Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
R159.90  Inc VAT
DC 9V 1A Battery Button Power Cable Tieline For Arduino (9VDC Batt arduino power clip)

Description:

This is a DC 9V Battery Button Power Cable Tieline For Arduino

Barrel adapter is negative on the outside

Package includes:

1 x DC 9V Battery Button Power Cable 
R9.90  Inc VAT
Switched Battery Box 2xAA (3V) (3V AA switch battery box)

This battery box is designed for use as a nice switchable, portable power pack, and fits any two alkaline or rechargeable AA batteries in series. The body is moulded in black ABS Resin and has a slide on detachable lid which can be locked for extra security through use of a small provided screw. It even includes a very useful miniature on-off slide switch which is very handy for wiring to projects that don't have a switch! Connection is via two flexible stranded red (positive) & black (negative) 26AWG wire leads, which are approximately 150mm in length.

The two batteries are held in series, for a nominal output of 3V DC (AA Batteries @ 1.5V each).
 
Specification
  • Battery Cell Size AA
  • Number of Cells 2
  • Body Material ABS Resin
  • Height 19.0 mm, Length 68.0 mm, Width 33.0 mm
  • Terminal Type Wire Lead
  • Type Battery Box
  • Weight 0.01900 kg
R34.90  Inc VAT
Switched Battery Box 4xAA (6V) (switch batt box 4xAA)

This battery box is designed for use as a nice switchable, portable power pack, and fits any four alkaline or rechargeable AA batteries in series. The body is moulded in black ABS Resin and has a slide on detachable lid which can be locked for extra security through use of a small provided screw. It even includes a very useful miniature on-off slide switch which is very handy for wiring to projects that don't have a switch! Connection is via two flexible stranded red (positive) & black (negative) 26AWG wire leads, which are approximately 150mm in length.

The four batteries are held in series, for a nominal output of 6V DC (6.4V when fresh, 4V when dead), and 4.8V DC for rechargeables (5.2V when fully charged, 4.4V when discharged). Using rechargeables will make this work nicely with nearly any 5V project, with alkalines you may want to put a 1N4001 in series to drop the voltage from 6V down to 5.3V.
 
Specification
  • Battery Cell Size AA
  • Number of Cells 4
  • Body Material ABS Resin
  • Height 19.0 mm, Length 69.0 mm, Width 64.5 mm
  • Terminal Type Wire Lead
  • Type Battery Box
  • Weight 0.03300 kg
R41.90  Inc VAT
Panasonic CR2032 Lithium Coin Cell Batteries (CR2032 coin battery)
Replacement battery for OSMC remote.


Product Details

Lithium Coin Button Battery, CR Series

CR type lithium button batteries offer long shelf life and are ideal for items such as watches, memory support and cameras. ercury free.

Key Features

  1. Non-rechargeable lithium coin cells
  2. CR type suitable for intermittent high load applications
  3. Long shelf life
  4. Commonly used in applications like watches, calculators, remotes and cameras



Coin & Button Cells, Lithium

All cells in this range have a voltage of 3V.

Technical specification for all types
TypeDiameter (mm)Height (mm)
CR102510.02.5
CR121612.51.6
CR122012.52.0
BR122512.52.5
CR1612161.2
CR1616161.6
CR1620162.0
CR1632163.2
CR2016201.6
CR2025202.5
BR/CR2032203.2
BR2325232.5
BR/CR2330233.0
CR2354235.4
CR245024.55.0
CR247724.57.7
CR3032303.2
R14.90  Inc VAT
6 x AA Battery Holder with DC2.1 Power Jack for Arduino (battery holder 6xAA)
Description:

Holds 6 x AA batteries (not included) which can do 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells
Power supply for dc projects.
With DC05 power supply jack
Cable Length: 12cm

Specifications:

Voltage: 9V
Material: Plastic
Power: 6 x 1.5V AA batteries
Color: Black
Net weight: 25g

Package includes:

1x Battery case with DC2.1 power jack
R28.75  Inc VAT
PR 1.3-12 12V 1.3Ah Sealed Lead Acid Battery (12V 1.3Ah lead/Acid Batt)
12 Volt 1.3Ah Lead Acid Battery

Ideal for robotics and hobby related projects.

Housing size: 95mm x 42mm x 52mm
Weight 510mg
R109.90  Inc VAT
DIY DC 7.4V 2 Slot 18650 Battery Holder Battery Box With 2 Leads ROHS Certification (18650 twin battery holder)
Features:

Rated voltage: DC 7.4V
Material: ABS

Product certification: ROHS
Size: 77.7mm X 40.21mm X 21.54mm

Package includes:

1 x 2 slot 18650 battery holder
R26.90  Inc VAT
4x5 18650 Battery Pack Spacer (18650 battery pack spacer)
Specifications:
Product name:Battery pack spacers
Material: ABS
Color: Black
Weight: 18g
Size: Approx. 103mm x 93mm x 8mm (L x W x H)

Features:
Made of ABS material, lightweight and durable
Fits 20 x 18650 batteries
Makes your battery pack Solid and Reliable!

