Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
R99.90  Inc VAT
R53.90  Inc VAT
R159.90  Inc VAT
R104.90  Inc VAT
TT-02 DIY Car Model TT Motor w/ Wheel - Black + Yellow (robot wheel and motor)
Quantity 1 Piece(s)/pack
Color Yellow + black
Material ABS + iron
Compatible Models Robot, gun toy, four wheel drive toy, aircraft toy, vibration products
Other Feature Motor speed: 100 per minutes; Torque: 4.5kg. cm1; Voltage: 3~6V; Non-loaded revolving speed: 100RPM; Non-loaded current: 60mA; Torque (6V): 4500mg cm
Packing List 1 x Motor
1 x Wheel
R69.90  Inc VAT
Tracking Robot Car Electronic DIY Kit With Reduction Motor (DIY track robot kit)


Tracking Robot Car Electronic DIY Kit With Reduction Motor





The assembly steps:


Step 1: Welding circuit

Soldering part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted

Step 2: Mechanical assembly

The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire.

Step 3: The installation of a photoelectric circuit

Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test.

Step 4: Vehicle debugging

The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side.

Note: We don't supply any manuals please note this before you buy it.

Package includes:

1 x Electronic DIY Kit (batteries are not included)





R199.90  Inc VAT
Arcade Kit DIY Replacement Parts USB Encoder to PC Joystick and Buttons (Arcade kit)
Features :

Each encoder can support one joystick.
Use them to DIY your own Arcade game machine.
The Zero Delay USB Arcade Encoder is a fully compatible plug and play solution, simply plug in your joystick and buttons into the encoder, plug the USB cable into the Pi, map your buttons in RetroPi and away you go - it really is that easy! You can use multiple encoders at the same time, so they're great for multiplayer arcade machines!
 
Specifications :

Joystick Size: Approx. 95x60x100mm
Encoder Board Size: Approx. 85x35mm
USB Cable Length: Approx. 1.8m
Colour: Red

We have tested this unit on Raspberry Pi using Retropie and a Windows 7 PC using MAME.
 
Package includes :

1 x Encoder Board
1 x USB Cable
1 x 5 pin Cable for Joystick
1 x 5 Pin Joystick
8 x 30mm Push Buttons
2 x 24mm Push Buttons
13 x Cables for Buttons

Get Retropie on the Raspberry Pi
ModMyPi setup guide
R639.90  Inc VAT
DIY Arcade 8 Way Joystick Replacement Part (DIY Joystick)
Features :

8 way operation.
Mountable in control panels.
Easy to operate with high sensitivity.
Use it to DIY your own Arcade gaming machine.
 
Specifications :

Top Ball Diameter: Approx. 35mm
Total Size: Approx. 95x60x100mm
 
Package includes :

1 x Joystick
Cables not included
 
Learn about RetroPie
Compatible with Zero Delay Arcade USB Encoder & Wire Set (Not included)
Compatible like buttons


Spec Diagrams :

1Pc DIY Arcade 8 Way Joystick Replacement Parts for Fighting Game Competition

1Pc DIY Arcade 8 Way Joystick Replacement Parts for Fighting Game Competition
R239.90  Inc VAT
3V-7V DIY Light Shock Absorbed Tank Robot Chassis With 130 Motors (tank chassis shocks)
Features:

1. Only 166g in weight
2. Good damping effect, you can press down to 0.7cm
3. With general motors 130, support 3-7V voltage
4. With the DC charging port at the bottom of the tail


Specifications:

Size: wide 9.7cm* long 18.5cm* high 5cm
Voltage: 3-7V
Motors: 130
Weight: 166g

 

Package Included:

1x Tank Robot Chassis

Read the Docs
R419.90  Inc VAT
WS AlphaBot2 Acce robot DIY kit for Raspberry Pi Zero/Zero W (Alphabot2 Zero)

AlphaBot2-PiZero Acce Pack requires the controller Raspberry Pi Zero/Zero W /Zero WH if you don't have one in hand please use the links to add them to your order. Batteries are not included.

Overview

This AlphaBot2 robot kit is designed to use with Raspberry Pi Zero/Zero W (not included). It features rich common robot functions including line tracking, obstacle avoiding, ultrasonic ranging, Bluetooth/infrared/WiFi remote control (Bluetooth and WiFi are Zero W specific), video monitoring, etc.

Thanks to the highly integrated modular design, it is fairly easy to assemble by a snap, no soldering, no wiring. After a few minutes spent on hardware assembling, you're almost there, our open source demo codes is ready to help you get started fast.

AlphaBot2 Features

AlphaBot2 employs a 2-layer structure to provide excellent stability and compatibility.

