Generic4
Voltage: DC 5V
Colour: RGB
Outer diameter 85mm, 70mm inner diameter
Soldering will be required to connect your wires
What's in the box?
1 x 24 Bit RGB LED Driver Development Board
You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts every 3 seconds or so. It's a very handy tool for testing USB devices, checking load levels and debugging battery chargers and boost converters.
Specifications:- USB 1.x and 2.x - all data speeds. Does not have USB v3 pins so USB v3 connections will automatically downgrade to v2
- Working Range: 0~3A, 3.5~7VDC
- Resolution: 10mV / 10mA
- Operating Temperature: 0-60ºC
- Contents:
- Camera Board 360 Gooseneck Mount V2
Dimensions:
- 21mm x 53mm x 15mm / 0.8" x 2.1" x 0.6"
- USB Plug: 13mm / 0.5"
- Weight: 16.2g
1 x USB Voltage and Current Meter
Description:
Colour-coded GPIO pins that make locating that ground or power connection you need super simple!
These 40-pin 2x20 male headers from our friends at The Pi Hut can be used on a Raspberry Pi Zero and are colour-coded for your prototyping convenience.
You'll never have to search for a ground pin again!
The colour coding is nice and simple:
- Red = 5V
- Yellow = 3V3
- Black = GND
- Blue = DNC (Reversed I2C)
For hard-mode try installing the header the wrong way round and throwing away your normal pin reference! ;-)
- Gender: Male
- No. of Contacts: 20
- No. of Pins: 20
- Termination: Straight Pins Solder Tail
- Size: 2.54mm
- Row Positions: Double Row
What's in the box:
1 x Colour-coded GPIO Header
Complete set for wide range of network products such as Access Points, Routers, IP cameras, modems, switches, embedded computers or other network devices such as D-Link, Ovislink, Senao, Wline, Router BOARD, WRAP boards and other devices using passive POE injection.
Connector Barrel size is 2.1mm (5.5 x 2.1 mm)
Power Pins 4,5 and 7,8 -
1. It is very simple to connect a passive PoE.
On the lower part, we connect the Ethernet RJ connector of passive PoE to the PC, Hub or Switch and connect the power adapter to the power socket.
2. On the opposite end (RJ socket) we connect the Ethernet cable leading to the far end.
3. At the far end, we connect the end of the Ethernet cable to the RJ45 socket and connect the power connectors and the Ethernet to the powered equipment.
The equipment is now connected by them.
Input / Output Specifications
- Supports Voltage: 5V, 12V, 24V, 48V
- Max Output Current 0.4A Max.
- Over Current Protection None
General Specifications
- Operating Temperature 0° ~ 45°
- Storage Temperature -30oC ~ 70oC
- CASE OF MATERIAL PVC
- Ethernet Date Rate 10/100Mbps
- Ethernet Cable TIA/EIA 568 Cat.5
- Humidity Up to 90%
- Weight: 24g*4DC
- Plugs 2.1mm x 5.5mm x 12mm
- Length 155mm
What's in the box?
With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have.
Inside the plastic tube is a gold plated slip ring for 6 wires. There are six color coded wire sets made of 26 AWG and no matter how you twist the assembly, they will remain in continuity. Each of the wire sets can carry up to 2A at up to 240VAC or 240VDC. There's a 44mm (1.7") diameter flange with mounting holes to make it easy to attach or you can cut it off with a hacksaw and drill/machine as you wish it seems to just be ABS plastic. Rated to rotate up to 300 RPM (but you can probably go faster if you don't mind a reduced life and/or noise).
Note: Wire colors may vary.
TECHNICAL DETAILS
Rated voltage: 240VAC/240VDC
Rated current: 2 Amp
6 x 6" long 26 AWG wires
What's in the box?
1 x Slip Ring with Flange - 22mm Diameter-6 Wires
Description
This lovely little lens set is the best way to easily expand the field of view of your Raspberry Pi camera!
This lens kit means that you can use your camera module in many exciting ways:
- 1x Wide-angle lens: Ideal for capturing those landscape shots/night sky time-lapses
- 1x Macro lens: Beautiful close-up images of anything from insects to circuit boards
- 1x Fish-eye lens: Security systems and crazy 180° FOV shots
Perfect for taking shots from anywhere from your desk to the edge of space this lens comes with a back splint which means you can also use it with other camera devices such as your mobile phone.
Each lens screws into the clip which fits perfectly onto your camera module.
Features
- Compatible with the known universe *
- High-class glass lens, high clarity.
- No vignetting or dark circle.
- Lens covers to protect the camera lenses
- Material: ABS & aluminum alloy
- Compatible with most of the official Raspberry Pi Camera Modules
What's in the box?
