Generic1
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 150mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
10pcs LilyPad LED Modules (wearable led's(10))
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up.
Each LilyPad piece was creatively designed with large sew tabs to allow them to be sewn into fabric. Various input, output, power and sensor boards are available.
They're even washable (with special care)!
Specifications
What's in the box?
10 X LilyPad LED Modules
Resources
Each LilyPad piece was creatively designed with large sew tabs to allow them to be sewn into fabric. Various input, output, power and sensor boards are available.
They're even washable (with special care)!
Specifications
- Operating voltage: 3-5V
- Operating current: 40MA
- Weight: 1g (5 by one weight)
- Size: 12.7 mm x 5.2mm x 2.2mm
What's in the box?
10 X LilyPad LED Modules
Resources
LilyPad Power Supply Module AAA Battery Step up to 5V Converter (wearable AAA battery holder)
A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your LilyPad circuit. Good up to 200mA. Short circuit protected.
This board has AAA battery clips but can use an input from 1.2V to 5V.
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable - but be sure to remove the battery!
What's in the box?
1 x LilyPad Power Supply Converter Module AAA Battery Step up to 5V
Need batteries? You will find our battery selection here
This board has AAA battery clips but can use an input from 1.2V to 5V.
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable - but be sure to remove the battery!
What's in the box?
1 x LilyPad Power Supply Converter Module AAA Battery Step up to 5V
Need batteries? You will find our battery selection here
Tri-Colour RGB LilyPad LED Module wearable (wearable RGB module)
Blink any colour you need!
Use the Tri-Colour LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can create any colour. Very bright output.
This is a common anode(positive) design - to turn on a channel you simply need to ground one of the R/G/B pins to illuminate that channel.
LilyPad is a wearable technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
What's in the box?
1 x Lilypad common anode RGB module
Getting started with lillypad tri-color LED
Use the Tri-Colour LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can create any colour. Very bright output.
This is a common anode(positive) design - to turn on a channel you simply need to ground one of the R/G/B pins to illuminate that channel.
LilyPad is a wearable technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
What's in the box?
1 x Lilypad common anode RGB module
Getting started with lillypad tri-color LED
LCD Board 2004 20x4 5V Blue screen display with controller (20x4 character display)
Adding a LCD to any project immediately kicks it up a notch. A great UI addition to any Microcontroller or Raspberry Pi project.
Specifications
What's in the box?
1 x 2004 LCD Display Module
Resources
Interfacing with a 2004 and 1602 LCD
Specifications
- 2004 204 20X4 Character LCD Display Module Blue Backlight.
- Blue backlight
- Fully assembled and tested Serial LCD 20x4 Module
- Display Format: 20 Characters x 4 lines
- Supply voltage: 5V
- The module can be easily interfaced with a MCU
- The module is a low-power consumption character LCD Module with a built-in controller
- Size: approx. 98mm x 60mm x 12mm
What's in the box?
1 x 2004 LCD Display Module
Resources
Interfacing with a 2004 and 1602 LCD
DC 5V WCS1800 Hall Current Detection Sensor Module 35A Precise With Overcurrent Signal LED (WCS1800 Hall Current)
The WCS1800 Hall Current sensor has two functions
Features
What's in the box?
1 x WCS1800 Hall current detection sensor
Resources
Interface
VCC: power positive
DOUT: TLL high/low level signal output
GND: power negative
AOUT: sampling current signal conversion voltage output port
Analog voltage signal output (AOUT)
Relationship between detection current and analog signal output is shown below:
Analog signal output: V0=Vcc*0.5±la*K (la is actual current through current detection pin, and K is linearity)
Eg: Input current is 1A, Vcc=5V and WS1800 linearity is 60mV/A
The above are ideal values. There might be some precision errors.
