Automation

Home Automation
Sort By:  
Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R539.90  Inc VAT
Connect up to 7 Current and 1 voltage sensor to a raspberry pi.
R1,399.90  Inc VAT
R242.16  Inc VAT
R289.90
R269.90  Inc VAT
30A-1V Split-Core SCT013 AC Current Sensor (30A split core current sensor)
Description:

This is split-core current transformer is an AC current sensor. It is used for current measurement, monitor and protection for AC motors, lighting equipment, air compressors, home automation etc.

Features:

- Opening size: 13x13mm
- Rated input current (RMS): 10% - 120% of that is 3A - 36A
- Output voltage(RMS): linear output. When the input current is 30A, the output voltage is 1V
- Linearity: ± 3%
- Output connectors: 3.5mm standard three-pin plug
- Lead length: 1 m

What's in the box?

1 x Current sensor


This sensor is perfect for use with our Raspberry Pi RPICT3T1 current and temperature sensor board.
R159.90  Inc VAT
Soil Moisture Sensor 12V DC Relay Control Module Automatic watering switch (automatic water relay sensor)
Description:

When the soil moisture is lower than preferred setting, the relay will automatically pull in, start the sprinkler, water pump etc. until the moister reaches the desired humidity level and automatically stop.
Product use: Through the potentiometer, adjust to the desired soil moisture level

Specifications:

Electrical parameters: Supply voltage: 12VDC
Input current: more than 100mA Relay Load Max: 10A 250V AC or 10A 30V DC

Module instruction:

1 sensors applied to the detection of soil moisture; Module
2. Blue potentiometer is used to adjust soil moisture level, clockwise adjustment and control the humidity will be bigger, counterclockwise smaller; 3. Due to module delay function, adjust the humidity value, wait about 5-8 seconds, see if the the relay state changed, the green LED lamp will also have corresponding change, until adjusted to meet the requirements.


Package Includes:

1 x Soil moisture control module
1 x Soil sensor
2 x 20cm long DuPont lines
R74.90  Inc VAT
RPICT3T1 100 Amp Raspberrypi 3x Current Sensor Adaptor 1 x temperature (lec 100A 3 current 1 temp board)
RPICT3T1

Please note: Raspberry Pi and sensors are NOT INCLUDED
Raspberrypi AC current hat with temperature

Online Documentation
  • 3x AC Current Ports.
  • 1x Temperature Ports.
  • Provides Irms, EstimatedPower, Temperature.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.
Package Content
  • 1 RPICT3T1 Unit.
  • 2 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.
Recommended SensorsTemperature:Current Sensor:
Technical Specifications

MicrocontrolerAtmel Attiny84
MCU Frequency8Mhz
Operating Voltage3.3V
Waveform Sampling2500sps
Fastest Data Polling600ms
Vertical Resolution10 bits (1024 steps)
CommunicationUART Serial Port
FirmwareArduino (open source)
Dimensions56x35mm
Programming port6 pin ISP
Compatible OSAny supporting GPIO serial port access
Compatible RaspberrypiAll of Family 1,2,3,4 and Model A, B
Compatible CTCurrent output type
AC Current Range100A
Max Temperature probes8
Smallest Readable CurrentApprox 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R539.90  Inc VAT
RPICT7V1 30A Version 5 - 7 CT - 1Voltage - Master (lec 30A 7 current 1 volt board)
RPICT7V1 Version 5Raspberrypi AC current and voltage hat






  • 7x AC Current Ports.
  • 1x AC Voltage Ports.
  • Provides Irms, Vrms, RealP, ApparentP, ReactiveP, PFactor, Frequency, EstimatedP.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.
  • Stackable with RPICT8 Slave.
Package Content
  • 1 RPICT7V1 Unit.
  • 4 Mounting Stand off with screws.
The listing does not include sensors and Raspberry pi.
Recommended SensorsVoltage:Current:

Technical Specifications

MicrocontrolerAtmel Atmega328p
MCU Frequency16Mhz
Operating Voltage5V
Waveform Sampling4400sps
Fastest Data Polling1400ms (all 7 channels)
Vertical Resolution12 bits (4096 steps)
CommunicationUART Serial Port
FirmwareArduino (open source)
Dimensions56x65mm
Programming port6 pin ISP
Compatible OSAny supporting GPIO serial port access
Compatible RaspberrypiAll of Family 1,2,3,4 and Model A, B
Compatible CTCurrent output type
AC Current Range30A
AC Voltage Range240V
Smallest Readable CurrentApprox 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Connect up to 7 Current and 1 voltage sensor to a raspberry pi.
R1,399.90  Inc VAT
220V 360 Degree Recessed Ceiling Occupancy PIR Motion Detector Time Delay Light Switch (220AC pir switch occupancy)
Description:

Are you interested in saving energy? These new Recessed PIR motion/ occupancy sensor is perfect way to start saving energy and also on your bills.