AlphaBot2-Base, the lower base chassis:

  • 5-ch infrared sensor, analog output, combined with PID algorithm, stable line tracking
  • Onboard modules like line tracking, obstacle avoiding, needs no messy wiring
  • TB6612FNG dual H-bridge motor driver, compared with L298P, it's more efficient, more compact, and less heating
  • N20 micro gear motor, with metal gears, low noise, high accuracy
  • Onboard RGB LEDs, true color lighting, pretty cool

AlphaBot2-PiZero, the upper adapter board for controller:

  • LM2596 voltage regulator, provides the Pi with stable 5V power
  • TLC1543 AD acquisition chip, allows the Pi to use analog sensors
  • PCA9685 servo controller, make it more smoothly to rotate the pan head
  • CP2102 UART converter, easy for controlling the Pi via UART
  • USB HUB chip, more USB ports for devices like NIC

What's on the AlphaBot2-Base

  1. AlphaBot2 control interface: for connecting sorts of controller adapter board
  2. Ultrasonic module interface
  3. Obstacle avoiding indicators
  4. Omni-direction wheel
  5. ST188: reflective infrared photoelectric sensor, for obstacle avoiding
  6. ITR20001/T: reflective infrared photoelectric sensor, for line tracking
  7. Potentiometer for adjusting obstacle avoiding range
  8. TB6612FNG dual H-bridge motor driver
  9. LM393 voltage comparator
  10. N20 micro gear motor reduction rate 1:30, 6V/600RPM
  11. Rubber wheels diameter 42mm, width 19mm
  12. Power switch
  13. Battery holder: supports 14500 batteries
  14. WS2812B: true color RGB LEDs
  15. Power indicator

What's on the AlphaBot2-PiZero

  1. AlphaBot2 control interface: for connecting AlphaBot2-Base
  2. LM2596: 5V voltage regulator
  3. Raspberry Pi interface: for connecting Raspberry Pi Zero/Zero W
  4. IR receiver
  5. Buzzer
  6. FE1.1S: USB HUB chip
  7. 12M crystal
  8. USB TO UART: easy for controlling the Pi via UART
  9. USB HUB interface: extends the USB port of Raspberry Pi Zero/Zero W
  10. CP2102: USB TO UART converter
  11. PCA9685: servo controller, make it more smoothly to rotate the pan head
  12. TLC1543: 10-bit AD acquisition chip, allows the Pi to use analog sensors
  13. Servo interface
  14. USB indicators
  15. USB ports: more USB capability

Examples

AlphaBot2 multi robots line following

AlphaBot2-PiZero robot obstacle avoiding

AlphaBot2-PiZero robot RGB LED remote control

AlphaBot2-PiZero robot video monitor

AlphaBot2-PiZero robot Bluetooth control

Development Resources

Wiki : www.waveshare.com/wiki/AlphaBot2-PiZero

Note: this product requires two 14500 batteries to work, which are NOT included and should be purchased separately. Even though the battery holder fits the normal AA batteries DO NOT USE THEM!  A 14500 lithium cell is identical in shape and size to a standard AA battery. But that is where the similarities end. AA supplies 1.5V each where 14500 supply 3.7V each.


Package Includes:

  1. AlphaBot2-PiZero (adapter board) x1
  2. AlphaBot2-Base (base chassis) x1
  3. RPi Camera (B) x1
  4. Ultrasonic sensor
  5. Micro SD Card 16GB x1
  6. Power adapter US standard 5V/2.5A USB output x1
  7. SG90 servo x2
  8. 2 DOF pan and tilt kit x1
  9. IR remote controller x1
  10. FC-20P cable 8cm x1
  11. Micro USB connector x1
  12. RPi Zero V1.3 Camera Cable 30cm x1
  13. USB type A plug to micro B plug cable x1
  14. AlphaBot2-PiZero screws x1
  15. Micro SD Card Reader x1 
  16. Screwdriver x1 
R1,499.90  Inc VAT
MS Flux PEN for DIY Solar cell Panels and soldering projects (Misol flux pen)

Description:

  • No-Clean Flux
  • Net volume: 10ml
  • Shelf life @ 25 degree C: 2 year
  • Push the pen tip to start the flux flow
  • Keep the pen cap on when not in use

Warning:

  • When coming into contact with skin, please wash the area immediately to avoid skin irritation.
  • Do not consume.
  • Please store in a safe location where children can not reach it.


Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
R49.90  Inc VAT
DIY DC 7.4V 2 Slot 18650 Battery Holder Battery Box With 2 Leads ROHS Certification (18650 twin battery holder)
Features:

Rated voltage: DC 7.4V
Material: ABS

Product certification: ROHS
Size: 77.7mm X 40.21mm X 21.54mm

Package includes:

1 x 2 slot 18650 battery holder
R26.90  Inc VAT
Educational My First DIY Circuit Kit (My first circuit kit)
Specifications:
Color: Green
Material: Plastic
Battery: 2 X AA Battery (Not included)
Switch Size: (L)X(W) 71mm X 32mm(appr.)
Battery Holder Size: (L)X(W) 80mm X20mm(appr.)
Bulb Holder Size: (L)X(W) 71mm X32mm/(appr.)
 