On/Off output(DOUT)
- current detection
- over current protection (can be preset from 0.5A to 35.0A)
Features
- Operating voltage: DC 5V
- Current detection range: DC +-35A, AC 25A
- Linearity: K=60mV/A
- Limit current range: 0.5A to 35A(for on/off value output)
- Over current signal indicator LED
- Sampling current conversion analog voltage signal output and it can connect ADC; TTL level signal output and it can connect MCU IO port control
- Board size 37mm x 31mm
- Working temperature: 25 to 85C
What's in the box?
1 x WCS1800 Hall current detection sensor
Resources
Interface
VCC: power positive
DOUT: TLL high/low level signal output
GND: power negative
AOUT: sampling current signal conversion voltage output port
Analog voltage signal output (AOUT)
Relationship between detection current and analog signal output is shown below:
Analog signal output: V0=Vcc*0.5±la*K (la is actual current through current detection pin, and K is linearity)
Eg: Input current is 1A, Vcc=5V and WS1800 linearity is 60mV/A
- When the current flows in from positive direction: V0=Vcc*0.5+la*K, V0=(2.5+0.06)V=2.56V
- When the current flows in from negative direction: V0=Vcc*0.5-la*K, V0=(2.5-0.06)V=2.44V
- If it is an AC signal: V0=Vcc*0.5+la*K, V0=(2.5+0.06)V=2.56V
The above are ideal values. There might be some precision errors.
On/Off output(DOUT)
- Make sure the current flows in from the positive direction. Adjust to the desired current warning level.
- LED will be on when current is below the setting and DOUT will be low.
- When the detected current is higher than your setting, the LED will turn off and the DOUT pin will go high.
T8 400mm Lead Screw Set with Shaft Coupling and Mounted Ball Bearing (T8 400mm Lead Screw Set)
These are 4 start 8mm pitch leadscrews with a 200 steps per revolution motor and the 16x microstepping on most common 3D printers. This adds up to 400 steps per mm 3200 steps/ 8mm per rev = 400 steps /mm the same as most 3d Printer lead screws use.
Specifications
Features
1 x Lead screw
1. Put screw nut onto the Lead screw.
Specifications
| Lead screw | |
| Material | stainless steel |
| Diameter | 8mm |
Lead | 2mm |
| Total Length | 400mm |
Screw nut | |
| Material: | brass |
| Diameter | 8mm |
Mounted ball bearing | |
| Material | zinc alloy |
| Bore diameter | 5mm |
Hole diameter | 8mm |
| Total length | 55mm |
| Height | 29mm |
Shaft coupling | |
| Material | aluminium |
| Shaft | 6.35 x 8mm |
| Length | 24mm |
| Diameter | 18mm |
| Quantity | 1 set ( 1 screw 1 Screw nut 2 Mounted ball bearing 1 shaft coupling) |
Features
- Screw mainly used in stepper motors, machine tools, and other CNC equipment.
- Screw directly connected to bearing.
- Suitable for Industrial automation equipment, stepper motor rails, 3D printers, engraving machines, XYZ modules, slider, lifts etc.
1 x Lead screw
1 x Screw nut
2 x Mounted ball bearings
1 x Shaft coupler
Resources
Resources
How to install:
1. Put screw nut onto the Lead screw.
2.Then the 2 Mounted ball bearing separately, install at both ends of the Lead screw.
3. According to the size of you need to adjust the distance between the nut and Mounted ball bearing.
4. Put shaft coupling into the Lead screw beside the Mounted ball bearing.
WS16 AS3935 2.4V to 5.5V Lightning Distance Detector sensor (lightning sensor)
Based on the AMS reference design, this is a breakout board for the AS3935 digital lightning sensor. With a specially tuned antenna, SPI or I2C interfacing and a wide 2.4V to 5.5V standard operating range, this innovative sensor is designed to interface with most current development systems and boards. This includes all of the current Arduino modules!