Specifications:
Voltage:AC220-240V/50Hz
Load:800W (incandescent bulbs, halogen bulbs)/200W ( energy saving lamp, fluorescent lamp, LED bulb)
Detection Angle: Ceiling Installation 360°/Wall Mounted 140°
Sensing Distance: Max 8M (24°C)  Adjustable Distance
Delay Time: 5S, 30S, 1Min, 3 Min, 5 Min, 8 Min Time Adjustable
Light Control Settings: 10 ~ 2000Lux Light Control Adjustable

Package Includes:
1 X PIR Ceiling Light Switch
R299.90  Inc VAT
DC 12V PIR IR Sensor Module Relay (12VDC pir relay occupancy)
Description:

Based on infrared technology, automatically control products, when someone enters switch sensing range, pir detect changes in the human body infrared spectrum, switch automatically switches the load, do not leave the sensing range (who are active), the switch will continue to be on.

Person leaves, switch off automatically load delay.

Convenient and  saves energy.

Specifications:

1. Bipolar design: three-wire connection, and the load capacity 100W

2. Automatic sensors: switch immediately turned on with delay off after you leave.

3. Relay switch: can withstand high current output, high power load.

4. Adjustable delay time: 10 seconds -350 seconds

5. Ultra Low Power: Switch own power <0.0088W/h (annual power consumption of <0.077 degrees)

6. Induction: Passive

7. Operating Voltage: DC 12V

7. Inductive mode: passive infrared pyroelectric

6. Quiescent Current: 50uA

7. Sensing Distance: 3 to 5m

8. Load Capacity: Maximum: 100W

9. Induction Angle: About 120°, 100 ° up and down

10. Load Range: Various types of DC LED lamps, load

11. Ambient Temperature: -20 to 50℃

12. Output Mode: Relay control output DC 12V high level / low level

13. Size: 45 x 30mm, PIR lens diameter: 12mm

Wiring instructions:

Red wire: Power input 12V
Black wire: Power output -12V
Yellow wire: OUT 12V power output

Package includes:

1 x DC 12V PIR IR Sensor Module Relay
R119.90  Inc VAT
Hotel Energy Saving Key Card Switch (hotel card switch)
Description

Although the reader does not read the information on the NFC card, it is triggered by a 125 khz NFC card

- Color: White
- Case Material: Fireproof PC Plastic
- Size: Approx. 86mm x 86mm/ 3.39x3.39"
- Voltage: AC 180v-260v
- Maximum load power: 6000w 
- The delay standard: 10-20 seconds
 
Features

● Smart Induction Hotel Power Switch
Convenient and energy saving, low consumption, easy to install and use
● Power function
This power switch can power the room.
● LED Display Design
The LED display is designed to meet the modern hotel trends and is convenient for night operation.
● Delayed Power Outage Design
Remove the door card when leaving, the total power of the room can be automatically disconnected within 15 seconds., which gives enough lighting time for the guests to leave the room.
● Suitable for various places such as Villa, Hotel, Business club etc.

What's in the box?

- 1 x Power Switch (Card Not Included)
R242.16  Inc VAT
R289.90
automation:bit (automation:bit)
Description:

Control and monitor your world with automation:bit! It's tolerant of up to 24V, with analog and digital inputs, outputs, and a relay, so it's ideal for automating low-voltage systems in your home.

Just slot in your micro:bit, then code automation:bit with the block-based Microsoft MakeCode editor. Hook up buttons to the inputs, use the built-in buttons on micro:bit, or the light-sensing capability of the LED matrix to control devices connected to automation:bit. Or why not use a second micro:bit's radio function as a remote control?

WARNING! automation:bit should not be used with voltages greater than 24V and especially not with mains voltages!


