocus in Pi cameras, so Arducam took the advice. This camera has the classic V1/V2 form-factor so you can add hassle-free upgrades to your existing projects, or build new applications with the best flexibility on cameras.

Crisper Images/Videos Than The HQ Camera.

It’s not just the resolution bump, the “quality” is way higher than the HQ Camera too. With the same camera tuning algorithms from the foundation, this module beats the Raspberry Pi HQ camera in every aspect. (sharpness/saturation/exposure/etc.)

Safety instructions:

  • Before connecting, you should always power the Raspberry Pi off and remove the power supply first.
  • Make sure the cable on the camera board is locked in place.
  • Make sure the cable is correctly inserted in the Raspberry Pi board’s MIPI CSI-2 connector.
  • Avoid high temperatures.
  • Avoid water, moisture, or conductive surfaces while in operation.
  • Avoid folding, or straining the flex cable.
  • Avoid cross-threading with tripods.
  • Gently push/pull the connector to avoid damaging the printed circuit board.
  • Avoid moving or handling the printed circuit board excessively while it’s in operation.
  • Handle by the edges to avoid damages from electrostatic discharge.
  • Where the camera board is stored should be cool and as dry as possible.
  • Sudden temperature/humidity changes can cause dampness in the lens and affect the image/video quality.



  • Sensor: Sony IMX519 stacked, back-illuminated sensor 16 megapixels 1.22 µm × 1.22 µm pixel size7.103 mm diagonal (Type 1/2.534)
  • Output: RAW10/8, COMP8
  • Lens: Autofocus;  f/1.75; EFL: 4.28; FoV: 80°; Focus Range: 10 cm ~ infinite
  • IR cut Filter: Integrated
  • Tripod mount: 1/4”-20
  • Enclosure: ABS, also compatible w/ camera module v1 & v2.
  • Ribbon Cable Length: 150mm


What's in the box?

  • 1 x ArduCam 16MP IMX519 Autofocus Camera Module for RPi with case
  • 1 x 15cm ribbon cable



R689.90  Inc VAT
Pibow Zero 2 W (Pibow zero 2 W)

Protect your Pi Zero 2 W in style with the Pibow Zero 2 W case, in calming violet waters - ocean blue, purple, and deep blue!

Note: this case is for the Raspberry Pi Zero 2 W only. This case is not compatible with the Pi Zero or the original Pi Zero W. Does not include a Raspberry Pi Zero 2 W!

We've got a tutorial showing you how to build your Pibow here.


  • Compatible with Raspberry Pi Zero 2 W
  • Super-slimline profile
  • Fully HAT/pHAT compatible
  • Protects your beloved Pi Zero 2 W!
  • Clear top leaves Raspberry Pi Zero 2 W visible
  • GPIO cut-out
  • Leaves ports and GPIO accessible (encloses micro SD)
  • Slot for camera cable to slip between layers
  • Made from lightweight high-quality cast acrylic
  • Great for hacking and tinkering!
  • Made in Sheffield, UK

Crafted out of four unique layers including a transparent top and base that leave your beautiful Pi visible inside. Each layer is laser-cut from colourful high-quality cast acrylic and once stacked they securely contain a Raspberry Pi Zero 2 W while leaving the primary ports and GPIO accessible.

This case is lightweight and ideal for mounting to any surface. No tools are required for assembly or disassembly!

What's in the box?

1 x Pibow case for Zero 2 W

Protect your Pi Zero 2 W in style with the Pibow Zero 2 W case, in calming violet waters - ocean blue, purple, and deep blue!
R109.90  Inc VAT
Raspberry Pi 4 2 layers acrylic open GPIO Case with fan and grill (Pi4 open GPIO case)
Please Note: Raspberry Pi 4 is not included


Two-part Raspberry Pi case
Easy access to all Pi connectors
Open design to keep your Raspberry Pi cool

What's in the box?