The AS3935 Franklin Lightning Detector gives you lightning detection for your next weather project. This sensor is capable of detecting lightning up to 40 km away with an accuracy of 1km to the storm front! On the product is a sensitive antenna tuned to pick up lightning events in the 500kHz band. When sensing an event the AS3935 utilizes an interrupt to the interrupt pin, distinguishes between false and real lightning events, and has a number of features to help calibrate lightning detection. For example, there are settings for detecting from indoors or detecting from outdoors, settings to change the threshold for false events, and settings to be alerted only after a certain number of lightning strikes to name a few. We've also written an Arduino Library to get you prepared for that upcoming storm!
The product is capable of communicating over SPI or I2C and sports a Qwiic connector for fast implementation without the need for soldering.
Fully Calibrated Digital Lighting Sensor AS3935 Lighting Detector Breakout Board Module SPI I2C Interface Strikes Thunder Rainstorm Storm Distance Detection Compatible for Arduino RPi
Features
Application - DIY Weather stations
What's in the box?
1 x Lightning Detector sensor
The AS3935 Franklin Lightning Detector gives you lightning detection for your next weather project. This sensor is capable of detecting lightning up to 40 km away with an accuracy of 1km to the storm front! On the product is a sensitive antenna tuned to pick up lightning events in the 500kHz band. When sensing an event the AS3935 utilizes an interrupt to the interrupt pin, distinguishes between false and real lightning events, and has a number of features to help calibrate lightning detection. For example, there are settings for detecting from indoors or detecting from outdoors, settings to change the threshold for false events, and settings to be alerted only after a certain number of lightning strikes to name a few. We've also written an Arduino Library to get you prepared for that upcoming storm!
The product is capable of communicating over SPI or I2C and sports a Qwiic connector for fast implementation without the need for soldering.
Fully Calibrated Digital Lighting Sensor AS3935 Lighting Detector Breakout Board Module SPI I2C Interface Strikes Thunder Rainstorm Storm Distance Detection Compatible for Arduino RPi
Features
- Wide Supply Voltage range : 2.4V - 5.5V
- Lightning Sensing: 40 km Range with accuracy of 1km in 14 steps
- Detects both cloud-to-ground and cloud-to-cloud flashes
- Embedded ‘man made’ disturbance rejection algorithm
- Programmable Detection Levels,Lightning detection thresholds are programmable (outdoor vs indoor, for example)
- Distance to storm estimation
- "Disturber" (false event) rejection algorithm
- Indoor and Outdoor Settings
- SPI and I2C Interfaces
- Qwiic Enabled
Application - DIY Weather stations
What's in the box?
1 x Lightning Detector sensor
Aluminum Alloy HeatSink For Solid State Relay SSR Heat Dissipation (SSR relay heatsink)
Heat sink for solid state relay SSR
Adding an aluminum alloy heat sink will increase the lifespan of your SSR relay, it will help dissipate the heat and protect your relay.
Solid State Relays are ideal for automatic process control application, a must component for temperature controller and other machinery control system.
Specifications
What's in the box?
1 x Solid state relay heat sink
Adding an aluminum alloy heat sink will increase the lifespan of your SSR relay, it will help dissipate the heat and protect your relay.
Solid State Relays are ideal for automatic process control application, a must component for temperature controller and other machinery control system.
Specifications
- Material: Aluminium alloy.
- Size: Roof:50mm x 60mm.Foot:80mm x 50mm.
- Height: 43mm.
- Weight: 96g
- Compatible with: Designed specially for single phase solid state relay.
- Colour: Silver
What's in the box?
1 x Solid state relay heat sink
Power cable USB micro-B to USB-C adapter for Pi4 Black (Pi4 USB micro to C black adapter)
This small adapter allows you to convert an existing micro USB power supply (like the official Raspberry Pi universal power supply for Raspberry Pi 1, 2 and 3) into a USB-C power supply.
Note that when a micro USB power supply is used, the maximum power that can be delivered to the Raspberry Pi 4 will be 12.5W. This means that less power will be available to devices connected to the USB 2.0 and USB 3.0 ports on the Raspberry Pi 4 than when using the new Raspberry Pi 15.3W USB-C power supply.
