Generic3
You will need this stand for your solder iron. Simple yet practical helping tool during soldering your electronic components. Soak the sponge in water before use.
Note: This stand comes in loose parts, you need to do some assembly.
Features
- Low-cost soldering iron/gun stand
- Simple yet practical
- Sponge Dry: 50mm x 35mm x 1mm
- Sponge Soaked: 55mm x 37mm x 6mm
What's in the box?
1 x Metal base
1 x Screw and Nut
1 x Spring holder for soldering iron
1 x Sponge
Resources
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
Male to Female Jumper Wire Cable Line Multicolored 100mm
Specifications
- Multicolored
- 100mm
- Male to Female
What's in the box?
1 x Ribbon of 40 lines
Resources
Female to Female Jumper Wire Cable Line Multicolored 100mm
Specifications
- Multicolored
- 100mm
- Female to Female
What's in the box?
1 x Ribbon of 40 lines
Resources
Male to Male Jumper Wire Cable Line Multicolored 100mm
Specifications
- Multicolored
- 100mm
- Male to Male
What's in the box?
1 x Ribbon of 40 lines
Resources
Our 4xAA battery holder is perfect for hobbyists looking for a reliable power source for their DIY electronics projects. Made from durable materials, it's easy to install and use with simple connections. Its compact design makes it portable, so you can work on your projects anywhere. Order yours today and take your projects to the next level!
Features
- Brand new and good quality
- Material: Plastic and metal
- Weight: 15g
- Color: black
- DC 5.5mm x 2.1mm Jack
- The case can hold 4 x AA batteries (battery is NOT INCLUDED)
- Connection: Series, so the output voltage will be 4 x battery voltage
- Output Voltage = 6.0VDC typical if you are using normal AA
- Output Voltage = 4.8VDC typical if you are using rechargeable NiMH
- Size: 5.7cm x 6.2cm x 1.5cm
- Perfect for use with your EDU:BIT
What's in the box?
1 x Quad AA Battery Holder
Need batteries? You will find our battery selection here
This DIN rail bracket is a reliable mounting accessory designed to secure electronic components, circuit boards, and terminal blocks onto standard DIN rails commonly used in industrial automation, electrical enclosures, and control panels. It ensures stable and organized installation, preventing movement or disconnection due to vibrations or mechanical stress. Made from high-quality insulating plastic, it provides excellent durability and protection against environmental factors, ensuring long-term performance in industrial settings.
With its pre-drilled holes and included screws, this bracket allows for quick and hassle-free installation, reducing assembly time and maintenance efforts. It is compatible with various industrial components such as relays, power supplies, PLC modules, and circuit protection devices, making it an essential accessory for control systems and wiring applications. Whether used in electrical cabinets, automation systems, or industrial machinery, this DIN rail bracket enhances organization and efficiency in any setup.
Features
- Material: PA66V0
- Wiring Method: Track Wiring
- Colour Classification: DRG-01
- Compatible with M3x10mm screw
- Supports standard DIN rails dimensions (Width: 35mm Height:7.5mm)
What's in the box?
2 x DIN Rail Bracket
4 x M3 Screw (10mm)
ATmega328 is commonly used in many projects and autonomous systems where a simple, low-powered, low-cost micro-controller is needed.
The Arduino Compatible Nano V3 development board is a microcontroller board based on the Arduino Nano
Specifications
- Microcontroller Atmel ATmega328P
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7V ~ 12V
- Input Voltage (limits): 6V ~ 20 V
- Digital I/O Pins: 14 (of which 6 provide PWM output)
- Analog Input Pins: 8
- DC Current per I/O Pin: 40mA
- Flash Memory: 32KB (ATmega328) (of which 2 KB used by bootloader)
- SRAM: 2KB (ATmega328)
- EEPROM: 1KB (ATmega328)
- Clock Speed: 16MHz
What's in the box?
1 x Arduino Compatible Improved Version Nano V3.0
Resources:
Getting started with Arduino products
Both ends of this cable have a JST PH 2mm pitch 2-pin plug. Between the two, 200mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together!
This is an A-A cable, that means both ends have the same polarity, you can flip the cable around and it will always connect pin 1 to pin 1.
Perfect to use with your LiPo Amigo Pro (LiPo/LiIon Battery Charger) to power your project.
What's in the box ?
1 x JST-PH 2-pin Jumper Cable
Note: This logic level shifter breakout comes with loose headers. You will have to solder them yourself.
If you have ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be! The logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. Each level converter can convert 4 pins on the high side to 4 pins on the low side, with power supply pins on each side.
The usage of the level converter is very straightforward. The board needs to be powered from the two voltage sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the "HV" pin, low voltage (3.3V for example) to "LV", and ground from the system to the "GND" pin.
