Generic1

Sort By:  
R10.35  Inc VAT
R14.90
2pcs Ethernet RJ45 Female Cable Splitter (ethernet splitter(2))

Features

  • Convert and increase your Ethernet connections from 1 to 2 sockets
  • High purity oxygen free copper conductor
  • Polyethylene (LDPE) / PVC insulation
  • High-fidelity design
  • exquisite workmanship
  • easy to use, effective
  • very practical in home and office use
  • Interface: 3 x RJ45 eight core standard jack socket
  • Size: 42mm x 35mm x 20mm
  • Uses: extended, dock two network lines into a longer network cable



Specifications

  • High purity oxygen free copper conductor
  • Polyethylene (LDPE) / PVC insulation
  • High-fidelity design
  • exquisite workmanship
  • easy to use, effective
  • RJ45 eight core standard jack socket


What's in the box?

2 x RJ45 Cable splitter modules(NO cables)

Note: If you want both ports to be able to access the Internet at the same time, you need to have both split adapters plugged in at the same time

R78.52  Inc VAT
R109.90
Raspberry Pi GPIO Screw Terminal Board Header For Raspberry Pi (Gpio Terminal rpi header)
Features

  • Tiny size & solidly built
  • Well made terminal block
  • Legible miniscule printing of the labels of each of the GPIO pin's function
  • Secure connection to the Raspberry Pi


What's in the box?

1 x Terminal block
1 x Screwdriver
1 x Acrylic board
2 x Nuts
2 x M2.5x11 brass standoffs
4 x M2.5x5 6 brass standoffs
6 x Screws

Resources 

Wiki - Raspberry Pi GPIO Terminal Board












(* Raspberry Pi NOT included - ONLY GPIO screw terminal*)





(* Raspberry Pi NOT included - ONLY GPIO screw terminal*)


R257.00  Inc VAT
HDMI female To HDMI Female Extension Adapter 1080P (HDMI f2f adapter)
Looking to extend your HDMI cable, without purchasing an extra long cable? This adapter is used to connect two HDMI male cables and is compatible with 1080P, 3D

Specifications

  • HDMI
  • 1080p
  • female to female
  • black
  • extension adapter

What's in the box?

1 x hdmi adapter
R20.17  Inc VAT
HDMI male To HDMI male Extension Adapter 1080P (HDMI m2m adapter)
If you need to change the gender of you HDMI connection, this is the connector you need.

Specifications

  • HDMI
  • 1080p
  • male to male
  • black
  • extension adapter

What's in the box?

1 x hdmi adapter
R89.90  Inc VAT
2:1 Black Heat Shrink Tubing 3mm per meter (black heat shrink 3mm)
Description:

Heat-shrink tubing is a shrinkable plastic tube used to insulate wires, providing abrasion resistance and environmental protection for stranded and solid wire conductors, connections, joints and terminals in electrical work.

Specifications:

Shrinkage Ratio: 2:1 (will maximum shrink to 1/2 its supplied diameter)
Cutting method: Scissors or sharp knife

What's in the box?

1 x 1m heat shrink tube
R7.90  Inc VAT
2:1 Black Heat Shrink Tubing 5mm per meter (black heat shrink 5mm)

Heat-shrink tubing is a shrinkable plastic tube used to insulate wires, providing abrasion resistance and environmental protection for stranded and solid wire conductors, connections, joints and terminals in electrical work.

Specifications

Shrinkage Ratio: 2:1 (will maximum shrink to 1/2 its supplied diameter)
Cutting method: Scissors or sharp knife

What's in the box?

1 x 1m heat shrink tube

R9.90  Inc VAT
10pack Red female ring Insulated Lugs Crimp Terminal RV1.25-4 (Lugs red ring RV1.25-4)

Ring terminals connect two or more wires to a single connection point, by fitting the open face of the terminal over a stud. They create a solid connection as the ring that is fitted over the stud cannot come loose or fall off. This removes the possibility of the ring terminal disconnecting. They are widely known for the semi-permanent connections that they create. To make ring terminals even better, they can easily be used with two or more wires depending on the application. Ring terminals are the most secure type of tongue style terminal available and are commonly chosen for their durability, ease of use, and longevity in tough conditions.

Specifications

  • Conductor cross section: 0.5-1.5 mm2
  • Bolthole: 4mm

What's in the box?

1 x pack of 10 lugs

You will find our lugs selection here

R11.90  Inc VAT
10pack Red female spade Insulated Lugs Crimp Terminal FDD2-250 6.3mm (Lugs red spade female FDD2-250)

Female Spade lugs provide a quick and reliable solderless electrical connection. These single conductor connectors are made to connect with a predefined connector size or male quick connects.

Specifications

Conductor cross section: 0.5-1.5 mm2

What's in the box?

1 x pack of 10 lugs

You will find our lugs selection here

R26.90  Inc VAT
10pack Blue Ring Insulated Lugs Crimp Terminal RV2-4 (Lugs blue ring RV2.5-4)

Ring terminals connect two or more wires to a single connection point, by fitting the open face of the terminal over a stud. They create a solid connection as the ring that is fitted over the stud cannot come loose or fall off. This removes the possibility of the ring terminal disconnecting. They are widely known for the semi-permanent connections that they create. To make ring terminals even better, they can easily be used with two or more wires depending on the application. Ring terminals are the most secure type of tongue style terminal available and are commonly chosen for their durability, ease of use, and longevity in tough conditions.