Specifications
• Female USB-B to Male USB-C adapter
• Compatible with Raspberry Pi 4 Model B (all variants)
• Carry on using your USB micro-B devices
What's in the box?
1 x USB micro-B to USB-C adapter
White USB-C Female To Micro USB Male Adapter (White USB-C to micro B adapter)
This adapter is ideal to convert the 3A type C official power supply to micro B for the Raspberry Pi models Zero, 2 and 3.
Specifications
What's in the box?
1 X White Type C Female To Micro USB Male Adapter
Specifications
- Material: Plastic and Metal
- Colour: White
- Length: 2.3cm
- Connector A: Micro USB Male
- Connector B: Type C Female
What's in the box?
1 X White Type C Female To Micro USB Male Adapter
Toggle switch SPDT (ON-OFF-ON) (switch SPDT (ON-OFF-ON))
Simple ON and OFF switch. This is a panel-mount SPDT (single pole double throw) toggle switch.
This 3 pins toggle switch is great for any project where you have two options to select between. Maybe you'll be selecting between two voltages? Two audio outputs? Two sensor inputs? It's up to you! It's short, sweet, blue, and to the point! The part is marked at 3A 250VAC and 6A 125VAC but we haven't tested it at such high current/voltages and don't recommend it for more than 2A at 24V.
Features
What's in the box?
1 x 3 pins Toggle Switch
This 3 pins toggle switch is great for any project where you have two options to select between. Maybe you'll be selecting between two voltages? Two audio outputs? Two sensor inputs? It's up to you! It's short, sweet, blue, and to the point! The part is marked at 3A 250VAC and 6A 125VAC but we haven't tested it at such high current/voltages and don't recommend it for more than 2A at 24V.
Features
- SPDT 3 Terminal ON-ON 2 - Position Latching Toggle Switch.
- Each switch is assembled with two hex nuts, a flat and a locking washer.
- Easy installation, fits into any 6mm hole.
- Stated Electrical Spec: 3A 250VAC or 6A 125VAC, but we recommend using it at 2A at 24V
What's in the box?
1 x 3 pins Toggle Switch
Raspberry Pi Camera Board Replacement Cable 150mm (Cam csi cable 150mm)
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 150mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
Don't worry though, not all is lost if that cable does happen to break! Replacement raspberry pi camera board cables are available and it's very easy to swap them over!
This replacement cable is 150mm long.
The Raspberry Pi Camera Board Replacement Cable Features:
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 150mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
What's in the box?
1 x CSI ribbon cable
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 150mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
Diagonal electronic cutting pliers thin mouth (thin mouth cutter)
The pliers is designed with a flat mouth, and tight knife edge.
It can easily cut all kinds of soft material below 1.2mm thickness. Wire under 0.8MM.
Suitable for cutting wires, electronic feet, trimming plastic parts etc.
What's in the box?
1 x electronic parts cutting pliers
It can easily cut all kinds of soft material below 1.2mm thickness. Wire under 0.8MM.
Suitable for cutting wires, electronic feet, trimming plastic parts etc.
What's in the box?
1 x electronic parts cutting pliers
12V Lead Acid Battery Digital Charge Level Indicator (battery meter digital)
Charge Level Red Indicator Voltmeter Precise for 12V Lead-acid Battery
Specifications
Indicator
What's in the box?
1 x lead acid LED indicator battery capacity tester voltmeter 12V
Specifications
- Working current:5-15mA
- Eight electricity Level Resolution:10% 25% 40% 50% 60% 75% 90% 100%
- Voltmeter accuracy:1%
- Working temperature: -10 ~ 65 Celsius
- Operating Humidity: 10 ~ 80%
- Dimensions: 48mm x 29mm x 22mm
Indicator
- Battery voltage is greater than 11.1V, 1 led indicator is lit.
- Battery voltage is greater than 11.3V, 2 led indicator is lit.
- Battery voltage is greater than 11.6V, 3 led indicator is lit.