This module requires you to supply it with power from both the higher voltage level and the lower voltage level. Connect the higher voltage source to pin "HV" and its ground to pin "GND" near the "HV" pin. Also, connect the lower voltage source to pin "LV" and its ground to pin "GND" near the "LV" pin.
For example, if you were connecting your Arduino (5V signals) to an ESP8266 (3.3V signals), you would connect the "HV" pin on the module to the 5V supply pin on your Arduino and the "GND" pin near the "HV" pin to the "GND" pin on your Arduino. Then, you would connect the "LV" pin on the module to the 3.3V power source that is supplying power to the ESP8266 and connect the "GND" pin near the "LV" pin to the 3.3V power supply's ground. You would then connect the signal pin from your Arduino to one of the signal pins on this module (for example, pin "HV1"), and then you would connect the desired signal pin on the ESP8266 to the corresponding pin on this module ("LV1" if the higher voltage signal is connected to "HV1").
These are 4 Channel devices (works great for I2C or SPI) and will work with all microcontrollers, Arduino, Raspberry Pi, Intel Edison, etc. Use this module to connect two devices of different digital voltage levels. For example: connecting an Arduino (5V device) to an ESP8266 (3.3V device).
The logic level converter comes complete with loose header pins and can be used directly on a breadboard.
- Convert 4 pins on the high side to 4 pins on the low side or vice versa
- With 2 rows, 6 pins per row
- No. of channels: 4
- Power from two voltage sources (high and low); high voltage goes to the HV pin and low voltage to the LV pin
- Mutual transform between 3.3V and 5V
- Digital Logic only, NOT Analog voltage.
- Useful for IIC Protocol communication
- Compatible with Arduino, PIC, Raspberry Pi, etc
- Breadboard Compatible
- Pinout labeled on modules
- Dimensions (excluding pins): 15.2mm (0.6") length x 12.7mm (0.5") width x 2.5mm (0.1") height
- Weight: 1.2g (0.04oz)
What's in the box?
1 x 4-Channel Logic Level Shifter
Is it time to upgrade or repair your 3D Printer's pulley wheels with these high quality TEVO Pulleys made from POM (Polyoxymethylene/acetal)
Specifications
- Type: Pulley wheel
- Bore: 5mm
- Size: about 24mm x 10mm
- Material: POM
- With Bearings: YES
- Bearing: 625zz bearing
What's in the box?
1 x Wheel with Bearing
This is a new design ABS case to protect your Raspberry Pi 4 Model B computer, it is only compatible with your Raspberry Pi 4 Model B, does not support other versions. Also supports a dc 5v cooling fan.
Features
- ABS material.
- Easy to install.
- All ports and slots of the case match with Raspberry Pi 4 Computer Model B perfectly.
- Supports a DC 5v extractor cooling fan.
What's in the box?
1 x ABS Case for Raspberry Pi 4 Model B
1 x Cooling Fan 30mm x 30mm x 7mm
4 x Heat Sinks(new add on to this case)
Resources
This is a low cost Red Laser Diode in Copper Casing. The Mean Wave Length is 650nm and the Power Rating is 5mW.
Specifications
- Output Power: 5mw
- Wavelength: 650nm
- Working Voltage: 3~5V
- Working Temperature: +10 ~ +40 Celsius
- Laser Shape: line / point / cross
- Focusable: Yes
- Material: Metal
- Dimensions : 12mmx12mmx40mm
What's in the box?
1 x 3V 650nm 5mW Red Dot Diode Laser Heads
PLA plastic is a biodegradable thermoplastic, made from renewable resources like sugarcane or corn starch or soybeans. When it melts, there is no smell, so it is very comfortable to use in the home or classroom.
Specifications
- High strength, good toughness
- Density is small, when printing larger volume model lighter, save money
- Cost-effective as it can be processed in a wide range temperature
- PLA has a low shrinkage rate, even print larger models perform well
- To be applied to a variety of 3D printer, Makerbot, UP plus, Mendel, Prusa, series, etc
- Environmental friendly PLA material, no bubble exited, accurate filament diameter
- Non-toxic and no smell
Features
- Colour: 3 Colours (Random)
- Quantity: 3
- Material: PLA
- PLA: 190 - 220° C
- Diameter:1.75mm
- Length: 9 meters (3 meters each color)
- Usage: 3D Printing Pen
- Section Shape: Round
What's in the box?
1 x 3 Colors 1.75mm PLA Filaments for 3D Pen-9 Meters
Resources
Want to print a spool holder that clips onto your 3D pen?
Check out Thingiverse - This device allows you to store and use lengths of 1.75mm filament for a 3D pen. The unique mini spool is designed to prevent the filament from unraveling under its own spring tension. The parts can be welded together with your 3D pen.