Generic1

Solder cleaning wire, which is an upgrade from typical sponge or water cleaning techniques. These Cleaning Wire Balls are hard enough to remove debris and some corrosion from the solder tips while being soft enough not to damage the tip. They help to remove oxides and excess solder to preserve tip life and enable clean, precise soldering.

Features

• Made of high quality material, reliable in performance
• Easy to clean soldering head without water
• Remove residues quickly and effectively
• It does not damage soldering head
• Durable for long use
• Avoid soldering tin from splashing everywhere

Specifications

• Material : Steel
• Smokeless : Yes
• Non-toxic : Yes

What's in the box?

1 x Soldering Iron Tip Cleaner Ball

Product updates

• As from 15/05/2025 this product will include 5 Cleaner Balls
  
  

Resources

Introduction to soldering
Video: How to solder properly
The secrets to good soldering

• 5.5mm x 2.1mm barrel
• 26cm cable

• 10A 250VAC
• 10A 125VAC
• 10A 30VDC
• 10A 28VDC

To check compatibility of a new remote with the receiver. Simply press the button on the remote, if the receiver flashes, but does not Triger the relay. The remote will be compatible, and you can start the programing process

To add a remote, press the button on receiver momentarily. The red light will come on. Then press the button on the remote that you want to program in. The red light will start flashing. After 4 flashes in will stop, and the button will be programmed in.

For the setting to take effect, the board needs to be disconnected from it’s power supply. The bellow settings will be done to the 3 headers and bridge pin on the receiver board, above the push button.

• With the header removed, the On button will switch the relay on, and the off button will in turn switch the relay off.
• With the header on Pin 1-2. Both Buttons will become momentary. And only hold the relay in place as long as they are pressed in.
• With the header on Pin 2-3. Each button will be able to switch the relay on and off individually. You will however not be able to switch the button off with the “off” button, if you switched it on with the “on” button. And vise versa.

What's in the box?

1 x Learning Code Receiver Relay
1 x Remote Control

This listing includes: 10 pairs of MC4 parallel connectors for 3 solar panels. (FFFM and MMMF)

Used for connecting solar panels in series or parallel, quick and reliable connection of the solar cables to the photovoltaic system. 

Application

It can be used for connecting 3 solar panels in parallel.

Advantage

1). Easy to use

2). TUV certification

Specifications

• Rated Voltage: (VDC)1000
• Rated Current: (A)40A
• Low Ambient Temperature: (°C)-40°C
• Upper Ambient Temperature: (°C) 90°C
• Degree of Protection (IP Code): IP67
• Contact Material: Copper
• Insulation Material: PPO PA
• Certification: TUV
• Connection resistance: <= 1m Ω
• Insertion force: <=60N
• Withdraw force: >=60N
• Flame class: UL94-VO

1.  Small size, low cost
2.  Easy to integrate
3.  Factory calibrated in wide temperature range: -40…85C for sensor temperature and -40…115C for object temperature
4.  High accuracy of 0.5C over wide temperature range (0... 50C for both TA and TO )
5.  High (medical) accuracy calibration
6.  Measurement resolution of 0.02C
7.  SMBus compatible digital interface
8.  Power saving mode
9.  Customizable PWM output for continuous reading
10.  Embedded emissivity compensation
11.  3V supply voltage

• Comparative output, clean signal, good waveform, strong driving ability, more than 15mA.
• Working voltage: 3.3V to 5V
• Output form: digital switch output (0 and 1)
• Equipped with fixed screw hole, easy to install
• PCB board size: 32mm x 14mm
• Uses the LM393 wide voltage comparator

TB6600 is an easy-to-use professional stepper motor driver, which could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers that can output a 5V digital pulse signal. TB6600 arduino stepper motor driver has a wide range power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for the most of stepper motors.

The stepper driver supports speed and direction control. You can set its micro step and output current with 6 DIP switch. There are 7 kinds of micro steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing its anti-high-frequency interference ability.

As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.

Features

• 9V-40V DC power supply
  
• H-bridge bipolar constant phase flow driver
  
• The maximum output current is 4.0A (eight optional)
  
• Up to 32 segments of six kinds of sub-modes available
  
• Input signal high-speed photoelectric isolation
  
• Standard common anode single pulse interface
  
• Offline keep function
  
• Semi-enclosed chassis can adapt to a more demanding environment
  
• Provide energy saving semi-automatic current lock function
  
• Built-in thermal protection and over-current protection
  

Specifications

• Voltage: up to 50V
  
• ON resistance (upper lower) = 0.4 Ω
  
• Forward and reverse rotation control
  
• 5 kinds of sub-modes selectable (1/1, 1/2, 1/4, 1/8, 1/16 step)
  
• Output current: IOUT = 5.0A (peak within 100ms)
  
• Rated output: IOUT = 4.5 A
  
• Input pull-down resistor: 100 KΩ
  
• Current output alarm pin: Ialert = 1mA
  
• Monitor output pin (MO): Imo = 1mA
  
• With reset and enable pins
  
• With a standby function.
  