- Battery voltage is greater than 11.9V, 4 led indicator is lit.
- Battery voltage is greater than 12.2V, 5 led indicator is lit.
- Battery voltage is greater than 12.5V, 6 led indicator is lit.
- Battery voltage is greater than 12.9V, 7 led indicator is lit.
- Battery voltage is greater than 13.3V, 8 led indicator is lit.
What's in the box?
1 x lead acid LED indicator battery capacity tester voltmeter 12V
MC4 Solar Crimping Pliers for 2.5-6.0mm PV Solar Panel Cable Black and Red (solar cable crimper)
This is an industrial quality Multi-Contact crimping tool for solar MC4 connectors from 2.5mm - 6mm solar cable. The added lug locator for positioning the lugs makes the job a whole lot easier.
Specifications
What's in the box?
1 x crimping tool
Specifications
- MC3/MC4 solar pv hand crimping tool
- For non-insulated open plug-type connector
What's in the box?
1 x crimping tool
1 Pair MC4 Branch Y Adapter Connectors M/M/F and F/F/M For Solar Panel Cable (Y solar split cable)
MC4 Y branch connectors are Compatible with MC4 solar connectors, for solar cable sizes 2.5 mm2, 4mm2 and 6mm2. Connecting solar panels in series or parallel, is quick and gives a reliable connection of the solar cables to the photovoltaic system.
Specifications
What's in the box?
1 x pair Y connector cables(M/M/F and F/F/M)
Specifications
- Operating Current: 20A (4mm), 30A (6mm)
- Withstanding Voltage: DC1000V
- Contact resistance: <=>
- Insulation resistance:500MΩ
- For single-core cable cross-section: 1.5mm to 4mm
- Cable OD Range: Φ5mm ~ Φ 7mm
- Ambient temperature: -40 ° ~ 105 °
- Protection class: IP67
- Insulation material: PPO, Black
- Contact: Copper cn, sn Nickel
- Flammability rating: UL94-VO
- Terminal connection: Crimp
What's in the box?
1 x pair Y connector cables(M/M/F and F/F/M)
1 pair MC4 3Y Branch parallel connection 30A 1000V solar Panel Cable Connector(MMMF and FFFM) (solar 3way split cable)
Description:
MC4 connectors are single-contact electrical connectors commonly used for connecting solar panels. The MC in MC4 stands for the manufacturer Multi-Contact and the 4 for the 4 mm diameter contact pin. MC4’s allow strings of panels to be easily constructed by pushing the connectors from adjacent panels together by hand and allow for a clean energy transfer between output cables from the solar array and connections to combiner boxes or inverters.
Specifications:
Water and dust proof.
Insulation material: GE PPO
Rated Voltage: TUV 1000 DC/ UL 600V DC
Test voltage: 6KV(50Hz,1Min)
Contact material: copper, tin plated
Contact resistance: less than 0.5 m ohm
Degree of protection: IP67
Pollution Degree: 2
Protection class: Class II
Flame class: UL94-V0
Plug Force: less than 50N
Withdrawal force: more than 50N
Ambient temperature range: -40 ~ 90.
Compatible cable cross sections Solar cable: 2.5mm⊃2; ,4.0 mm⊃2; and 6.0 mm⊃2; (14 awg,12awg,10awg)
Pin dimension: 4.0mm
Package Includes:
1 x pair 3 way split cables(MMMF and FFFM)
MC4 connectors are single-contact electrical connectors commonly used for connecting solar panels. The MC in MC4 stands for the manufacturer Multi-Contact and the 4 for the 4 mm diameter contact pin. MC4’s allow strings of panels to be easily constructed by pushing the connectors from adjacent panels together by hand and allow for a clean energy transfer between output cables from the solar array and connections to combiner boxes or inverters.
Specifications:
Water and dust proof.