1 x DIY 2-layer Acrylic Case
1 x fan with mounting screws
1 x fan grill
4 x standoffs with screws/nuts
R119.90  Inc VAT
Round Panel Mount Latch Push Button (Red) (red latch button)

General purpose 'push-to-on button', self latch on push button. Single Pole Single Throw (SPST), normally open type. Press to connect and it will latch on itself. To disconnect, press the push  when released.

Features and Spec:

  • Normally Open (NO) type
  • Contact rating :125VAC 3A
  • Switch type: Push and lock
  • Weight: 10g
  • Material: Plastic (body and button)
  • Button color: Red
  • Pitch : 3mm
  • Thread diameter: 12mm
  • Button diameter: 9mm
  • Height: 25mm (body height excluding terminal)

What's in the box?

1 x Round Panel Mount Latch Push Button (Red)
R15.90  Inc VAT
Dual USB 5V 2.4A Type-C LED USB Mobile Power Bank 18650 Charging Module (mobile power bank charging)

This module is the perfect starting point if you are looking to build your own power bank.

This module is ideal for 18650 batteries, 65mm long with the flat top. In the event that you use:
  • old batteries
  • different capacities
  • differnet brands
Please ensure that they are at least above 3.5V each

Not ideal to be used on batteries that have been too far depleted.

After the battery is installed, plug in the charger to activate the battery before use.

The real world conversion rate of a new "real capacity" battery is about 80%. Because ther is a line loss of the connection line. Estimation of mixed batteries or "budget" batteries are near impossible to estimate.

For peak use, first allow the battery to fully discharge before charging it.

Note: Reversing the polarity of the battery will burn the module.


  • Switch Charging
  • Internal 2A charging current
  • Charging efficiency up to 90% @ 2A
  • Charging swtch frwquency 1MHz
  • Trickle/constant current/constant voltage three-stage charging
  • Charging current Adaptive adapter function
  • Charging current Temperature adjustment function, charging current automatically decreases with the increase of temperature
  • C/10 charging terminates
  • Intergrated charge overvoltage protection and battery overtemperature protection
  • Synchronous boost output 5.1V
  • Discharge switch frequency 50OKHz
  • Discharge efficiency up to 94%
  • Automatic identifiation of load, load automatically shut off
  • Original boost output heat regulation function
  • Protection of over current, short circuit, over voltage and over tepmperature of discharge module
  • Long press the switch, wake up the motherboard, charge the charging time of the phone, press the switch, the output can be turned off, the motherboards stops working.
  • MaIn board size: Thickness 9 * Width 25 * length 67 mm

What's in the box?

1 x Power bank type charging module
R99.90  Inc VAT
Maker Reflect: Simplifying IR Reflectance Sensor for Beginner (maker reflect)

Maker Reflect is a tiny reflectance sensor that consists of an infrared (IR) LED that transmits IR light onto a surface and a phototransistor measures how much light is reflected back. The output is in analog voltage - The more IR light is sensed by the phototransistor, the lower the voltage.

Typically this sensor is used in line following robot as the white surfaces reflect more IR than black surfaces. However, it is not limited to line follower, there are much more application which can utilize the Maker Reflect. Eg.: Edge/Border sensor in Sumo robot, wall sensor in maze solving robot, short-distance object detector (presence sensor), a sensor for rotary wheel encoder...etc.

Measuring only (L)18.1mm x (W)8.4mm x (H)4.2mm (Exclude the header pin), this tiny sensor can be easily fitted in the tightest space available on your robot. We purposely designed the sensor so that the mounting hole is at the center so that the sensor can be at the front-most position. This is especially important in the Sumo robot.


  • Operating Voltage: 3.3V and 5V Compatible
  • Sensing Distance (Height): 1mm to 40mm (Vcc = 5V, Black line on a white surface)
  • Output: Analog Voltage (White surface = lower voltage)

Example Application: Line Following Robot, Sumo Robot, Wall Following Robot, Short Distance Object Sensing, Sensor for Printed Rotary Wheel Encoder.


