Search
Search Criteria
Products meeting the search criteria
- 40 Pin Double Row (2x20) Socket Connector
- Extension for the Raspberry Pi GPIO Connectors
- Pitch 2.54mm
- Fully Tested on the Raspberry Pi Model B
This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. It's short (50cm between connectors), so perfect for mounting your Raspberry Pi, Beagle Bone, Arduino etc. into a box!
The jack half has two mounting 'ears' with M3 screws installed, 8mm apart. The ears are flexible so the holes don't have to drilled very precisely.
Our Panel Mount USB Cable Features:
- Specially Manufactured for ModMyPi for use with the Raspberry Pi & Other Microcontrollers
- Length between connectors: 50cm
- Colour: Black
- 28AWG
- USB A Male to Panel Mount USB A Female
- M3 Mounting Ears
1.Make Your Own Ethernet Cables
2 Protect your cable ends with these snag free boots for RJ-45
3.Helps to Keep Cables from Snags and Rips
4.Extend the Life of your Cable
Specifications:
1. Material: Rubber
2. Dimensions: 27.5×15×15mm (L × W × H)
3. Color: Gray
Package Included:
10 x RJ45 Cat 5e 6 Connector Boots
Quantity: 1 Pcs
Color: As per pic
Single Size: Approx.34x21x16mm
Features:
Quick and economical.
Straight through configuration.
This coupler allows two ethernet cables with RJ45 connectors to be connected together so that the signal will pass straight through.
It is a cheap and simple way to extend network cables and is ideal for moving networked computers without uprooting existing cables.
Package Included:
1 x RJ45 Straight Through Ethernet LAN Cable coupler
Cables are not included
Type : Banana plug or lug
Solid hard plastic shell
Quantity : 4pcs ( 2 x red and 2 x black )
Easy installation with screws and nuts
Suitable for : 4mm banana plugs, lugs or bare wire
Package Included :
2 pair of speaker binding posts (2 x red and 2 x black)
As a connector, the terminal block is an important module in the electric industry.
It makes it easy to connect wires to your pcb.
Electrical Properties:
Rated voltage: 300V
Rated current: 16A
Contact resistance: 20mΩ
Insulation resistance: 5000MΩ/1000V
Withstanding voltage: AC1500V/1Min
Mechanical Properties:
Temp. Range: -30℃~+120℃
Max Soldering: +250℃ for 5 Sec
Torque: 0.5Nm
Specifications:
Screws: M2.5 steel Zinc plated
Contact: phosphor bronze Ni plated or stainless steel
Pin header: Brass, Tin plated
Housing: PBT, UL94V-0
Pitch: 5.08mm Poles: 2P
Color: Blue
Quantity: 5
Package includes:
5 x 2 pin Terminal Blocks
Simple & Professional appearance for power cabling
Easier for camera installation, save time and more securer cable connection
5.5mm x 2.1mm Female power plug connector
Clearly marked positive and negative to avoid reversal.
Package Includes:
1 x Pair Male Female 12V DC Power Plug Jack Adapter Connector
Connector Type:Male Plug
Material(External):PVC Plastic
Color: Black + Green
Size:2.1 x 5.5 mm
Internal diameter of the plug: 2.1mm
External diameter of the plug: 5.5mm
Package includes :
1 x DC Power Male Jack Plug Connector
RJ45 Connector Modular Plug
8 Pin Plug for UTP Cat5, Cat5e solid or stranded wire solid or stranded Cable.
Gold plated leads for better data transmitting and higher signal strength
Color: Clear
Quantity: 10pcs
Package Includes:
10 x RJ45 CAT5 Modular Plug Network Connector
Overview:
This addon board connects to a Raspberry Pi Zero (RPi0) or Zero W (Wireless) via pogo pins to provide a full sized, USB Type-A connector.
You can use Raspberry pi zero or Raspberry pi zero W as a U disk via P4wnP1 P4wnP1 project, and you can use it as a BadUSB device too.
Specifications:
Size: 6g
Weight: 8.0 x 3.0 x 0.5cm (with USB port)
6.5 x 3.0 x 1.2mm (PCB size)
More info available at http://www.raspberrypiwiki.com/index.php/Raspberry_Pi_Zero_W_USB-A_Addon_Board
Package includes:
1x USB-A Addon Board
Rated voltage: 1000 V
Rated impulse voltage: 1000 V
Test voltage: 6 kV (50 Hz)
Suitable for cables: 10, 12, 14 AWG (2.5mm/4mm/6mm)
Rated current: 24A - 14 AWG (2.5mm), 30A - 12 & 10 AWG (4mm & 6mm)
Protection grade: IP67
Contact material: Copper, silver-plated
Insulation material: PC/PA
Operating temperature: -40degC ~ +90degC
Safety class: II
Flame class: UL94-V0
Contact resistance: le5mOmega
Insertion / Withdrawal force: le50N / ge50N
Locking system: Snap-in
2 x Solar Cable Female Connectors
This pre-built Edge Connector Breakout Board for the micro:bit gives access to all the important pins on the bottom edge of the micro:bit.
Looking to do more with your micro:bit? Unlock its potential with this pre-built version of our Edge Connector Breakout Board! This breakout board has been designed to offer an easy way to connect additional circuits and hardware to the pins on the edge of the micro:bit. It provides access to all of the micro:bit processor pins allowing a lot of extra functionality to be added. The datasheet (below) includes a helpful diagram explaining the function of every pin on the micro:bit.