Package Contents:
1 x Battery Holder spacer

More info on battery packs available at https://www.youtube.com/watch?v=hwhqn4BmC2I
R34.90  Inc VAT
Plastic Battery Case For 4 x 18650 Batteries (4x18650 battery box)
Descriptions:

Battery type: 4 pcs 18650 Case Holder
18650 Battery Holder Case with 6 inch leads for soldering / connecting
Takes 4 standard size 18650 batteries side by side to form a compact battery of 3.7V rechargeables
Keep your batteries organized and protected
Batteries not included

Package includes:

1 x Battery Holder Case for 4 x 18650
R124.90  Inc VAT
12V 7Ah Sealed Lead Acid Battery (12V 7Ah lead/Acid Batt)
12 Volt 7Ah Lead Acid Battery

Ideal for robotics and hobby related projects.

Housing size: 150mm x 65mm x 100mm
Weight 1982mg
R209.90  Inc VAT
Liitokala Lii-402 Micro USB DC 5V 4Slots 18650/26650/16340/14500 Battery Charger (4 bay battery charger)
PLEASE NOTE:

Misusing or mishandling a lithium-ion battery may cause a FIRE or EXPLOSION which can result in INJURY or DEATH.


Specifications:

Product name: Liitokala Lii-402 Micro USB 4Slots Battery Charger
Input : Micro USB DC 5V/2A
Output: 1.42V
              4.2V±0.05V
              3.65±0.05V
              4.35±0.05V
Current: 2000mA*1 1000mA*2 700mA*3 500mA*4
Constant voltage, cut-off current: less than 100mAh
Standby current: less than 15mAh

Compatible with:
Ni-MH/Cd
AA/AAA/A/SC Sizes
3.7V Li-ion battery including
26650,22650,26500,18650,18490,17670,17500,16340,14500,10440

Size: 112mm x 90mm x 30mm (L x W x H)
Weight:  150 grams (incl. micro cable)

USB Output function
1. 0pen-circuit voltage of USB output : 4.9-5.3V; and the 4th slot is fixed for the USB discharge power source
2. Output current: 1000mAh
3. Open circuit current: <1mAh
4. The corresponding voltage is 4.75-5.25V under 1000mAh current
5. Cut-off voltage for discharge protection: 3.0±0.1V

You will need a USB micro B cable power supply for this charger.

Package includes:
1 x Liitokala Lii-402 Micro USB 4Slots Battery Charger
1 x USB Cable
R379.90  Inc VAT
Li-ion Battery HAT for Raspberry Pi, 5V Output, Quick Charge (Battery hat zero)

Overview

The Li-ion Battery HAT integrates SW6106 power bank management chip, allows providing 5V regulated power supply to your Pi from a 14500 battery, makes the Pi becomes a portable device. It will charge the battery as well, supports bi-directional quick charge. This module can be used as a universal mini power bank, also works with other 5V devices.

Features

  • Onboard SW6106 chip, supports bi-directional quick charge, supports multi quick charge protocols like PD/QC/FCP/PE/SFCP
  • Lithium battery protection circuitry, provides reverse protection, over charge/discharge protection, over current protection, and short circuit protection
  • Onboard indicators: quick charge, warning, and power capacity

Specifications

  • Output voltage: 5V
  • Applicable battery: 3.7V 14500 lithium battery (4.2V when full charged)
  • Dimension: 65mm × 30mm
  • Mounting hole size: 3.0mm

What's on Board


  1. Raspberry Pi GPIO connector: for connecting Raspberry Pi
  2. SW6106 power management chip
  3. USB Type-C connector: battery charge/power output
  4. USB Type-A connector:power output
  5. Micro USB connector:battery charge
  6. Raspberry Pi power switch
  7. Battery warning indicator: on when the battery is reverse
  8. Battery power capacity indicator: 5x LEDs to indicate the power capacity and charging status
  9. Quick charge indicator: on when quick charging
  10. 14500 battery holder

Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/Li-ion_Battery_HAT

R289.90  Inc VAT
CR2032 Button Battery Holder Case With On/Off Switch 6V (CR2032 battery enclosure)
Description:

Button/Coin compact design enclosure with On and Off Switch.
Perfect for soldering, perfect for robotic ,electronic, and restoration projects.
It can hold two CR2032 coin batteries.