What's in the box?

R34.90  Inc VAT
MK8 0.4mm Copper M6 Thread Extruder Nozzle For 3D Printer (MK8 print nozzle 0.4mm)

Original 0.4mm Copper M6 Thread Extruder Nozzle For Ender-3 CR-10 V2 CR-10S Pro Ender-5 CP-01 CREATITY 3D


1. Material: Copper
2. Size: 13mm x 6mm
3. Weight: 2g
4. Nozzle thread: M6
5. Nozzle accuracy: 0.4mm

What's in the box?

1 x 0.4mm Nozzle

R16.90  Inc VAT
0.4 mm MK8 Nozzles & 10PCS 0.4 mm Needles &1PCS Tweezer Stainless Steel Nozzle Cleaning Tool Kit For 3D Printer (nozzles, needles, tweezer cleaning kit )

3D printer extruder nozzles:

The 3D printer nozzles are made of fine quality brass material, sturdy and durable; Compatible with 3D printer Makerbot Creality CR-10, MK8 Makerbot Reprap Prusa I3, and fit for all 1.75 mm PLA ABS 3D printer.

Stainless steel needles:
10 Pieces of 0.4 mm diameter needles are made of flexible stainless steel, and it is good for gentle maintenance of your nozzles and hard-to-reach places like the feed gears.

3D printing tweezers are good for nozzle maintenance and cleaning excess support material.
It is anti-static, non-magnetic curved precision tweezers.

Color: gold
Material: brass
Hexagon diameter: 6 mm
Screw thread: M6
Input diameter: 1.75 mm
Output diameter: 0.4 mm
Quantity: 10 pieces in total

Package contents:
10 x 0.4 mm Nozzle print head
10 x 0.4 mm Needles in bottle
1 x Tweezers

Warm notes:
Small parts, please keep away from children.
R127.90  Inc VAT
Nano Base Board (B) for Raspberry Pi Compute Module 4 (nano base for CM4)
Note: the CM4 is NOT included. Please buy it separately if necessary.


The Nano Base Board (B) For Raspberry Pi Compute Module 4, is the Same Size As The CM4 and is suitable For Evaluating The Raspberry Pi CM4 Or Being Integrated Into End Products.

This module is Compact, Yet Complete, featuring: Standard CM4 Socket, 40PIN GPIO, Gigabit Ethernet, USB2.0, DSI, CSI, 3.5mm Audio Jack...


CM4 SOCKET    -      suitable for all variants of Compute Module 4
NETWORKING  -      Gigabit Ethernet RJ45 connector
CONNECTOR    -      Raspberry Pi 40PIN GPIO header × 1
USB                      -      USB 2.0 Type A connector × 1
DISPLAY             -       MIPI DSI port × 1 (15pin 1.0mm FPC connector)
CAMERA            -       MIPI CSI-2 port × 1 (15pin 1.0mm FPC connector)
VIDEO                 -       Mini HDMI port × 1, supports 4K 30fps output
AUDIO                -       3.5mm jack
STORAGE          -        Micro SD card socket for Compute Module 4 Lite (without eMMC) variants
POWER INPUT    -    5V
DIMENSIONS       -    56 × 41mm

What's On Board

CM4 socket   -   suitable for all variants of Compute Module 4
Micro SD card slot   -    for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)
40PIN GPIO header   -    for connecting sorts of HATs
Gigabit Ethernet RJ45 connector
Power supply / Programming  -   5V power supply, or used for eMMC burning
3.5mm audio jack
User button
USB2.0 connector  -   for connecting sorts of USB devices
CSI connector  -   MIPI CSI camera interface
DSI connector  -   MIPI DSI display interface
Mini HDMI connector  -  supports 4K 30fps output
BOOT switch: 
  • ON: Switch USB to Type C interface, will enter download mode when powered on (configured as a large-capacity disk through RPI boot)
  • OFF: Switch USB to Type A interface, will not enter download mode when powered on (booted from eMMC or Micro SD card)

Outline Dimensions

What's in the box?

