Generic1
Specifications
- Size: 62mm(L)x44mm(W)x23mm(H)
- Input Voltage (Trigger): DC 3-32V
- Output Voltage(Line): AC 24-380V
- Output Current(Line): 60 A
- On Voltage: ≤1.6V
- OnOff Time: ≤10ms
- Control Current: 3-35mA
- Transparent Lid Included: Yes
What's in the box?
1 X 60A SSR-50DA Solid State Relay With Cover
Resources
Datasheet available at https://cdn.sparkfun.com/datasheets/Components/General/SSR40DA.pdf
Depending on how hard your relay works, you might want to add a heat sink to it.
Q:During continuity testing with my multimeter why does my relay on the AC side not switch on?
A: The below info was found at http://www.crydom.com/en/tech/newsletters/solid statements - bench test an ssr.pdf
A multimeter determines impedance by injecting a small amount of voltage through it's probes into the circuit being tested. It then measures the current flowing through the probes and calculates resistance. Easy enough; Resistance = Voltage / Current! However, as we just discussed above, a solid state relay’s output turns on by “stealing” a bit of voltage from the AC mains in order to supply current to the gate of the SCRs. Simply put, if the AC mains is not connected to the relay then the output cannot turn on. Since the voltage and current produced by a multimeter is not sufficient enough to turn on the SCRs, the output of a solid state relay will remain in the off state; even with the input signal applied. As a result, SSRs will sometimes fail an incoming inspection because the engineer expects to see a significant change in the output impedance when they turn on the relay.The most effective way to bench test a solid state relay is to construct a simple test circuit consisting of a DC power supply or battery (a 9Vdc battery will work fine in most cases ) and a 60W or 100W light bulb.
Product Features
1) Compliant with CCID
2) Compliant with PC/SC
3) Support IC/ID dual frequency replication
4) Driver-free, no need to download software installation
5) When connect the RFID Reader to the computer with the USB cable, then can find the software.
6) Support ID125K, 8800, 5200, 4305, 5577, 8265 card.
7) Support UID FUID CUID UFUID IC semi-encrypted card, IC full encryption card.
8) Has USB full speed interface
9) Two-color LED light prompt (red light is standby, green is working)
10) Built-in buzzer "beep" sound reminder
How to use the card reader?
Hot Question:
1) Where can i download the software?
Answer: You can download the software via this link:http://www.nsccn.com/download/soft/nfc/nfcPro_wbw.exe
2) Which chip inside in the 5pcs blue keyfobs and 5pcs white cards?
Answer: If you buy the RFID copier + 5pcs UID keyfobs + 5pcs T5577 cards. The 5pcs UID keyfobs is working with 13.56MHz frequency, used to copy the MF 1k card. The 5pcs T5577 cards is working with 125KHz frequency, used to copy the EM4100, TK4100 cards. They are different type card.
3) Why the 5pcs cards in the package read failure?
Answer: Please don't worry, these 5pcs white cards is T5577 (EM4305) type, they haven no data before write. They will can be read successfully after finished written from your TK4100 or EM4100 type card. Thank you.
What's in the box?
1 x RFID Copier Duplicator 125KHz Key fob NFC Smart Card Reader Writer 13.56MHz Encrypted Programmer USB UID T5577 EM4305 Cards Tags
Product size: 35.5 * 17 * 8.3 mm
Input voltage range: 6 to 26 v
Output voltage: 5.2 V (consider charging line loss, output is about 5.2 V, the load end is around 5 V)
Limit the output current: 3 a (in the absence of radiator, stable output current limit is 2 a)
Note 1: is the cathode can't meet the, and the input voltage can't more than 26 v, otherwise it will result in the chip damage!
Note 2: in current work, not touch on the circuit board sampling resistor, IC, or may result in output voltage mutation damage equipment!
What's in the box?
1 x 9V 12V 24V to 5V 3A USB step-down voltage regulator module DC-DC Converter
What's in the box?
1 x DC-DC Vehicle Charging Board 8V-35V to 5V 8A Power Supply Depressurization Module 4 port USB Output mobile Charger
The RF Remote is a 433MHz Wireless 4 Buttons Push Cover Remote. This Wireless 4 Buttons 433Mhz remote control can remotely control any Sonoff RF products. It’s suitable for long distance and multiple switch control. The remote controller is compatible with 433MHz products like the light switches, RF Bridge, Basic RF and 4Ch Pro RF R2.