Features
  • Comes fully-assembled and ready to use
  • 1 x 24V @ 2A relay (NC and NO terminals)
  • 3 x ADC channels (0-24V range)
  • 3 x 24V tolerant buffered inputs
  • 3 x 24V tolerant sinking outputs
  • 3.5mm screw terminals
  • Compatible with micro:bit
  • Microsoft MakeCode support
  • No soldering required!
Software 

You can code automation:bit with the block-based Microsoft MakeCode editor, that'll get you started with using all of automation:bit's functionality.

To add the automation:bit library in MakeCode, click on the cog at the top right hand corner, then "Add Package", then enter the URL "https://github.com/pimoroni/pxt-automationbit". You can find full instructions at the GitHub repository for the library.


R269.90  Inc VAT
Automatic DC 5V-30V 10A Infrared PIR Motion Sensor Switch For LED Light Strip (black pir switch DC)

Description:

Great for small 12 volt DC solar panel LED Lighting systems to conserve battery power; also well suited for occupancy LED lighting control and security LED Lighting systems

Specifications:

  • Influence control: Light Infrared PIR
  • Two light modes: all day/at night(Auto switching on when detecting people coming.)
  • Super energy saving, super sensitivity within 7 meter distance.
  • Built in light sensor which can identity day and night by itself,
  • Sensor sensitivity distance: ≥7m
  • Sensor sensitivity angle: 145°
  • Load current:10A
  • Working voltage:DC 5V-30V
  • Delay time: If people leave, light will delay 30s-150s(Adjustable) to turn off
  • Certificate: CE
  • Suitable for use in homes, wardrobes, kitchens, stairs, camping tents...
  • Size:50mm x 43mm x 20mm(approx)
  • 5.5 x 2.1mm male to male cable length:1M(approx)
  • 5.5 x 2.1mm male to female cable length:1M(aprpox)
  • Color:Black
Package includes:
  • 1 x PIR sensor
  • 1 x 5.5 x 2.1mm male to male cable
  • 1 x 5.5 x 2.1mm male to female cable
R249.90  Inc VAT
R249.90
RPIZ_CT3T1 3 current and 1 Temperature 30A AC adapter for Raspberry Pi zero (lec zero 3 current 1 temp)

The RPIZ_CT3T1 is the same unit as the RPICT3T1 in the Raspberry pi Zero format.

Refer to the RPICT3T1 for full documentation.

Use with sct-013-000 split core current sensor and DS18B20 temp sensor

Please note: Raspberry Pi Zero and sensors are not included


R649.90  Inc VAT
RPIZ_CT3V1 3 current and 1 Volt 30A AC adapter for Raspberry Pi zero (lec zero 3 current 1 volt)

The RPIZ_CT3T1 is the same unit as the RPICT3V1 in the Raspberry pi Zero format.

Refer to the RPICT3V1 for full documentation.

Use with sct-013-000 split core current sensor and 230VAC to 9VAC power adapter

Please note: Raspberry Pi Zero and sensors are not included



R679.90  Inc VAT
DC 5V WCS1800 Hall Current Detection Sensor Module 35A Precise With Overcurrent Signal LED (WCS1800 Hall Current)
Description:

The WCS1800 Hall Current sensor has two functions

  • current detection
  • over current protection (can be preset from 0.5A to 35.0A)

Features:

Operating voltage: DC 5V
Current detection range: DC +-35A, AC 25A
Linearity: K=60mV/A
Limit current range: 0.5A to 35A(for on/off value output)
Over current signal indicator LED
Sampling current conversion analog voltage signal output and it can connect ADC; TTL level signal output and it can connect MCU IO port control
Board size 37mm x 31mm
Working temperature: 25 to 85C

Interface



VCC: power positive
DOUT: TLL high/low level signal output
GND: power negative
AOUT: sampling current signal conversion voltage output port

Analog voltage signal output (AOUT)

Relationship between detection current and analog signal output is shown below:

Analog signal output: V0=Vcc*0.5±la*K (la is actual current through current detection pin, and K is linearity)

Eg: Input current is 1A, Vcc=5V and WS1800 linearity is 60mV/A
  1. When the current flows in from positive direction: V0=Vcc*0.5+la*K, V0=(2.5+0.06)V=2.56V
  2. When the current flows in from negative direction: V0=Vcc*0.5-la*K, V0=(2.5-0.06)V=2.44V
  3. If it is an AC signal: V0=Vcc*0.5+la*K, V0=(2.5+0.06)V=2.56V

The above are ideal values. There might be some precision errors.