Features:

Output: 6V
Color: Black
Model: For CR2032 x 2

Package includes:

1 x CR2032 Battery enclosure (Batteries not included)
R15.90  Inc VAT
4 In 1 Charger Discharger Boost 5V 2.1A Module for 3.7V 4.2V Battery DIY Mobile Power with Button (charge/discharge power module)
Description
trigger: input LOW(grounding)
Single Chip Using: If Small load KEY connect 20S single chip and supply with input LOW, the module will work well.

Charge voltage: DC 4.5V-5.5V(Recommend DC 5V)    
Charging current: 0-2.1A
Charge quiescent current: 100uA
Full charge voltage: 4.2V+-1%
Discharge current: 0-2.4A
Discharge quiescent current:50uA
Discharge conversion efficiency: MAX 96%
Output voltage: 5V
Output current: 0-2.4A
Operating ambient temperature: -20°to +85°
Size: 25x16x4mm
Weight: 2.3g
PCB board design: Immersion Gold
Battery protection: OCP/OVP/SCP/OTP


About module pin
1 VIN: charge port +
2 GND: charge port -
3 BAT: Battery +
4 GND: Battery -
5 GND: output -
6 VOUT: output +
7 KEY: trigger


Note:
1.In discharging mode(charging mode KEY function invalid), trigger KEY one time,output open; trigger two times, output close.
2.Output will open automatically if you connect load. If load below 50MA, the module will turn off output port; if load over 50MA, output port will always open.
3.Allow charging and discharging at the same time(output voltage should below 5V.Stop charging and stop discharging,you should reactivation the module.)


Package Includes:
1 x power module
1 x button

---

1. Charge/Discharge: All cables
2. Charge: Connect power supply and battery
3. Discharge: Connect battery and output





R99.90  Inc VAT
MPPT Solar Regulator 12/24 V, Tracer A 30A, Input 100V (Tracer3210A) (EPEVER MPPT solar charger)
Tracer A series adopts positive design with LCD and advanced MPPT control algorithm with 99.5% efficiency. The products can track the MPP point fast and accurately in any situation which will improve energy efficiency and obtain the maximum solar energy.

The original solar controller made by EPsolar for GWL/Power.

Features:

  • Advanced MPPT technology
  • High tracking efficiency no less than 99.5%
  • Peak conversion efficiency of 98%
  • Ultra-fast tracking speed
  • Accurately recognizing and tracking of multiple power point
  • Multi-function LCD displays system information intuitively
  • User programmable for battery types, load control etc.
  • 3-Stage charge with PWM output
  • Common positive grounding design
  • RS485 port with industrial standard MODBUS open architecture
  • Fully programmable function via PC software or remote meter

Electronic protections:
  • PV reverse polarity protection
  • PV short circuit protection
  • PV over current alarm protection
  • Battery overcharge protection
  • Battery over discharge protection
  • Battery reverse polarity protection
  • Load short circuit protection
  • Load overload protection
  • Controller overheating protection

MPPT function is a smart tracking algorithm that maximizes the energy from the solar PV module(s) and charge the battery. Solar Controler also control of low voltage disconnect function (LVD) will prevent the battery damage from battery over discharging.

Wiring and working of controller

Please NOTE: In case of using LiFePO4 batteries is recommended to check the status of voltage during charging and discharging with another external electronics.

Advance features:

  • Support for LiFePO4 and LiFeYPO4 batteries was tested successfully
  • Auto recognition of 12 / 24V system.
  • Innovative Maximum Power Point Tracking technology to optimize using the solar system.
  • Function of automatic recognize day/night.
  • Dual Timer function with 1-15 hours option for street lights
  • Support for Sealed, Gel and Flooded battery option of LiFePO4 battery
  • Temperature sensor and output for external temperature sensor
  • Electronic protection: over charging, over discharging, overload, short circuit.
  • Reverse protection: any combination of solar module and battery.

Included USB monitoring cable

This MPPT regulator can be monitored using a PC with WINDOWS. Check the Solar Controller Monitor for Tracer series (RS-485/USB) to learn about a simple way to monitor and store the log of the charging and discharging history.


Remote Battery Temperature sensor included





Parameters



Max. power (W)720
Weight (kg)1,2
Max output current (A)30
Height (mm)228
Width (mm)164
Depth (mm)55
Nominal Voltage (V)12/24
Max. input voltage (V)100
TechnologyMPPT


Documents

190201_Regulator_Tracer_A_30A_REG-TR3210A_A4.pdf

tracerA-manual.pdf


R2,128.31  Inc VAT
R2,899.90
Avoidance tracking Smart Robot Car Chassis Kit Speed Encoder Battery Box 2WD Ultrasonic module For Arduino kit (Aduino robot car)
Please Note: Some drilling will be required. You might need to add a few standoffs and screws to build it the way you want it.