Insulation material: GE PPO
Rated Voltage: TUV 1000 DC/ UL 600V DC
Test voltage: 6KV(50Hz,1Min)
Contact material: copper, tin plated
Contact resistance: less than 0.5 m ohm
Degree of protection: IP67
Pollution Degree: 2
Protection class: Class II
Flame class: UL94-V0
Plug Force: less than 50N
Withdrawal force: more than 50N
Ambient temperature range: -40 ~ 90.
Compatible cable cross sections Solar cable: 2.5mm⊃2; ,4.0 mm⊃2; and 6.0 mm⊃2; (14 awg,12awg,10awg)
Pin dimension: 4.0mm
Package Includes:
1 x pair 3 way split cables(MMMF and FFFM)
1pair(2pcs) spanner for MC4 Solar Panel Connector (MC4 solar spanner)
This spanner is a Multi-contact solar connector spanner, suitable for assembling and disassembling of MC4 male/female connectors.
Specifications
What's in the box?
2 x MC4 spanners
Specifications
- Light, small and easy to use
- Double - quick screw down.
- Saved time and manpower for installation.
- Size: 108mm x 30mm x41mm/4.25 x 1.18 x 1.61inch
What's in the box?
2 x MC4 spanners
6DOF MPU-6050 3 Axis Gyro With Accelerometer Sensor Controller Module (6DOF MPU-6050 Gyro Accelerometer)
Features
- Name: MPU-6050 module (three-axis gyroscope triaxial accelerometer)
- 2.54mm pin spacing
- MPU-6050 Accelerometer Gyro
The MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, since it contains 16-bits analog to digital conversion hardware for each channel. Therefor it captures the x, y, and z channel at the same time.
Specifications
- 16bit AD converter-chip, 16-bit data output
- Use Chip: MPU-6050
- Power supply :3-5v (internal low dropout regulator)
- Communication: IIC communication protocol standard
- Gyro Range: ± 250 500 1000 2000 ° / s
- Acceleration range: ± 2 ± 4 ± 8 ± 16g
- Using Immersion Gold PCB, welding machines to ensure quality
- Size: 20mm x 16mm x 10mm
Application
- Motion sensing games
- Augmented Reality
- Electronic Image Stabilization (EIS: Electronic Image Stabilization)
- Optical Image Stabilization (OIS: Optical Image Stabilization)
- "Zero-touch" gestures User Interface
- Pedestrian navigation
- Gesture shortcuts
Market
- Smart phone
- Tablet device
- Handheld games
- 3D remote controller
- Portable navigation devices
What's in the box?
1 x MPU-6050 module
MC4 Compatible Adaptor Diode connection 15A (mc4 diode 15A connector)
MC4 connectors are single-contact electrical connectors commonly used for connecting solar panels. The MC in MC4 stands for the manufacturer Multi-Contact and the 4 for the 4 mm diameter contact pin. MC4s allow strings of panels to be easily constructed by pushing the connectors from adjacent panels together by hand, but require a tool to disconnect them to ensure they do not accidentally disconnect when the cables are pulled. The MC4 and compatible products are universal in the solar market today, equipping almost all solar panels produced since about 2011.
Specifications
What's in the box?
1 x MC4 Compatible Adapter Diode connection 15A
Specifications
- Item no: MC4-D
- Rated voltage: 1000 V
- Rated impulse voltage: 1000 V
- Rated current: 24A - 14 AWG (2.5mm), 30A - 12 & 10 AWG (4mm & 6mm)
- Test voltage: 6 kV (50 Hz)
- Protection grade: IP67
- Insulation material: PC/PA
- Contact material: Copper, silver-plated
- Operating temperature: -40degC ~ 90degC
- Safety class: II
- Flame class: UL94-V0
- Contact resistance: le5mOmega
- Insertion / Withdrawal force: le50N / ge50N
- Suitable for cables: 10, 12, 14 AWG (2.5mm2/4mm2/6mmsup2;)
- Locking system: Snap-in
What's in the box?
1 x MC4 Compatible Adapter Diode connection 15A