1 x CM4-NANO-B

1 x 2*20PIN color-coded straight pin header

Resources & Services

R319.90  Inc VAT
3 in 1 Clip-On Camera Lens Set (camera lens clip-on kit)


This lovely little lens set is the best way to easily expand the field of view of your Raspberry Pi camera!

This lens kit means that you can use your camera module in many exciting ways:

  • 1x Wide-angle lens: Ideal for capturing those landscape shots/night sky time-lapses
  • 1x Macro lens: Beautiful close-up images of anything from insects to circuit boards
  • 1x Fish-eye lens: Security systems and crazy 180° FOV shots

Perfect for taking shots from anywhere from your desk to the edge of space this lens comes with a back splint which means you can also use it with other camera devices such as your mobile phone.

Each lens screws into the clip which fits perfectly onto your camera module.


  • Compatible with the known universe *
  • High-class glass lens, high clarity.
  • No vignetting or dark circle.
  • Lens covers to protect the camera lenses
  • Material: ABS & aluminum alloy
  • Compatible with most of the official Raspberry Pi Camera Modules

What's in the box?

1 x camera clip
3 x screw on lenses

R199.90  Inc VAT
HAT - Grove Base for Raspberry Pi (RPi grove base HAT)

Today, the grove series of sensors, actuators, and displays have grown into a large family. More and more grove modules will join the whole Grove ecosystem in the future. We see the Grove helps hundreds of thousands of makers, engineers, teachers, students, and even artists to learn, to make, to create... Now we bring you the Grove Base Hat for Raspberry Pi to make the Grove module compatible with more platforms. In another word, we bring the Raspberry Pi the whole Grove System.

The Grove Base Hat for Raspberry Pi provides a Digital/Analog/I2C/PWM/UART port to meet all your needs. With the help of the build-in MCU, a 12-bit  8 channel ADC is also available for Raspberry Pi. Currently, more than 60 groves have supported the Grove Base Hat for Raspberry Pi.

Compared with Grove Pi , the Grove Base Hat for Raspberry Pi does not use the ATMEGA chip for data conversion, so it runs faster. We provide the Raspberry Pi driver for Grove Base Hat for Raspberry Pi. What's more, Grove Base Hat for Raspberry Pi is much more cost-effective. In other words, we lowered the threshold for using the grove series on the Raspberry Pi. We hope you like it, enjoy :D


  • GPIO:
    The same pinout as the raspberry pi.
  • PWM(pulse-width modulation):
    The Grove PWM Port connects to GPIO/BCM pin12(PWM0) and GPIO/BCM pin13(PWM1), which is the hardware PWM pin of Raspberry Pi, in addition, you can use all the GPIO pins as the soft PWM pin.
  • UART: 
    The Grove UART port connects to the GPIO14(UART0 TX) and GPIO15(UART0 RX). UART is commonly used on the Pi as a convenient way to control it over the GPIO or access the kernel boot messages from the serial console (enabled by default).It can also be used as a way to interface an Arduino, bootload ATmega, ESP8266, etc with your Pi.
  • Digital: 
    There are 6 digital Grove sockets in this board, normally the yellow wire(which connect to the top pin of the 4 pins Grove socket as) of Grove cable is the signal wire, so we name the digital Grove port D5/D16/D18/D22/D24/D26.
  • Analog: 
    As we know, there is no ADC in the Raspberry Pi, so it can not work with analog sensors directly. Now with the help of the build-in MCU STM32, the Grove base HAT can work as an external 12-bit ADC, which means you can use the analog sensor with your Raspberry Pi. Even more pleasing is that not one but four analog Grove sockets are available.
    The analog sensor inputs the analog voltage into the 12-bit ADC. After the ADC converts the analog data to digital data, it input the digital data to the Raspberry Pi through the I2C interface.
  • I2C: 
    There are three I2C ports available in this board, they all connect to the I2C pin of the raspberry directly. You can consider this part as an I2C hub. Most of Seeed's new grove modules have an I2C interface, you may find those I2C three ports are extremely useful.
  • SWD: We use the SWD port to burn the firmware to this hat. In addition, you can see 3 GPIO pins in this section, i.e., pin 9/pin 10/pin 11. Those three pins do not use by any Grove port, you are free to use them without worrying about pin conflicts.