Note: This RF Remote contains a battery (A27)
This product can work with our smart home products: Sonoff RF, Sonoff 4CH Pro, Sonoff RF Bridge 433, Sonoff TX2 and TX 3 light Switches.
What's in the box?
1 x 433Mhz Wireless Remote
Resources
These are suitable for DIY projects and the Raspberry Pi pcb as the screw outside diameter is only 2.5mm that fits in the Pi mounting holes.
Brass standoffs are essential components in electronic projects, particularly in applications where circuit boards need to be securely mounted within an enclosure or chassis.
Here's how they are typically used:
Board Mounting: Brass standoffs are used to elevate and secure printed circuit boards (PCBs) within an electronic enclosure or chassis. They provide a stable platform for the PCB, preventing it from coming into contact with conductive surfaces that could cause short circuits.
Mechanical Support: Standoffs act as spacers between the PCB and the mounting surface, ensuring proper ventilation and preventing heat buildup. This is crucial for maintaining the integrity of sensitive electronic components.
Isolation: Brass standoffs help to electrically isolate the PCB from the chassis or enclosure. This isolation is essential for preventing electrical interference, reducing the risk of noise and signal degradation, and enhancing overall circuit performance.
Easy Access: Standoffs facilitate easy access to the PCB for maintenance, repairs, or upgrades. By raising the board above the mounting surface, technicians can easily reach components and make necessary adjustments without disassembling the entire system.
Vibration Dampening: In applications where vibration is a concern, brass standoffs can help dampen vibrations transmitted to the PCB, thereby reducing the risk of component failure or solder joint fatigue over time.
Grounding: Depending on the design, brass standoffs can also be used as grounding points for the PCB. By connecting the standoffs to the ground plane on the PCB, they provide a convenient and reliable grounding solution.
Overall, brass standoffs play a crucial role in ensuring the structural integrity, electrical isolation, and proper functioning of electronic systems. Their versatility and reliability make them indispensable components in a wide range of electronic projects.
What's in the box?
1 x Male Female Standoff M2.5 x 7mm
Tired of useful gadgets? Meet the Useless Box! Flip the switch, and a tiny mechanism pops out to flip it right back off. It's perfectly pointless, delightfully disruptive, and guaranteed to spark a smile (or a chuckle of confusion). The ideal desk toy for those who appreciate the absurd.
What's in the box?
1 x Mini useless box Black
Tired of useful gadgets? Meet the Useless Box! Flip the switch, and a tiny mechanism pops out to flip it right back off. It's perfectly pointless, delightfully disruptive, and guaranteed to spark a smile (or a chuckle of confusion). The ideal desk toy for those who appreciate the absurd.
What's in the box?
1 x Mini useless box Black
Arduino is an open-source electronics platform based on easy-to-use hardware and software. Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter message - and turn it into an output - activating a motor, turning on an LED, publishing something online.
Specifications
- Arduino compatible board
- Microcontroller ATmega328
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 6
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
- SRAM 2 KB (ATmega328)
- EEPROM 1 KB (ATmega328)
- Clock Speed 16 MHz
- Length 68.6 mm
- Width 53.4 mm
What's in the box?
1 x UNO R3
1 x USB cable
Resources
Find more info on Arduino at https://www.arduino.cc/en/Guide
UNO R3 is a microcontroller board based on the ATmega328P.
The Arduino Uno R3 comes in two models; the normal version and the SMD version. In the SMD version you have the Atmega328 controller IC as an SMD chip soldered into the board, whereas in the normal version the IC is held on the Arduino by an IC Holder.
Features
- 14 digital input/output pins (of which 6 can be used as PWM outputs)
- 6 analog inputs
- a 16 MHz quartz crystal
- a USB connection
- a power jack
- an ICSP header
- a reset button.
It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
What's in the box?
1 x Arduino Uno SMD
1 x Headers
1 x USB cable (Cable colour might differ prom product pic)
Resources
Getting started with Arduino products
Specifications
- Colour: Black
- Buzzer Type: Piezoelectric
- Sound Pressure Level 85 dB
- Rate Voltage: 12V DC
- Operating Voltage: 3 - 24V
- Max Current Rating 11mA
- Frequency 3900±500Hz
- Drive Method: Drive Circuit Built in
- Mounting Holes
What's in the box?
1 x Piezoelectric Buzzer
Resources
- Python library
- Using a Buzzer With a Raspberry Pi
This is a Mini Real-Time Clock module, it's design for the Raspberry Pi, but it can also be used with an Arduino.
Simply plug this tiny module into the GPIO header on the Raspberry Pi and away you go!
