Generic1

• Shrinkage Ratio: 2:1 (will maximum shrink to 1/2 its supplied diameter)
• Cutting method: Scissors or sharp knife

These electrical connectors are designed for ribbon cables and telecommunications applications. They are also referred to as insulation-piercing contacts (IPCs).

Specifications

• 40 Pins Male Standard 0.1" 2.54mm Row spacing
• Low Profile with mounting ears
• 0.1" Pin spacing 0.1" Row spacing, Mates with IDC & PCB male Receptacles
• Insulation Displacement Connector terminates to 0.050" (1.27mm) flat ribbon cable

What's in the box?

1 x 40-PIN IDC SOCKET CABLE MOUNT

• Primary input voltage: 19V
• Input Voltage Min: 14V
• Maximum input voltage: 35V
• Fixed output voltage: 12V
• Pressure drop: 2V
• Output channel number: 1
• Number of pins: 3
• Output current: 1.5A
• Package Type: TO-220 Tube
• Operating temperature range: 0℃ to 150℃ 
• SVHC (Highly Concerned Substances): No SVHC (20-Jun-2011)
• Device number: 7812
• Tolerance, operating voltage : 4%
• Voltage Rectifier Type: Positive Fixed
• Maximum supply voltage: 27V
• Power supply voltage minimum: 14.5V
• Surface Mount Devices: Through Hole Installation

• Size: (Approx.)12x12x7.3mm
• Life: 100000 times
• Quantity: 10pcs
• Current: 50mA
• Voltage: 12V

• Python library
• Introduction to Buttons and Switches
• Types of buttons and switches

IR (Infrared) sensor tuned to 38KHz, perfect for receiving commands  from a TV remote control. Runs at 3V to 5V so it's great for use on the  Raspberry Pi!

To use, connect pin 3 (all the way to the right) to  5V power, pin 2 (middle) to ground and listen on pin 1. It doesn't do  any decoding of the signal, just passes the 'raw data' along.

Specifications

• Carrier Frequency: 38kHz
• Transmission Range: 45m
• Directivity: 45°
• Supply Voltage Min: 2.5V
• Supply Voltage Max: 5.5V
• Supply Current: 350µA
• Opto Case Style: Through Hole
• Operating Temperature Min: -25°C
• Operating Temperature Max: 85°C
• Packaging: Each
• Operating Temperature Range: -25°C to 85°C
• SVHC: No SVHC (16-Dec-2013)
• Supply Voltage Range: 2.5V to 5.5V
• Manufacturer: VISHAY MINICAST AGC2

What's in the box?

1x Infrared Receiver

Resources

• Using an IR remote with a Raspberry Pi
• Datasheet

• Has the ability to control eight separate appliances or pieces of equipment
• Eight on-board optoisolators enable direct interfacing to microcontrollers
• Eight red LED status lights on-board show relay activity
• Widely used in PLC control or smart home control
• 4 x M3 mounting holes for easy fixing via standoffs

• 15-20mA drive current needed per channel
• Relay coil maximum operating voltage: 5V
• Relay coil maximum current: 89.3mA
• Relay contact maximum: AC250V at 10A or DC30V at 10A
• No. of relays/channels: 8
• Item size: 134 x 55 x 20mm
• Item weight: 116g

• 1 x 8 Channel Relay Module

• Interfacing with a relay

Warning
Exercise proper caution when connecting mains driven equipment or appliances to relay module as lethal current will be present.

This flexible 4x4 matrix keypad is connected to an 8 pin DuPont Female connector. It can be attached to a surface via the adhesive back by removing the white protective paper backing.

• Contact Resistance: 10Ω-500Ω
• Insulation Resistance: 100MΩ 100V
• Key Operating Force: 150-200N
• Circuit Rating: 35V DC, 100mA, 1W
• Dielectric Strength: 250V RMS (50-60HZ/Min)
• Electric Shock Jitter: ï¼ÂÂœ5ms
• Operating Temperature: -40 deg. C ~ 80 deg. C
• Storage Temperature: -40 deg. C ~ 80 deg. C
• Vibration: 20G, max
• Size: 68mm x 76mm

• Matrix Keypad

• Each Relay has LED indication when ON
• SPDT Relays with terminal block outputs.
• Relay Coil voltage: 5 VDC
• Power Requirement: 5 VDC
• 10A 250V AC / 10A 30V DC

• Display Colour: Red
• The black line connects to the negative electrode, red line connects to positive pole of power supply, white line connects to positive pole of tested power supply
• Material: Plastic Shell
• Display Digit: 3
• Measuring Range: DC 4.5-30V
  Working voltage: 4.5-30V
• Overall Dimension: Approx 28mm x 47mm x 21mm

• Python library
• Introduction

Tactile Switches or tact switches are an on/off electronic switch that is only on when there is some pressure put on it or when the button is pressed. As soon as the tactile switch button is released and the pressure has been took off, the circuit is then broken.

• Size: (Approx.)6x6x5mm
• Life: 100000 times
• Quantity: 5pcs
• Current: 50mA
• Voltage: 12V

Please note: Pic is for illustration purposes only

The 1N4007 is used as a general-purpose diode. It is normally constructed to be used as a rectifier in the power supply section of electronic devices to convert AC voltage to DC voltage with other filter capacitors.

Specifications

• 1N4007 Diode
• rectifying
• standard 1A 1000V
• DO-41

What's in the box?