This complete robot car kit includes the arduino as well. Just add batteries and code. Great for beginners to learn how to code using sensors and motion on the Arduino boards

Pdf manual available at http://www.cs.columbia.edu/~sedwards/presentations/robot-car-instructions.pdf


Get more details at https://create.arduino.cc/projecthub/hda-robotics/project-1-2wd-obstacle-avoiding-robot-390ef8



Package Includes: 
  • Car chassis x 1 
  • Car Wheels x 2 
  • DC Gear Motor x 2 
  • 20 line gun code disk x 2 
  • Fasteners (high intensity black acrylic) x 4 
  • Caster x 1 
  • Four battery box x 1 
  • Quality Rocker Switch x 1 
  • Assembly drawing x 1
  • Several screws and nuts
  • V5 shield x 1
  • UNO R3 x 1
  • SG90 x 1
  • FPV x 1
  • L298N x 1
R479.90  Inc VAT
Translucent Hard Plastic Case Holder Storage Box for AA AAA C battery (batteries not included) (battery storage box)
Please note: Batteries are not included.

Description :


Made of hard material, durable and environmental
Fit for different kinds of batteries, such as AAA, AA.
Light weight
Can store 20 pcs AA size, 14pcs AAA size.
Individually spaced design

Specifications :  

Material : Plastic
Colour : Clear white
Size : 150mm x 90mm x 55mm (LxWxH)
Suitable for : Home, office, hobby, DIYproject
 
Package includes :  

1 x AA/AAA battery Plastic Case
R209.90  Inc VAT
LilyPad Coin Cell CR2032 Battery Holder (switch wearable CR2032 holder)
Description:

Sure, your flashing, chip-tune playing t-shirt is really cool at the party... but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you've even sewn a LilyPad slide switch in-line. Wouldn't it be nice if there was just a switch on the battery? Well look no further.

This LilyPad Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off your project and save batteries. This slide switch is the same as is found on the LilyPad slide switch board, so it's not easy to accidentally turn off or on.

Just like the original Coin Cell Battery Holder, this simple board holds a 20mm coin cell battery (such as a CR2032) and gives you 4 connection points (two positive and two negative) for sewing into your project.


Package Includes:

1 x LilyPad Coin Cell Battery Holder CR2032 Battery Mount Module
R10.90  Inc VAT
LilyPad Power Supply Module AAA Battery Step up to 5V Converter (wearable AAA battery holder)
Description

A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your LilyPad circuit. Good up to 200mA. Short circuit protected.

This board has AAA battery clips but can use an input from 1.2V to 5V.

LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable - but be sure to remove the battery!


Package Includes

1 x LilyPad Power Supply Converter Module AAA Battery Step up to 5V
R59.90  Inc VAT
Relay Board (KT relay kit)
Product Description

This is a versatile relay board kit that can easily be configured via jumpers and trimmer potentiometers to do a range of tasks.

Most sensor and switches can be connected to the input of the board and the trigger level set for the input device. This can be inverted if required, then there is the option to feed this straight to the relay or a timer of up to 25 minutes can be used. Irrespective of the state of the invert jumper whenever the sense LED goes from off to on the timer restarts.#

The board can run off any voltage from 4.5 to 6 volts.

The output cans switch DC or mains.

This datasheet details what the board does and how to use it along with some worked examples. A more detailed set of information including the build instructions & how to configure the kit can also be downloaded.

Click here to download the full teaching notes pdf_icon.gif

WARNING: Using mains electricity can be dangerous and should only be attempted by qualified electricians.

This kit includes:

  • 3 x 100Kohm resistors
  • 3 x 220ohm resistors
  • 1 x 47Kohm resistors
  • 1 x 1Mohmpotentiometer
  • 1 x 10Mohm potentiometer
  • 2 x 1N4001 diodes
  • 2 x 5mm red LEDs
  • 1 x 100uF capacitors, electrolytic
  • 1 x 4.7uF capacitors, electrolytic
  • 1 x 2N7000 n-channel FET
  • 2 x 2 way terminal blocks
  • 1 x 3 way terminal blocks
  • 1 x LM324 operational amplifier IC
  • 1 x 14 pin IC holder
  • 2 x 3 way pinstrip
  • 2 x Jumpers
  • 1 x Relay
  • 1 x Relay board PCB

PCB dimensions: 86.5mm x 49mm.

This kit is supplied as a pack of parts and requires soldering.

R159.90  Inc VAT
Per Page      1 - 20 of 43