  1. All the silkscreen layer pin number beside the Grove port is the BCM pin number. The difference between BCM pins and the physical pins please refer to here.
  2. Compared with hardware PWM, the software PWM isn't so accurate and will have trouble at high frequencies.
  3. The GPIO/BCM pin18 is also marked as PWM0. The GPIO/BCM 12 and the GPIO/BCM 18 share the same PWM channel, so they can't be set to different rates.
  4. The audio jack output also uses PWM 0 and PWM 1, so you can't have an audio output on that socket and use the PWMs at the same time.
Features and specifications:
  • Support Raspberry Pi 2B, 3B, 3B and 4
  • build-in MCU
  • 12-bit ADC
  • Multi-type Grove port
  • Operating Voltage: 3.3V
  • MCU: STM32/MM32
  • ADC: 12-bit 8 channel
  • Grove Ports:
    • 6 x Digital
    • 4 x Analog
    • 3 x I2C
    • 1 x PWM
    • 1x UART
  • Raspberry pi communication bus: I2C
  • I2C Address: 0x04/0x08


Packing list:
  • 1 x HAT - Grove Base for Raspberry Pi

R289.90  Inc VAT
Grove Base Kit for Raspberry Pi (grove base kit for pi)

The Grove Base Kit for Raspberry Pi is one of the best kits for beginners to get started with Raspberry Pi. No troublesome soldering and no complicated wiring. You can focus on learning Raspberry Pi. This kit includes a Grove Base Hat for Raspberry Pi and 10 Grove modules, which covering the sensor, actuator, and display. All you need to do is following the demo, plug the module into the Grove Base Hat, truly plug and play.

On top of that, we have provided you with detailed instructions on the use of Raspberry Pi and the use of each module, which including 8 lessons for the module. Just click the wiki to view the user manual. Also, you can check the video guide here, which will tell you how to use this kit step by step.

All in all, whether you are a student, teacher, artist, hardware enthusiast, and so on, with the help of the Grove Base Kit for Raspberry Pi,  you will get to know Raspberry Pi quickly and comprehensively.

For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your use of the product.


  • A great kit for Raspberry Pi beginner to get started
  • With Grove modules, no wiring is necessary
  • Plug and Use module
  • Include 10 Grove modules and a Grove base for Raspberry Pi

Now the kit comes with the Grove Base Hat for Raspberry Pi, making Raspberry Pi compatible with the Grove System.

The Grove Base Hat for Raspberry Pi provides Digital/Analog/I2C/PWM/UART port to meet all your needs. With the help of build-in MCU, a 12-bit 8 channel ADC is also available for Raspberry Pi.

Grove Base HAT Features:

Packing List:

  • 1 x Grove Base Hat for Raspberry Pi
  • 1 x Grove - Red LED Button
  • 1 x Grove - Buzzer
  • 1 x Grove - Moisture Sensor
  • 1 x Grove - Temperature & Humidity Sensor (DHT11)
  • 1 x Grove - Light Sensor
  • 1 x Grove - mini PIR motion sensor
  • 1 x Grove - Ultrasonic Ranger
  • 1 x Grove - Relay
  • 1 x Grove - Servo
  • 1 x Grove - 16 x 2 LCD (White on Blue)


R799.90  Inc VAT
800×480, 7.5inch E-Ink display HAT for Raspberry Pi (7.5inch e-ink for pi)
  1. It usually takes about 0.3s for partial refresh
  2. Pi Header: standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards


This is an E-Ink display HAT for Raspberry Pi, 7.5inch, 800×480 resolution, with embedded controller, communicating via SPI interface.

Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.

  • No backlight, keeps displaying last content for a long time even when power down
  • Ultra low power consumption, basically power is only required for refreshing
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
  • SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
  • Onboard voltage translator, compatible with 3.3V/5V MCUs
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)
  • Operating voltage: 3.3V~5V
  • Interface: SPI
  • Outline dimension: 170.2mm × 111.2mm
  • Display size: 163.2mm × 97.92mm
  • Dot pitch: 0.205 × 0.204
  • Resolution: 800×480
  • Display color: black, white
  • Grey scale: 2
  • Full refresh time: 5s
  • Refresh power: 38mW(typ.)
  • Standby power: <0.017mW
  • Viewing angle: >170°
Revision History

Revision V2 has been released on 2019.11, the resolution is upgraded to 800×480, from 640×384 of V1. The hardware and interface of V2 are compatible with V1, however, the related software should be updated.

CSSPI chip selection, low active
DCData/Command selection (high for data, low for command)
RSTExternal reset, low active
BUSYBusy status output, low active

7.5inch e-Paper HAT dimensions
What's in the box:

  1. 7.5inch e-Paper x1
  2. e-Paper Driver HAT x1
  3. RPi screws pack (2pcs) x1
  4. PH2.0 20cm 8Pin x1
1 2  3  4

Development Resources:

Wiki :

R1,159.90  Inc VAT
7.5inch E-Paper E-Ink Display Module for Raspberry Pi Pico, 800×480, Black / White, SPI (7.5inch e-paper for pico)

7.5inch E-Paper E-Ink Display Module For Raspberry Pi Pico, 800×480 Pixels, Black / White, SPI Interface. Low Power, Wide Viewing Angle, Paper-Like Effect Without Electricity. Ideal for price tags, shelf labels, industrial instruments...
    Features At A Glance
    • No backlight, keeps displaying last content for a long time even when power down
    • Ultra low power consumption, basically power is only required for refreshing
    • SPI interface, requires minimal IO pins
    • 2x user buttons and 1x reset button for easy interacting
    • Comes with development resources and manual (Raspberry Pi Pico C/C and MicroPython examples)

    RESOLUTION800×480 pixelsGREY SCALE2
    OUTLINE DIMENSIONS170.2 × 111.2mmDISPLAY SIZE163.2 × 97.92mm
    REFRESH POWER26.4mW (typ.)STANDBY CURRENT<0.01uA (almost none)
    DOT PITCH0.204 × 0.204mm  

    Advantages Of EINK

    E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper.
    E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180° viewing angle. It is usually used as e-reader due to its paper-like effect.

    Raspberry Pi Pico Header Compatibility

    Onboard Female Pin Header For Direct Attaching To Raspberry Pi Pico
    2x User Buttons And 1x Reset Button For Easy Interacting

    Stackable Design

    Extended Pico Header, Allows Attaching More Modules For Pico

    Raspberry Pi Pico and other modules are NOT included.
    Widely Compatible Driver Board

    Onboard Switch For Using With Multi E-Paper Displays, Or Selecting SPI Bus

    Pinout Definition:

    Outline Dimensions


    What's in the box?

    1. 7.5inch e-Paper x1
    2. Pico-ePaper-Driver-Board x1
    3. Standoff pack x1
    1  2 3

    Resources & Services

    R1,129.90  Inc VAT
    Plusivo BJT Transistors Assortment Kit (Plusivo transistor kit)

    This is the perfect kit for experimenting with transistor, it includes the most common PNP and NPN transistors: 2N3904, 2N3906, S8050, 2N2907, S8550, 2N2222, BC337, C1815, BC327, A1015.