Specifications

  • Conductor cross section: 1.5-2.0mm2
  • Bolthole diameter: 4mm

What's in the box?

1 x pack of 10 lugs

You will find our lugs selection here

R11.90  Inc VAT
10pack Blue Fork Insulated Lugs Crimp Terminal SV2-4 (Lugs blue fork SV2-4)

Fork Terminals are a type of connector used to attach a wire or wires to a stud, bus bar, or another part of an electrical system.

These Lugs are insulated to ensure safe and secure connections to an electrical device.

Specifications

  • Conductor cross section: 1.5-2.5 mm2
  • Bolthole diameter: 4mm


What's in the box?

1 x pack of 10 lugs

You will find our lugs selection here

R15.90  Inc VAT
10pack Blue Insulated Lugs Crimp Joiner Terminal BV2.5 (Lugs blue join BV2.5)

Joiner Terminals are a type of connector used to attach a wire or wires to a stud, bus bar, or another part of an electrical system.

These Lugs are insulated to ensure safe and secure connections to an electrical device.

Specifications

Conductor cross section: 1.5-2.5 mm2

What's in the box?

1 x pack of 10 lugs

You will find our lugs selection here

R18.90  Inc VAT
8-bit WS2812 5050 RGB LED Ring Development Board (RGB ring 8)

Specifications

  • Voltage: DC 5V 
  • Colour: RGB 
  • Outer radius of 2 x 28mm
  • Inner radius of 2 x 8mm 

Please note: Soldering will be required to connect your wires
 
What's in the box?
 
1 x 8 Bit WS2812 5050 RGB LED Driver Development Board

R19.90  Inc VAT
10Pcs 5mm Led Flashing Green Diffused (10Pcs 5mm led flash green)
These are general purpose 5mm Flashing Green LED with diffused lens and good brightness.

Specifications

  • Brand: CHANZON
  • Lens Size: 5mm Diameter
  • Lens: Colour Lens
  • Emitting Colour: Green Flash
  • Viewing Angle: 20 Degree (Colour Lens)
  • Forward Voltage: 3.0-3.2V
  • Current: 20mA
  • Frequency: 1.5HZ
  • Flicker Frequency: 90 Times / Minutes
  • Polarity: Anode (Longer Leg) | Cathode (Shorter Leg)

What's in the box?

10 x Flashing LEDs
R10.35  Inc VAT
R14.90
10Pcs 5mm Led Flashing Red Diffused (10Pcs 5mm led flash red)
These are general purpose 5mm Flashing RED LED with diffused lens and good brightness.


Specifications

  • Brand: CHANZON
  • Lens Size: 5mm Diameter
  • Lens: Colour Lens
  • Emitting Colour: Red Flash
  • Viewing Angle: 20 Degree (Colour Lens)
  • Forward Voltage: 3.0-3.2V
  • Current: 20mA
  • Frequency: 1.5HZ
  • Flicker Frequency: 90 Times / Minutes
  • Polarity: Anode (Longer Leg) | Cathode (Shorter Leg)

What's in the box?

10 x Flashing LEDs
R10.35  Inc VAT
R14.90
LM35DZ Precision Centigrade Temperature Sensor (LM35DZ temp sensor)

The LM35-series devices are precision integrated-circuit temperature sensors, with an output voltage linearly proportional to the Centigrade temperature. The LM35 device has an advantage over linear temperature sensors calibrated in Kelvin, as the user is not required to subtract a large constant voltage from the output to obtain convenient Centigrade scaling. The LM35 device does not require any external calibration or trimming to provide typical accuracies of ± ¼ °C at room temperature and ± ¾ °C over a full −55°C to 150°C temperature range. Lower cost is assured by trimming and calibration at the wafer level. The low output impedance, linear output, and precise inherent calibration of the LM35 device makes interfacing to readout or control circuitry especially easy. The device is used with single power supplies, or with plus and minus supplies. As the LM35 device draws only 60 μA from the supply, it has very low self-heating of less than 0.1°C in still air. The LM35 device is rated to operate over a −55°C to 150°C temperature range

Features

• Calibrated Directly in Celsius (Centigrade)
• Linear 10-mV/°C Scale Factor
• 0.5°C Ensured Accuracy (at 25°C)
• Rated for Full −55°C to 150°C Range
• Suitable for Remote Applications
• Low-Cost Due to Wafer-Level Trimming
• Operates From 4 V to 30 V
• Less Than 60-μA Current Drain
• Low Self-Heating, 0.08°C in Still Air
Non-Linearity Only ±¼°C Typical
• Low-Impedance Output, 0.1 Ω for 1-mA Load

Applications

• Power Supplies
• Battery Management
• HVAC
Appliances

What's in the box?