On/Off output(DOUT)

  1. Make sure the current flows in from the positive direction. Adjust to the desired current warning level.
  2. LED will be on when current is below the setting and DOUT will be low.
  3. When the detected current is higher than your setting, the LED will turn off and the DOUT pin will go high.

Package Includes:

1 x WCS1800 Hall current detection sensor
R219.90  Inc VAT
Wemos® Higrow ESP32 WiFi bluetooth Battery DHT11 Soil Temperature And Humidity Sensor Module (Wemos Higrow)
Description:
 
More details available at:https://github.com/LilyGO/higrowopen


A LG 3000mAH 18650 battery could make ESP32 run 17 hours or more.
This capacitive soil moisture sensor differs from most of the resistive sensors on the market, using capacitive sensing principle to detect soil moisture. It avoids the problem that the resistance sensor is easy to corrode and greatly prolongs its working life.
Size: 193.5mm x 29.4mm
 
Package includes:
 
1 x Wemos® Higrow ESP32 WiFi bluetooth Battery DHT11 Soil Temperature And Humidity Sensor Module
R389.90  Inc VAT
SONOFF 4CH PRO R3 AC100-240V 50/60Hz 10A 2200W 4 Gang WiFi DIY Smart Switch APP Remote Control Works with Alexa and Google Home (sonoff 4ch pro R3)
Overview:

SONOFF 4CH R3 & 4CH PRO R3 are both 4-gang DIY Wi-Fi Smart Switches designed to give you the ability to integrate smart control into your existing home to enable a smart home. Each smart switch has 4 gangs that can be used to control lights and other home appliances at the same time in four areas of your home. There is a major difference between 4CH R3 and 4CH PRO R3, which is 4CH PRO R3 is designed with an additional function for RF control. The function is purposely adopted to make you turn on/off the device connected with 4CH PRO R3 via the RM433 remote controller.
Actually, SONOFF has ever released two types of 4-gang smart switch (4CH R2 and 4CH PRO R2.) which comes with almost same functions with 4CH R3 and 4CH PRO R3. But all the above units are still different in 3 working modes including self-locking, interlock and inching mode. The new improvement on 4CH R3 and 4CH PRO R3 compared with 4CH R2 and 4CH PRO R2 is for users to set these 3 working modes on eWeLink APP instead of the hardware itself, easier to operate. So you can enable self-locking mode to turn on/off 4 connected devices separately, interlock mode to turn on 1 connected device every time and turn off the rest of devices simultaneously and inching mode to turn on 1 connected device and then make it turn off automatically after a given time (0.5 - 3600s). For the device away from the switch, you can create a moveable space in virtue of a DIN rail to make them be connected. Simply activate devices through your voice when the switch works with Alexa and Google Home smart assistant.

Features:

- Remotely control connected lights or devices via APP
- 3 working modes with self-locking, interlock and inching mode for even remote control garage door and roller blinds
- Support scheduling a timer to make devices automatically start and stop to work
- Customize smart scenes to make the device connected with the switch to trigger other devices
- Share the control permission of devices to other accounts to control together
- Check real-time ON/OFF status of devices on your mobile phone
- Power on state allows users to set the On/Off/Keep status for the connected device before power failure and ensure it remains the arranged status after power restoration

4CH PRO R3 Specifications:

Voltage Range: 100-240V AC 50/60Hz(DC: 9-23V)
Max. Load: 10A/2200W/Gang 40A/8800W/Total
Wireless Frequency: WiFi 2.4GHz
Wireless Standard: IEEE802.11 b/g/n 2.4GHz2.4GHz(2400M-2483.5M);
Security Mechanism: WPA/WPA2
Enclosure Material: PCV0
Gang: 4
Dimension:145*90*34 (mm)
Operating Temperature(recommended): -10ºC-40ºC(14°F-104°F)
Operating Humidity: 5%-95%RH, Non-condensing
4CH PRO R3 Certification: CE(Download), FCC (Download)

Download Center:

4CH R3 4CH PRO R3 User Manual

4CH R3 4CH PRO R3 Specification
4CH R3 4CH PRO R3 Quick Installation Guide

Package includes:

1 x Sonoff 4CH PRO R3
1 x User Manual
R759.90  Inc VAT
R799.90
SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor Real Time Low-battery notification Works with SONOFF ZigBee Bridge eWeLink APP (zigbee SNZB-02)

Note 1: Batteries not included - ( 3V CR2450)
Note 2: SNZB-02 must be used with the Zigbee Bridge.