1 x camera clip
3 x screw on lenses
The camera comes with a 289mm (11.4") long cable so you can extend and mount your Pi away from the camera. Like the Raspberry Pi Camera Board, it attaches to your Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses the dedicated CSI interface, which was designed especially for interfacing to cameras. The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data.
The camera is connected to the BCM2835 processor on the Pi via the CSI bus, a higher bandwidth link which carries pixel data from the camera back to the processor. This bus travels along the ribbon cable that attaches the camera board to the Pi.
The sensor itself has a native resolution of 5 megapixel, and has a fixed focus lens onboard. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p30, 720p60 and 640x480p60/90 video.
CSI camera port works with Raspberry Pi 3/4 B
Sensor: OV5647, 5MP 2592x1944 pixels
Pin: 22
Peach: 0.5mm
AVDD: 2.7-3.3V (Typical2.8V)
DVDD: 1.45-1.8V
DOVDD: 1.7-3.3V
Lens Structure: 4P (650nm)
EFL: 3.52
FNO: 2.8
FOV: 70 degree
Output Format: YUV or RAW RGB
1080p video at 30 FPS (or 60 FPS at 720p, 90 FPS at 480p)
F2.9 lens, 3.4 mm focal length
53.50 degrees horizontal, 41.41 degrees vertical field of view
Approx. dimensions of circuit and camera: 60 x 11.5 x 4.5mm
The new Raspberry Pi OS release includes the new Picamera2 Python camera interface.
What's in the box?
1 x camera module
Support
Please download the camera user guide here.
Specifications
Compatible with Model B Raspberry Pi boards (Pi 4, 3B+, 3, 2, B+)
OV5647 Sensor
Compatible with libcamera and raspicam commands
Compact size - just 35mm long!
Includes foam gaskets for creative mounting
Images up to 2592x1944
Video up to 1920x1080
Sensor: OV5647
Pixels: 5MP
Focal length: ~3.9mm
CMOS size: 1/4"
Field of View: ~73°
Aperture: F2.4
Depth of Field: ~20cm
Distortion: < 1.5%
Still Image: up to 2592x1944
Video:
1920 x 1080p @30
1280 x 720p @60
640 x 480p @60
640 x 480p @90
The new Raspberry Pi OS release includes the new Picamera2 Python camera interface.
What's in the box?
1x Mini Camera Module
Resources
- How to Install & Use the Raspberry Pi Camera Module (different camera but the process and commands are the same)
- Libcamera and the legacy Raspicam stack
- Libcamera introduction and usage
- Raspicam (legacy) introduction and usage
- OctoPrint for 3D print monitoring
- MotionEyeOS Raspberry Pi CCTV
CH340 is the new popular USB to UART converter/bridge for maker. It is being widely used in many development boards which includes:
- NodeMCU with CH340
- Maker UNO
This is a cable that embeds CH340 in it and extended the useful pins out to female headers.
The cable is the easiest way ever to connect to your microcontroller/WiFi router serial console port. Inside the big USB plug is the CH340 USB <-> Serial conversion chip and at the end of the 1-meter cable are four-wire:
- Red is power, or VCC, 5VDC
- Black is ground or 0V
- White is RXI input to USB's UART port, Receive input of USB's UART
- Green is TXO output of USB's UART port, Transmit output of USB's UART
The power pins provide 5V @ 500mA direct from the USB port and the RX/TX pins are 5.0V logic for interfacing with the most common 5V logic level chipsets.
Because of the separated pin headers, this cable is ideal for powering and connecting up to the debug/login console on the ESP32-CAM as ESP32's IO pins are 5V tolerant. We have tested this USB to UART converter with ESP32-CAM and it works fine.
This is easier to use than an FTDI cable in many cases because the wires are separated. Note that we call this a "TTL cable" (since that's what they're called) but technically it's CMOS logic.
It will appear as COM port after being plugged into the computer/laptop's USB port and after driver installation (1st and one time only).
Note: This cable is NOT SUITABLE for Arduino re-programming such as a BBFuino, Pro-Mini, etc. because it does not have the DTR/RTS wire necessary for initiating the bootloader reboot sequence.
- USB to UART TTL
- CH340 IC
- Extended the Power and UART pins:
- Red = V_USB, 5V
- Black = Gnd
- White = USB_RX
- Green = USB_TX, 5V logic
- V_USB is 5.0V while TX and RX are 5.0V too
- Cable length: 1 meter
1 x CH340 USB to TTL Serial Cable
- CH34X driver (Please ensure the Cable is plugged into computer USB port during driver installation)
- Windows (V3.5 Mar2019)
- Mac OS (V1.5 Mar2019)
- Linux (V1.5 Mar2019) (Normally is readily installed)
- CH34X Driver - Get the latest driver from the factory
This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. It's short (30cm between connectors), so perfect for mounting your Raspberry Pi, Beagle Bone, Arduino etc. into a box!