1 x LM35DZ temperature sensor

R19.90  Inc VAT
MK8 0.4mm Copper M6 Thread Extruder Nozzle For 3D Printer (MK8 print nozzle 0.4mm)
Description

Original 0.4mm Copper M6 Thread Extruder Nozzle For Ender-3 CR-10 V2 CR-10S Pro Ender-5 CP-01 CREATITY 3D

Specifications

1. Material: Copper
2. Size: 13mm x 6mm
3. Weight: 2g
4. Nozzle thread: M6
5. Nozzle accuracy: 0.4mm


What's in the box?

1 x 0.4mm Nozzle




R16.90  Inc VAT
ESP32 For Wemos D1 Mini For Arduino UNO R3 D1 R32 WIFI Bluetooth Development Board CH340 4M Memory One (Wemos D1 R32)
Features

  • Small volume, easily embeded to other products
  • DC 5V-12V 
  • 1 analog input(3.2V max input)
  • A Micro USB connection
  • Compatible with for Arduino
  • D1 R32=WiFi Bluetooth UNO
  • Size: 6.8x5.3cm/2.68x2.09inch

What's in the box?

1 x Wemos D1 R32 board
Arduino compatible
R139.23  Inc VAT
433 Mhz Superheterodyne RF Receiver and Transmitter Modules (tx rx modules 433mhz)
The kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. The frequency is 433MHz. It is very popular for remote control systems, such as Remote control rolling gates, robotics, smart home, etc.

Short antenna for Transmitter
Long antenna for Receiver

About the transmitter module (square shape)

  • Model: WL102-341
  • Material: Plastic Metal
  • Colour: shown as pictures
  • Size: 16×12×1mm
  • Operating frequency: 433.92 MHz
  • Mains input voltage range: 2.0V-3.6V
  • Shutdown mode current is less than 1uA
  • Transfer rate: up to 20KHz
  • Launch distance: 20-100 meters
  • External antenna: 25cm ordinary multi-core or single-core line
  • Temperature range: -45℃~85℃

About receiver module (rectangular shape)

  • Model: RX470-4 (RX470-4 is WL101-341 upgraded version, more stable performance, faster data transfer)
  • Material: Plastic Metal
  • Colour: shown as pictures
  • Size: 30×9×1mm
  • Operating frequency: 433.92 MHz
  • Mains input voltage range: 2.2V-5V
  • Working current: Type: 2.1mA (Requirement:VDD=5V) ; Type: 2.1mA (Requirement:VDD=3V)
  • Quiescent Current: 1uA
  • Temperature range: -40℃~85℃
  • External antenna: 32cm single core wire, wound into a spiral

What's in the box?

1 x 433MHz RF transmitter module
1 x 433MHz RF receiver module
2 x 433MHz spring antennas (Short antenna for Transmitter; long antenna for Receiver.)

Resources

Configure and read a 433Mhz RF Transmitter With Receiver on the Raspberry Pi
R42.90  Inc VAT
3d Printer CNC Kit, UNO R3, RAMPS 1.4, Mechanical Switch Endstop, DRV8825 Motor Driver, Nema 17 motor (Uno full 3 motor cnc kit)
CNC Shield Version 3.0 for Arduino

GRBL 0.9 compatible
4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Working Voltage: 12-36V DC
Max. Working Current: 2.5A
RAMPS 1.4

Mechanical Switch Endstop

Red: VCC (ramps )
Black: GND (ramps -)
Green: SIGNAL (ramps s)

DRV8825 Stepper Motor Driver

Size: 1.5mm x 2mm
Upgraded from A4988
Maximum Current: 2.5A
32 Subdivision: 1, 1/2, 1/4, 1/8, 1/16, 1/32
4-layer PCB board for better heat dissipation
Suitable for driving stepper motors up to 8.2V~45V, 2.5A

Nema 17 Stepper Motor

Model: 17HD48002H-22B
Rated Current/phase: 1.7A
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Latest CH340G CNC Shield expansion board Version 3.0 for Arduino, and compatible for GRBL 0.9.

UNO R3 Board

MCU: ATmega328
USB interface: ATmega16U2 cable with USB .

This is a professional sensor kit for UNO R3. New and upgraded, we provides various components or sensor module, with which you will find it easy for you to complete every experiments or learning. All these are packaged in a portable case, easy to carry and storage.

What's in the box?

1 x CNC Shield V3
1 x UNO R3 MEGA328P CH340G with USB Cable
5 x DRV8825 Stepper Motor Driver with Heat Sink
5 x RAMPS 1.4 Mechanical Switch Endstop
5 x 3pin Cable (70cm)
3 x Nema 17 Stepper Motor
3 x Nema 17 Mounting Bracket
R2,699.90  Inc VAT
MK8 0.4mm Copper M6 Thread Extruder Nozzle For 3D Printer 5 pack ((5x) MK8 print nozzle 0.4mm)

Features

  • Material: Copper
  • Size: 13mm x 6mm
  • Weight: 2g
  • Nozzle thread: M6
  • Nozzle accuracy: 0.4mm

What's in the box?

5 x 0.4mm Nozzles

R49.90  Inc VAT
R84.50
Per Page      201 - 220 of 408