Description:

SONOFF SNZB-02 is a ZigBee temperature and humidity sensor that can seamlessly work with SONOFF ZigBee Bridge to track and record the temperature and humidity change in your home, which all real-time readings can be checked on eWeLink APP. Better still, you can set a condition in the smart scene that is the fan is turn on/off when the temperature reaches the limit value, or the dehumidifier in your room starts working once the humidity is over higher, helping prevent the growth of mildew and allergens. You can set a smart scene to trigger alerts through events like high/low temperature, high/low humidity conditions and more.

Device sharing function makes your kids, family, and even the neighbors informed about the environmental conditions of your home with their mobile phones.

It is a battery-operated sensor that can be placed in any corner of your house to monitor the room temperature and humidity. Installation without any tool, simply stick the sensor on the surface of the wall or device and see it nicely to work for you!

1. Do not install on a metal surface, it will affect the wireless communication distance.
2. Installation height of less than 2 m is recommended.
3. The device can be operated intelligently via working with the SONOFF ZigBee Bridge to communicate with other devices.

SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor Overview

Features:
Monitor indoor temperature and humidity.
Sync the real-time temperature and humidity recordings to APP.
Can trigger Wi-Fi devices in smart scene.
Add a camera to ensure you know any emergency in your home.
Low-battery notification.
Quick and easy to install.

Specifications:
Battery: 3V(CR2450)
Wireless protocol: Zigbee (IEEE 802.15.4)
Dimensions: 43mm x 43mm x 14mm

What's in the box
1 x SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor

R239.90  Inc VAT
SONOFF SNZB-01 Mini Zigbee Wireless Switch Two Way Control Light Switch Smart Home Works with eWeLink APP SONOFF Zigbee Bridge (zigbee SNZB-01)

Note 1: Battery not included(3V CR2450)
Note 2: SNZB-01 must be used with Zigbee Bridge.

Description:

SONOFF SNZB-01 Zigbee Wireless Switch is a mini and exquisite ZigBee wireless smart switch replying on SONOFF ZigBee Bridge that allows you to reach the purpose of scene linkages between ZigBee devices (SONOFF BASICZBR3 DIY smart switch and S31 Lite zb smart plug) and Wi-Fi devices. The button switch is customizable with three control options - single, double press and long press, so you can, pretty easily, program routines and actions as simple as you require. One-tap pairing. It’s so much easier to pair it with multiple connected devices that you want to manage, just tap on the APP to get all devices paired. The brilliance of the button lines in its flexible movability, you can strategically place it or move it around your house to where it will be most helpful, then create a smart scene to make it work for you based on different button actions that you customized. Two-way control is even available for you to turn on/off the light from two locations. The button is battery-operated that your mobile phone will receive a low-battery notification when the remaining battery level is less than 10%, maybe it’s time to change the battery. Note: 1. Do not install on the metal surface, otherwise it will affect the wireless communication distance. 2. The installation height of less than 2 m is recommended. 3.The device can be operated intelligently via working with the SONOFF ZigBee Bridge to communitcate with other devices.
R209.90  Inc VAT
SONOFF SNZB-03 ZigBee Motion Detect Sensor Alarm Alert Notification Works with SONOFF ZigBee Bridge eWeLink APP (zigbee PIR)

Note 1: Battery not included (3V CR2450)
Note 2: SNZB-03 must be used with Zigbee Bridge.


Description:

If your concern is not only about home security but about using motion to turn on or off the lights, well, SONOFF SNZB-03 might be the answer for you.

This ZigBee motion sensor is an extra-handy smart device for placing anywhere in your home to detect motion and trigger alarms. That means the sensor will send an instant alert notification to your mobile phone whenever the motion is detected if this security system is armed. If you have a SONOFF ZigBee Bridge, you can connect the sensor to it to activate Wi-Fi devices, not merely ZigBee devices. For example, you can set a scene for your living-room light so that it will automatically turn on when you walk through the living-room.

Boasts 110°view field and 6m detection rang and you can early receive an alert message of someone’s presence, accordingly taking measures to reduce the possibility that your house is threatened. Share control is available for multiple users to check and monitor your home together. Easy and tool-free installation, 3M adhesive installation significantly saves your time. Powered by a battery which makes it convenient to stick it on any place that you want to monitor.