• Breaking the traditional single-supply
  
• Built-in thermal protection (TSD) circuit
  
• Built-in voltage protection (UVLO) circuit
  
• Built-in over current detection (ISD), the circuit

Note:

This driver is the upgraded version TB6600, heightening segment to 32 subdivision, suitable for high segmentation applications.
For step motor: 42, 57, 86 type 2 phase 4 phase (4 / 6 / 8 line)

What's in the box?

1 x TB6600 Stepper Motor Driver Controller

Resources

https://danielwilczak101.medium.com/control-a-stepper-motor-using-python-and-a-raspberry-pi-11f67d5a8d6d

https://www.instructables.com/Raspberry-Pi-Python-and-a-TB6600-Stepper-Motor-Dri/

The TB6560 stepper motor control circuit is the most commonly used current circuit, which can control a 2 phase motor (10 – 35VDC) with a maximum output of 3A.

Specifications

• Size: 75mm x 50mm x 35mm  (L x W x H)
  
• Rated maximum output: ± 3A, peak 3.5A
  
• Working voltage: DC 10V-35V
  
• Recommended to use a switching power supply: DC24V power supply
  
• Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16
• Subdivisions.

Features

• Using the Toshiba TB6560AHQ new original chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance.
  
• For two-phase within 42, 57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor.
  
• Automatic half current function.
  
• 6N137 high-speed optical coupling, guarantee high speed without losing step.
  

What's in the box?

1 x TB6560 1 axis driver board

• Name: Arduino MEGA2560 R3 DIY acrylic case
• Dimensions: 118 x 72 x 18mm
• Weight: 72g
• Material: A level acrylic
• For Arduino MEGA2560 R3 Development Board only

• Total length: about 250M
• Wire type: 30AWG
• Single core wire outer diameter: 0.55mm
• Copper core diameter: 0.25mm.
• Temperature: 80 degrees, single-strand copper core crossing tin, with antioxidant effects.
• Colour: Red

This is a split-core current transformer which is used as an AC current sensor. It is popularly used for current measurement, monitoring and protection for AC motors, lighting equipment, air compressors, home automation etc.

Features

• Opening size: 13 x 13mm
• Rated input current (RMS): 10% - 120% of that is 1A~100A
• Output voltage(RMS): linear output. when the input current is 100A, the output voltage is 1V
• Linearity: ± 3%
• Output connectors: 3.5mm standard three-pin plug
• Lead length: 1m

What's in the box?

1 x Split-Core Current sensor

• Model: PJ-392
• Size(LxWxH): Approx. 22.5mmx 8mm x 8mm/ 0.89x3.15x3.15"

• Breakout Board Schematic
• GitHub Repository

OV7670 image sensor, small size, low operating voltage, and provides all the features of the single-chip VGA camera and image processor. Through the SCCB bus control, you can output the entire frame, sub-sampled, take the window way affect the data resolution of 8 bits. VGA image of the product is up to 30 frames / sec. Users can fully control the image quality, data format and transmission mode. The process of image processing functions including gamma curves, white balance, saturation, chroma, and so can be programmed through the SCCB interface. OmmiVision image sensor applications unique sensor technology to improve image quality by reducing or eliminating the optical or electronic defect, such as fixed pattern noise, tail-blooming, clear and stable color image.

• Low voltage suitable for embedded applications
• Standard SCCB interface compatible with I2C interface
• RawRGB to RGB (GRB4: 2:2, RGB565/555/444), YUV (4:2:2) and YCbCr (4:2:2)output format
• support VGA, CIF, and from CIF to 40x30 the size
• VarioPixel subsampling way eliminate light stripes, automatic black level calibration image quality control including color saturation, hue, gamma, sharpness ANTI_BLOOM
• ISP has eliminate noise and dead pixel compensation function
• Support image scaling
• The lens is the loss of light compensation
• 50/60Hz detection
• The saturation automatically adjust ( UV adjustment)
• edge enhancement automatically adjust
• Noise Reduction automatically adjust

• photosensitive array 640X480
• O voltage 2.5V to 3.0V ( internal LDO to core supplies ) the
• power operation 60mW/15fpsVGAYUV
• Sleep < 20 μ A
• temperature operation from 0 ° C to 50 ° C
• ( 8 -bit) output format ? YUV/YCbCr4 RGB565/555/444 GRB4: 2:2: 2:2 Raw RGB Data
• Optical size of 1/6 "
• field of view angle of 25 °
• maximum Zhen rate 30fps VGA
• Sensitivity 1.3V / (Lux-sec)
• signal to noise ratio of 46 dB
• dynamic range of 52 dB
• browsing mode progressive
• electronic exposure
• area of 3.6 μ mx 3.6 μ m
• dark current 12 mV / s at 60 ° C