This Edge Connector Breakout Board for the micro:bit gives access to all of the important pins on the bottom edge of the micro:bit. 21 pins are broken out in total; providing additional I/O lines, direct access to buttons A and B, the LED matrix outputs and the I2C bus. Please refer to the datasheet below for more details.
The micro:bit pins are broken out to a row of pin headers. These provide an easy way of connecting circuits using jumper wires. The SCL and SDA pins are separated at the edge of the board (solder pads) providing easy identification. The PCB includes a prototyping area with 3V, 0V and unconnected rows that can be soldered to. This allows the easy connection of switches, sensors and any pull-up or pull-down resistors etc. as required.
To use the breakout board the micro:bit should be inserted firmly into the connector as shown below:
Note:
- This product is supplied with straight double row PCB pin headers already soldered to the breakout board
Features:
- Features a dedicated pin strip for quick and easy prototyping
- Breaks out 21 pins from the edge of the micro:bit
- Dedicated prototyping area with 3V and 0V rows
- Labelled pins and clear, straightforward documentation
Contents:
- 1 x Edge Connector Breakout Board for the micro:bit, pre-built
Dimensions:
- Length: 60mm
- Width: 40mm
- Height: 11.8mm
Video available at https://youtu.be/bzm4zepbGAc
Requires:
- 1 x micro:bit
Resources:
| Brand | Excellway® |
| Model | JP02 |
| Material | Plastic, Metal |
| Type | 5.5mm x 2.1mm Male |
| Outside Diameter | 5.5mm |
| Inside Diameter | 2.1mm |
| Length | 4.5cm |
| Operating temperature | -50 ~ 65 ℃ |
| Connector Polarity | + inside and outside - |
| Scope | DC power supply security, monitoring equipment, LED lights, Arduino, switches and other devices. |
Package includes:
Description:
This listing includes: 10 pairs of MC4 parallel connectors for 3 solar panels. (FFFM and MMMF)
Application:
It can be used for connecting 3 solar panels in parallel.
Advantage:
1). Easy to use
2). TUV certification
Specifications:
Description | Parameter |
Rated Voltage (VDC) | 1000 |
Rated Current (A) | 40A |
Low Ambient Temperature (°C) | -40°C |
Upper Ambient Temperature (°C) | +90°C |
Degree of Protection (IP Code) | IP67 |
Contact Material | Copper |
Insulation Material | PPO+PA |
Certification | TUV |
Connection resistance | <= 1m Ω |
Insertion force | <=60N |
Withdraw force | >=60N |
Flame class | UL94-VO |
As a connector, the terminal block is an important module in the electric industry.
It makes it easy to connect wires to your pcb.
Electrical Properties:
Rated voltage: 300V
Rated current: 16A
Contact resistance: 20mΩ
Insulation resistance: 5000MΩ/1000V
Withstanding voltage: AC1500V/1Min
Mechanical Properties:
Temp. Range: -30℃~+120℃
Max Soldering: +250℃ for 5 Sec
Torque: 0.5Nm
Specifications:
Screws: M2.5 steel Zinc plated
Contact: phosphor bronze Ni plated or stainless steel
Pin header: Brass, Tin plated
Housing: PBT, UL94V-0
Pitch: 5.08mm Poles: 3P
Color: Blue
Quantity: 5
Package includes:
5 x 3 pin Terminal Blocks
Product configuration: 4mm x 2mm Teflon tube
Product thread: M6 thread
Product use: Extruder
Material: Brass
Package Inlcudes:
1 x Creality 3D® pneumatic Connector
Package Includes:
2pin = 10Sets =20PCS
3pin = 10Sets =20PCS
4pin = 10Sets =20PCS
5pin = 10Sets =20PCS
Pin Connector Terminal :150PCS
1.Product: 4 Terminal Speaker Connector Plate
2.Type: Push Release Type
3.Material: Plastic, Metal
4.RoHS: Yes
5.Rated Load: AC 50V 3A
6.Wire Range: AWG 24-16
7.Temperature: -40 to 55 C
8.Contact Resistance: <= 0.03 Ohm
9.Insulation Resistance: >= 100M Ohm
10.Withstand Voltage: AC 500V 1 Minute
11.Actuating Force: 1 Kgf
12.Colour Polarity Coding: Red/Black
13.Life: >10000 Times
14.Position:4 Way (1 row)
15.Mounting Hole Center Distance: 60mm/ 2.4inch
16.Pin Quantity:4 pin
17.Size:70x24x20mm
Features:
1. 4 pins, 4 positions, spring load design, push type speaker terminal board.
2. The spring loaded terminals ensure a solid connection.
Package includes:
1 x Speaker Terminal Strip
Description:
This testing wire with alligator clips will help transmit DC current to other multi-meters or other usage.
Made from copper wire and well-made PVC.
It can pass 3-5A(max) current during your testing work.
High performance, lower resistivity and durable, fast and stable, high-speed output current
Specifications:
Color: Red and Black (V+ and V-)
Power: 5V
Working current: 3-5A
Lines size: 2x18AWG
Cable Length: 332mm
Package Contents:
1 x USB Male Alligator test lead
- Four-lead motor connector XH2.54 white terminal 4pin-6pin motor line
- 3D Printer Stepper Motor Line
- Connector : 4pin to 6pin
- Length: 50cm
Package Includes:
1 x 3D Printer Stepper Motor Line 50cm Length