You will get a notification of low-battery level when the battery life reaches 10% remaining.

Features:
Create smart scenes to activate Wi-Fi smart devices.
Detect movement and trigger alert messages.
Turn on/off the devices through your movement.
Work with the SONOFF camera to monitor your home.
6m detection distance and 110°viewing angle.
Share the sensor to your family to together keep eyes on your home.
3-month history records check.
Low-battery notification.
Quick peel and stick installation

Specifications:
Battery: 3V(CR2450)
Wireless protocol: Zigbee (IEEE 802.15.4)
Material: PC
Dimensions: 35mm x 39mm x28mm

R269.90  Inc VAT
SONOFF SNZB-04 ZigBee Wireless Door/Window Sensor Notification via eWeLink APP Smart Home Security (zigbee SNZB-04)

Note 1: Battery not included (3V CR2450)
Note 2: SNZB-04 must be used with Zigbee Bridge.

Description:

The wireless door/window sensor is essential for knowing who is coming in and out of your home, so it is most often used as part of smart security system.

SONOFF SNZB-04 is a ZigBee two-in-one wireless door/window sensor that can be put on your door or window to tell you with an alert notification if your door or window is opened or closed, adding an extra layer of security to your home. The sensor provides you the possibility to create a scene linkage of ZigBee and Wi-Fi devices. Both the opening and closing status of the door/window are synced on your mobile phone, no longer to think back whether the door/down is off or not. It is really useful and can help you turn on or off the light in the action. Works with SONOFF ZigBee Bridge in harmony, you can set a scene to get your hallway lighted immediately when the door is opened.

Its application can also extend to wide areas like drawers, garage doors, blinds, etc. Just stick it anywhere two things connect and it is always safe even if you don’t keep watch on it. Share the sensor with your family to give them an ability to quickly control and monitor your home together. Simple installation for easier setup. Peel and directly stick it on the targeted place or object, a smart security system is ready for you.

Features:
Remind you when the door/window is open and closed.
Sync the opening & closing status of door/window on APP.
Can make ZigBee and Wi-Fi devices keep linkage.
Control the light with an action.
Support adding the SONOFF camera to view what happened at your home.
Share control makes other users control the connected device quickly.
3-month history records check .
Low-battery notification.
Simple peel and stick installation.

Specifications:
Battery: 3V(CR2450)
Wireless connection: Zigbee 3.0

Dimensions:
Magnet: 32mm x 15.6mm x 13mm
Sensor: 47mm x 27mm x 13.5mm

R244.90  Inc VAT
SONOFF Dongle Zigbee CC2531 USB Dongle Module Bare Board Packet Protocol Analyzer Interface Dongle Capture Packet Module (zigbee dongle)
Description:

The CC2531 USB dongle is a fully operational USB device which provides a PC interface to IEEE802.15.4 / ZigBee applications, comes with a CC2531ZNP-Prod firmware, the dongle can be plugged directly into your PC/Raspberry etc used as a Zigbee packet sniffer.



Features:

Flashed with CC2531ZNP-Prod firmware for zigbee2mqtt application Lead out 8 IO connectors Debug interface Size: 5.6*1.6*0.7cm Two buttons and two LEDs for user interaction
R154.90  Inc VAT
SONOFF Zigbee 3.0 ZB MINI Smart Switch Two Way APP Remote Control Switch Smart Home Works with SmartThings (zigbee ZBMINI)
Description:

SONOFF ZBMINI is a ZigBee-enabled two-way smart switch that is compatible with different hubs, including SONOFF ZBBridge, Amazon Hub, Samsung SmartThings Hub and Philips Hue Hub. The ZigBee3.0 protocol gets ZBMINI and ZigBee bridge to be paired in a quick way. ZBMINI is safer to use in you home that is promised by the fire-proof and flame-retardant shell. Additionally, AES-128 encryption ensures the safety is extended to data device privacy, no worry about privacy disclosure of your device. It can be as a Zigbee router to help transmit the ZigBee signal to ensure a stable connection when multiple Zigbee devices are used for your home. If you are keen on two-way control, you can connect a Single Pole Double Throw switch as the external connection to expand the control way.



R239.90  Inc VAT
Per Page      21 - 40 of 50