Specifications
- DS3231 RTC IC
- Self-adjust 3.3V and 5V
- Size: 14mm x 14mm x 12 mm
Features
- Smaller
- Work in 3.3V and 5V
- Supported Raspberry Pi and Arduino
What's in the box?
1 x RTC Module
1 x Battery
Resources
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 300mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
What's in the box?
1 x Camera Board Replacement Cable
Standard Single Head Power Cable-1.8m-Standard computer power cable with 3-prong plug on one end and kettle plug connection on the other., OEM, No Warranty
Standard 3 prong South African Plug 16Amp fuse plug on one end and the IEC (kettle plug) connection on the other. Plugs directly into computers, certain monitors and various power supply units. Also known as Power Cord (Kettle Cord) 3 Pin South African, One IEC Connector, 1.8 Meters
• Connects a PC to a 220 volt AC power outlet
• Single CIEC standard compliant moulded PC power plug
• Can be used on standard domestic 3 pin AC power outlets
• 220 Watt rating for SLI and multi-rail power supply use
• 1.8metre Long
What's in the box?
1 x power cord with plug
Specifications
- Power: 1W
- Voltage: 5V
- Material:Monocrystalline Silicon
- Size: 60x110mm
What's in the box?
1x 5V Solar panel
We have used the HC-SR04 Ultrasonic Distance Sensor many times and for many good reasons. It is pretty easy to use, it performs well, and it is very inexpensive. For collision avoidance robots or intruder detection, this sensor is usually all you’ll need.
However, using the HC-SR04 outside is a different story. It is a pretty fragile device and can easily be damaged by dirt, or even high winds. And, above all, it is not waterproof.
For these circumstances you can use this sensor, in more weathered states, even outdoors.
Specifications
- Operating voltage: DC 5V
- Total current work: 40mA
- Acoustic emission frequency: 40khz
- Maximum distance: 2m
- Blind: 25cm
- Resolution: about 0.5cm
- Angle: 70 degrees
- Working temperature: -10 ~ 70 ℃
- Storage temperature: -20 ~ 80 ℃
Wiring
5V (positive power supply)
Trig (control side) RX
Echo (the receiver) TX
GND (negative)
Product Features
- small size, easy to use;
- low voltage, low power consumption;
- high accuracy;
- strong anti-jamming;
- integrated with wire enclosed waterproof probe, suitable for wet, harsh measuring conditions.
Application
1 Horizontal distance;
2 obstacle avoidance, automatic control;
3 traffic control;
4 security, industrial control;
5 artificial intelligence, and research
What's in the box?
1 x DC 5V Waterproof Ultrasonic Module Distance Measuring Transducer Sensor
Resources
Sensor Usage
Basic working principle
(1) using IO port TRIG trigger location, to the high level signal of at least 10us;
(2) module automatically sends 8 40KHz pulse, automatic detecting whether a signal returns;
(3) on signal return, a high level is output through the IO port ECHO, the time duration of the high level is ultrasonic from launch to return. The test distance = (high level time * speed of sound (340M/S)) /2;
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 1000mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
Features
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 1000mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
If your project is particularly resource-hungry then the Raspberry Pi may run a little hot. Cool it down with this nifty little heatsink!
Simply remove the backing from the pre-applied thermal tape and stick it on top of the main processor chip.
Specifications
- 14mm x 14mm (in 7mm height)
- Ideal for use with Raspberry Pi 3/4/zero
- Matte black finish
- Made from anodised aluminium
- Comes with pre-applied thermal tape for easy installation
- Anodised non-conductive coating
What's in the box?
1 x CPU Heatsink 7mm
Note: At 7mm tall this heatsink may interfere with some HAT boards.
Specifications
- Model: F695ZZ
- Material: Chrome Steel
- Size: 5mm x 13mm x 4mm
- Easy to install and replace.
- Less friction and higher speed.
- Smooth operation, high accuracy.
- Durable.
1 x Ball Bearing
Features
- Rating: 3A 250V
- Mounting hole: 20mm
- Poles: SPST
- Terminal: 2-Pin(ON-OFF)
- Contact resistance: ≤30mΩ
- Insulation resistance: ≥100MΩ at 500V DC
- Dielectric strength: 1500V AC for 1 minute
- Operating temperature: -25°C - 85°C
- Electrical life: 10000 cycles
- Colour: black / red
What's in the box?
1 x Mini round red rocker switch
Resources
Introduction to Buttons and Switches
Types of buttons and switches