Search

Creality Hi Ceramic Heating Block, High Thermal Conductivity, Quick-swap Nozzle, 300℃ High Temperature Resistance

The BME680 is a "4-in-1" sensor that measures temperature, humidity, barometric pressure, and volatile organic compounds (VOC) gas. It is a favorite for weather stations and air quality monitors

The GY-BMI160 is a highly integrated, low-power 6-axis inertial measurement unit (IMU) designed for precise motion tracking. It combines a 16-bit digital, 3-axis accelerometer and a 3-axis gyroscope into a single compact module, making it an ideal choice for space-constrained and battery-sensitive applications.

This 5-Port Passive Hub board has 5 vertical JST SH 1mm connectors in a row, all with the power, ground and SDA/SCL pins connected. There are also breadboard breakout pins if you need them. Use this hub to add as many I2C devices to the bus as you need.

This 4-wire cable is a little over 150mm long and fitted with JST-SH (Qwiic/STEMMA QT) female 4-pin connector on one end, and female jumper wires on the other.

This 4-wire cable is a little over 300mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

These are handy for extending a Stemma QT or Qwiic cable if you don't have one long enough for your project, or to protect a port if you're regularly swapping out sensors/dev boards. The pin connections are 1-1, matching both sides.

This 4-wire cable is a little over 200mm long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.

Rotary encoders are soooo much fun! Twist em this way, then twist them that way. Unlike potentiometers, they go all the way around and often have little detents for tactile feedback.

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for your Raspberry Pi Pico board. Reset button? Yes! STEMMA QT / Qwiic connector for fast I2C? Indeed.

This Qwiic/STEMMA GPIO connector from Ozzmaker allows you to easily connect Qwiic or STEMMA enabled modules to a Raspberry Pi, without the need for soldering.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Animate your LEGO® Technic™ models using the high-performance LEGO Powered Up Large Motor. Specially engineered to handle heavy-duty tasks, this motor delivers the raw torque needed to drive complex gear setups, heavy lifting assemblies, or precise steering mechanisms.

Single-cell lithium base battery charger & protection module. The charging will be via a micro B connector. Lithium base battery includes Li-po and Li-ion battery as the charging and discharging characteristic is similar.

The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Raspberry Pi. The SHIM design allows you to plug directly into the Pi's I2C bus with no soldering required and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other HATs!

Ideal for your dc electronic projects.

The AMS1117-3.3V Step-Down Power Module is a compact, plug-and-play Low Dropout (LDO) linear regulator designed to easily convert a 4.5V–7V input into a stable, clean 3.3V DC output.