5 x diodes

 
Resources

Intoduction
Basics, Types, Characteristics, Applications & Packages

 LM393 comparing two photosensitive resistance, when the imbalance (eg side pressure runway black) immediately control side of the motor stops rotating, the other side of the motor rotation acceleration, so that the car modification direction, return to the right direction, the whole process is a closed loop therefore rapid and sensitive control.

With the aim of simplifying the complex principle, we first have a by digital circuit to the intelligent tracking car, in the assembly process, we could not only familiar with the mechanical principle gradually can learn to: photocell, a voltage comparator, a motor drive circuit, and other related electronic knowledge.

Photosensitive resistance device:

This is light-sensitive resistance, it can detect the external light intensity, the stronger the outside light photosensitive resistance resistance is small, the outside light weaker resistance is greater when the red LED light projected on a white and black runway because reflection rate is different, the resistance value of the light-sensitive resistance will occur obvious difference for subsequent circuit control.

LM393 comparator integrated circuit:

LM393 is a dual voltage comparator integrated circuit, which consists of two independent precision voltage comparator. its role compare the two input voltage, based on the level of two input voltage change the level of output voltage. The output has two states: close to open or close to the low level, LM393 using open collector output, so it is necessary to add the pull resistance to output high level.

DC motor with gear reduction:

DC motor drive the car needs to slow down, otherwise to speed up the car, then ran too fast not control, and the deceleration torque is too small and could not run up. We specialize in custom of this type of motor is integrated with the reduction gear and greatly reducing the manufacture difficulty is very suitable for our use.

LM393 comparing two photosensitive resistance, when the imbalance (eg side pressure runway black) immediately control side of the motor stops rotating, the other side of the motor rotation acceleration, so that the car modification direction, return to the right direction, the whole process is a closed loop therefore rapid and sensitive control.

What's in the box?

1 x Electronic DIY Kit (batteries are not included)

Resources

Assembly steps:

The first step: circuit part of the basic welding
The welding circuit part is relatively simple, the welding sequence according to the element height from low to high, the first 8 resistance welding, welding must use a multimeter to confirm whether the proper welding resistance, polar components such as transistors, green lights, definitely clear electrolytic capacitor polarity as reference element we are photo welding, welding capacitor short is the negative side of the insertion pin PCB screen printing shadow, green welding LED note long pin is positive, and the welding is not too long or easy bad welding, D4 D5 R13 R14 can temporarily do not weld, the integrated circuit chip can be inserted, preliminary after completion of welding check carefully prevent, be negligent.

Second step: mechanical assembly

The universal wheel screw is inserted into the PCB hole, and screwed into the universal wheel nut and a universal wheel. the battery box is stuck on the PCB by the double adhesive tape, the lead wire passes the PCB reserved Kong Han received PCB, the red line is connected with the 3 V positive power supply, and the yellow line is connected to the ground.

Mechanical part and assembly can be mounted first wheels, wheel consists of three pieces of black acrylic round tablets, assembly prior to exposing protective film, the inside of the wheel center hole grows circular hole, middle of the round plate diameter is relatively small, lateral wheel piece center hole Shiyuan, with two screw nuts fixed set good three round tablets, and black self-tapping screws fixed on the rotating shaft of the engine. Finally the silicone rubber tire sleeve on the wheel. Lead connection lead wire of the motor and the wheel assembly is the use of the glue on the PCB making position, attention wheels and the PCB edge retaining sufficient clearance, the motor leads are soldered to the PCB. Note that adequately longer lead, to avoid the motor rotation direction error is convenient for changing the lead wire of the order.

The third step: the installation of opto-electronic circuits

Photosensitive resistance and light-emitting diode (attention polarity) is the reverse installed on the PCB, and the ground distance of about 5mm, the distance between the light-sensitive resistance and light-emitting diode is also about 5mm. Finally can pass electrical test.

The fourth step: Vehicle debugging

In the battery box in 2 AA batteries, switches to dial in the "on", the car driving right reverse is traveling along the direction of the universal wheel, if hold the left side of the photosensitive resistance, the car to the right of the wheel rotation, Keep to the right of photosensitive resistance, the left side of the car wheel must turn, if car travel back can exchange connection of two motors at the same time. as one of the normal back on the other side as long as the exchange of the rear of the motor can be wiring. 

Note: We don't supply any manuals, please note this before you buy this DIY kit.

LM393 Sound Detection Sensor Module for controller detects whether the sound has exceeded a threshold value. The sound is detected via a microphone and fed into an LM393 op-amp. The sound level setpoint is set via an onboard potentiometer.
Can be used for Acoustic control light; give sound and light alarm working with Photosensitive sensor

Note: The Maximum induction distance is 0.5M

• Main Chip: LM393, Electret condenser microphone
• Working Voltage: DC 4-6V
• Signal output indication
• Single channel signal output
• The output effective signal is low level
• When there is sound,output low level and the signal lights

• Direct Replacement for the Raspberry Pi Camera Board Cable
• 300mm Overall Length
• 1mm Pitch
• 15 Way Flat Cable
• Conductor: Tin plated copper
• Insulation: White PVC
• Supporting tape: Blue polyester
• UL rating: UL2896
• Temperature rating: 80°C
• Voltage: 30V
• Flame test: VW-1, FT1, FT2
• CSA Standard: CAN/CSA-22.2 No.210.2

What's in the box?

1 x Camera Board Replacement Cable

• Integrated circuit
• Voltage regulator
• 5V
• Non insulated