    With this 210 pcs bipolar transistor pack you will never have to worry about not having the right transistor for your circuit. The transistor kit comes with a 250 pcs bonus resistor assortment kit that includes the most commonly used resistor values, always useful for your electronic circuits.

    Having a well-designed transistor kit on hand means no more guesswork and frustration when designing and testing your circuits.
    You can depend on it to always find the transistors you need.


    • A transistor kit that includes most commonly used transistor types.
    • A complete transistors assortment kit, so that you always have the PNP and NPN transistors you need.
    • A premium BJT transistor kit that is easy to store and use. It comes with an organizer box.

    What's in the box?

    • 1 x 10 compartments plastic box
    • 21 x Transistor 2N3904
    • 21 x Transistor 2N3906
    • 21 x Transistor S8050
    • 21 x Transistor 2N2907
    • 21 x Transistor S8550
    • 21 x Transistor 2N2222
    • 21 x Transistor BC337
    • 21 x Transistor C1815
    • 21 x Transistor BC327
    • 21 x Transistor A1015
    • Bonus Pack: (in paper box)
      • 10 x Resistor 47 Ω
      • 10 x Resistor 100 Ω
      • 10 x Resistor 220 Ω
      • 10 x Resistor 330 Ω
      • 10 x Resistor 470 Ω
      • 10 x Resistor 680 Ω
      • 10 x Resistor 1 kΩ
      • 10 x Resistor 2.2 kΩ
      • 10 x Resistor 3.3 kΩ
      • 10 x Resistor 4.7 kΩ
      • 10 x Resistor 6.8 kΩ
      • 10 x Resistor 10 kΩ
      • 10 x Resistor 22 kΩ
      • 10 x Resistor 33 kΩ
      • 10 x Resistor 47 kΩ
      • 10 x Resistor 68 kΩ
      • 10 x Resistor 100 kΩ
      • 10 x Resistor 330 kΩ
      • 10 x Resistor 470 kΩ
      • 10 x Resistor 680 kΩ
      • 10 x Resistor 1 MΩ
    R129.90  Inc VAT
    2-Channel Isolated CAN FD Expansion HAT for Raspberry Pi, Multi Protections (CAN fd hat for pi)

    The 2-CH CAN FD HAT is a 2-Channel CAN bus expansion HAT designed for Raspberry Pi, supports CAN FD (CAN with Flexible Data-Rate). It will enable CAN bus for your Raspberry Pi, not only the original CAN 2.0 protocol, but also the CAN FD extension, with higher data throughput.

    Thanks to multi onboard protection circuits, including 500W lightningsurge, ESD protection, short circuit protection, and electrical isolation, it make the communication more safe and more reliable.

    • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
    • Supports both traditional CAN2.0 and CAN FD protocols
    • Breakout SPI control pins, for connecting with host control boards like STM32/Arduino
    • Onboard electrical isolation, up to 5KV isolated voltage, stable operation, higher anti-interference capability
    • Onboard lightningproof, ESD protection, short circuit protection, more safe communication
    • Onboard voltage translator, select 3.3V/5V operating voltage by jumper
    • Onboard 120Ω terminal resistor, configured by jumper
    • Comes with development resources and manual (examples for Raspberry Pi/Arduino)


    CONTROL BUSSPIPOWER SUPPLYExternal power supply terminal OR Raspberry Pi
    LOGIC LEVEL3.3V/5VDIMENSIONS65.0 × 56.5mm

    What Can It Do?