The jack half has two mounting 'ears' with M3 screws installed, 8mm apart. The ears are flexible so the holes don't have to drilled very precisely.
Our Panel Mount USB Cable Features
- Specially Manufactured for ModMyPi for use with the Raspberry Pi & Other Microcontrollers
- Length between connectors: 30cm
- Colour: Black
- 28AWG
- USB A Male to Panel Mount USB A Female
- M3 Mounting Ears
What's in the box?
1 x USB A Male to Panel Mount USB A Female
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 1 meter cable are four wire - red(power), black (ground), white (RX) into USB port, and green (TX) out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chipsets.
Because of the separated pin plugs, this cable is ideal for powering and connecting up to the debug/login console on the Raspberry Pi or BeagleBone Black. Connect the pins as shown to power the Pi or BBB and establish the RX/TX link.
If you are running Windows 7/8/10 etc, check this tutorial page with links to drivers for both PL2303 and CP2102
If you are running Mac OS X, check this tutorial page with links to drivers for both PL2303 and CP2012
If you are running Linux, drivers are already included in the kernel, no need to install anything!
Also handy for hacking WiFi routers to install alternate OS's, or nearly any other 3.3V logic serial port. This is easier to use than an FTDI cable in many cases because the wires are separated. Note that we call this a "TTL cable" (since that's what they're called) but technically it's CMOS logic.
This cable is not good for Arduino re-programming such as a BBFuino, Pro-Mini, etc. because it does not have the DTR/RTS wire necessary for initiating the bootloader reboot sequence.
- USB to UART TTL
- Red = V_USB, Black = Gnd, White = USB_RX, Green = USB_TX
- V_USB is 5V while TX and RX is 3.3V
- PL2303HX IC.
- Cable length: 1 meter
What's in the box?
1 x USB to RS232/TTL PL2303HX cable adapter module
This panel mount HDMI (Male to Female) extension cable will allow you to extend an HDMI connection and secure it to an enclosure!
Perfect for placing your Raspberry Pi in a secure box, the panel mount uses two #4-40 (M3) screws to attach the female socket end! The panel mount screw holes are 26.9mm apart.
This cable is 0.4m long (about 16 inches), and is a V1.4 CEC enabled cable.
Specifications:
• 1x HDMI male connector
• 1x HDMI panel mount female port
• Offers 0.4m cable length
• Customize your solutions – mount a HDMI port on your PC or Pi through an available HDMI female connector
• Guaranteed reliability
What's in the box?:
1 x HDMI panel mount cable
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 1000mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 1000mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
Normally a male connector having exposed pins which are molded into a plastic base. Common Headers are 0.1 inch spacing, pin-to-pin. Female connectors having the same spacing are used to interface.
Commonly used in electronics projects involving a controller and a breadboard to create short term wiring between components. With this kit you can make your own lengths and make up multiple pins connections.
Features:
Great for electronics prototyping.
Compatible with Arduino and Raspberry Pi projects.
Box size(L*W*H): 17 x 10 x 2.2 cm
Package includes:
1 x Plastic Box (Contains 610 PCS Connector Kit)
Note:
Artificial pick, please allow an error of 2%, thank you.
Perfect for soldering, perfect for robotic ,electronic, and restoration projects.
It can hold two CR2032 coin batteries.
Features:
Output: 6V
Color: Black
Model: For CR2032 x 2
What's in the box?
1 x CR2032 Battery enclosure (Batteries not included)
Need batteries? You will find our battery selection here
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 150mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 150mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
The Raspberry Pi Camera Module comes fully assembled with a 15-Way 2000mm flat, flex cable that plugs directly in the Raspberry Pi CSI port. Unfortunately the included cable is quite fragile, and can break if twisted or bent too far.
Don't worry though, not all is lost if that cable does happen to break! Replacement raspberry pi camera board cables are available and it's very easy to swap them over!
- Direct Replacement for the Raspberry Pi Camera Board Cable
- 2000mm Overall Length
- 1mm Pitch
- 15 Way Flat Cable
- Conductor: Tin plated copper
- Insulation: White PVC
- Supporting tape: Blue polyester
- UL rating: UL2896
- Temperature rating: 80°C
- Voltage: 30V
- Flame test: VW-1, FT1, FT2
- CSA Standard: CAN/CSA-22.2 No.210.2
1 x 2000 mm Raspberry Pi Camera cable
- 1