    Enable Isolated And Stable CAN FD Capability For Your Raspberry Pi

    Designed For Raspberry Pi Series

    Standard Raspberry Pi 40PIN GPIO Header, Customized For Raspberry Pi Series Boards

    2-Channel CAN Support

    MCP2518FD CAN Controller MCP2562FD CAN Transceiver

    Electrical Isolation Circuitry Safe & Stable

    SM24CANB TVS Diode, ESD Protection, Transient Peak Voltage Protection

    Flexible With Handy Jumpers

    Easily Select 3.3V / 5V Operating Voltage, Or Enable/Disable 120Ω Terminal Resistor, Via Onboard Jumpers

    What's On Board

    1. MCP2518FD controller
    2. MCP2562FD transceiver
    3. SI8642ED digital isolator
    4. MP1584EN power chip
    5. RT9193-33 power chip
    6. B0505LS-1W power supply isolation module
    7. Standard Raspberry Pi 40PIN GPIO header
    8. CAN bus screw terminal
    9. External power supply terminal
      8~26V DC input
    10. MCU control pins
      for use with host boards like Arduino
    1. 120Ω terminal resistor switch
    2. 3.3V/5V logic level switch
    3. CAN operating mode selection
      A: CAN_0 and CAN_1 use two separated SPI (default)
      B: CAN_0 and CAN_1 share a single SPI
    4. Power indicator
    5. 2A fast resettable fuse
    6. Power supply reverse-proof diode
    7. Power supply flow backward proof diode
    8. Freewheeling diode
    9. SM24CANB TVS diode

    Pinout Definition

    Outline Dimensions

    Resources & Services

    R1,599.90  Inc VAT
    Dedicated Aluminum Heatsink for Raspberry Pi Zero Series, Zero / Zero 2 W (dedicated heatsink for zero )

    Aluminum Heatsink For Zero Series
    Dedicated Aluminum Heatsink, Corrosion / Oxidation Resisting, Better Heat Dissipation

    Tailored For Raspberry Pi Zero Series
    Matching With The Zero On Size And Mounting Holes, Fast Heat Dissipation

    Used With Zero Boards

    for reference only, Zero is NOT included.

    Outline Dimensions

    * measured manually, for reference only.

    How To Install

    Assembly on Raspberry Pi Zero 2 W

    Assembly on Raspberry Pi Zero


    Weight: 0.028 kg

    What's in the box?

    1. Zero-HEATSINK x1
    2. Thermal tapes 3PCS x1
    3. Mini cross wrench sleeve x1
    4. Screwdriver x1
    5. Screws pack x1
    1  2  3  4  5 
    R56.90  Inc VAT
    SK6812 Self Adhesive 30 LED Bare Strip-1M (RGB strip 1m white)

    This is the famous NeoPixel compatible digitally addressable RGB LED strip based on SK6812 or WS2812B. Yes, and it is, of course, compatible with the NeoPixel library from Adafruit.

    This LED strip comes in 1-meter length with SK6812 Self Adhesive 30 LED Bare Strip-1M.  SK6812 or WS2812B or Neopixel is addressable RGB LED, controllable from many microcontrollers including Arduino (Arduino UNO, Maker UNO, etc), Teensy, Raspberry Pi, ESP8266, ESP32 and many more. And the best of all, the control of all these LEDs uses ONLY ONE digital output pin from the controller.

    These LED strips are fun and glowy. With 30 RGB LEDs per meter, you can set the color of each LED's red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel). The LEDs are controlled by shift-registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 (one) digital output pin is required to send data down. The PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs for you.


    • Maximum 5V @ 60mA draw per LED(all colors on full brightness)
    • 5VDC power requirement (do not exceed 6VDC) - no polarity protection
    • LED wavelengths: 630nm/530nm/475nm
    • Connector: 3-pin JST SM
    • May ship with either WS2812B or SK6812-based LEDs. They are the same brightness, color, and protocol
    • LED package: SMD LED
    • strip specifications: 30 LEDs per meter
    • Color: Full RGB (8-bit brightness control for each color)
    • Length: 1 meter

    What's in the box?

    • 1 x SK6812 Self Adhesive 30 LED Bare Strip-1M


    R154.90  Inc VAT
    Per Page      1061 - 1080 of 1277