Features:
 
1. Assisting teachers and parents in better physics teaching
2. Enrich children's leisure life, cultivate hands-on ability, and consolidate knowledge
3. Let kindergarten children and elementary school students learn physical knowledge by forming a simple circuit, series circuit, parallel circuit
 
Package includes:
4 X Bulbs
1 X Switch
2 X Bulb Holders
6 X Conductive Lines
2 X Battery Holders (Battery Not Included)
R159.90  Inc VAT
4 In 1 Charger Discharger Boost 5V 2.1A Module for 3.7V 4.2V Battery DIY Mobile Power with Button (charge/discharge power module)
Description
trigger: input LOW(grounding)
Single Chip Using: If Small load KEY connect 20S single chip and supply with input LOW, the module will work well.

Charge voltage: DC 4.5V-5.5V(Recommend DC 5V)    
Charging current: 0-2.1A
Charge quiescent current: 100uA
Full charge voltage: 4.2V+-1%
Discharge current: 0-2.4A
Discharge quiescent current:50uA
Discharge conversion efficiency: MAX 96%
Output voltage: 5V
Output current: 0-2.4A
Operating ambient temperature: -20°to +85°
Size: 25x16x4mm
Weight: 2.3g
PCB board design: Immersion Gold
Battery protection: OCP/OVP/SCP/OTP


About module pin
1 VIN: charge port +
2 GND: charge port -
3 BAT: Battery +
4 GND: Battery -
5 GND: output -
6 VOUT: output +
7 KEY: trigger


Note:
1.In discharging mode(charging mode KEY function invalid), trigger KEY one time,output open; trigger two times, output close.
2.Output will open automatically if you connect load. If load below 50MA, the module will turn off output port; if load over 50MA, output port will always open.
3.Allow charging and discharging at the same time(output voltage should below 5V.Stop charging and stop discharging,you should reactivation the module.)


Package Includes:
1 x power module
1 x button

---

1. Charge/Discharge: All cables
2. Charge: Connect power supply and battery
3. Discharge: Connect battery and output





R99.90  Inc VAT
2 Pcs LilyPad Button Connect Sensor Board Module for Arduino Power DIY KIT Momentary Push Button Electronic PCB Board Module (wearable buttons(2))
We designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!

Package:

2 x LilyPad Button Board module for ArduinoWe designed this board to give the user a very discrete button without any edges. Button closes when you push it and opens when you release (momentary push button).
Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!
 
Dimensions:

8mm x 16mm
Thin 0.8mm PCB
 
Package Includes:

2 x LilyPad Button Board module for Arduino

Getting started with Lilypad button sensor board
R10.90  Inc VAT
Rear Bike Light Project Kit (KT bike kit)
Product Description

This easy build bike light kit has just ten parts, making it a good introduction to electronics. The kit uses two ultra bright red LEDs, which flash rapidly, providing a highly visible light. Making it ideal for use as a rear bike light.

Alternatively it can be used as a night safety product or flashing eyes.

Features:

  • Easy build kit making a great introduction to electronics.
  • Great visibility for night time safety.

Contents:

  • 1 x 2xAA Battery Cage with Leads.
  • 2 x 470K Resistor.
  • 1 x 33R Resistor.
  • 2 x Capacitor, Electrolytic, 16V, 10uF.
  • 2 x BC547 NPN Transistor.
  • 2 x Red 5mm Water Clear LED - 30deg - 1000mCd.

Dimensions:

  • Length: 48.5mm.
  • Width: 25.5mm.

Requires:


Resources:


This easy build bike light kit has just ten parts, making it a good introduction to electronics. The kit uses two ultra bright red LEDs, which flash rapidly, providing a highly visible light. Making it ideal for use as a rear bike light.

Alternatively it can be used as a night safety product or flashing eyes.

Caution:

  • This is an educational kit and should be used in conjunction with a commercially available bike light.
R59.90  Inc VAT
Easy Build Timer Project Kit (KT timer kit)
Product Description

With its low part count this easy build timer project makes a good introduction to electronics. The timer uses a resistor capacitor network to provide a time delay of between 1 second and 4 minutes, which is set by the PCB mount variable resistor. When the button is pressed the LED changes from red to green, then at the end of the time interval it turns red.

Features:

  • Easy build timer kit.
  • When the time set has been reached the LED changes colour.
  • The time delay can be adjusted via the variable resistor.

Contents:

  • 1 x 2AA Battery Cage.
  • 1 x 47Ω Resistor.
  • 2 x 10KΩ Resistors.
  • 1 x 1MΩ Potentiometer.
  • 1 x Capacitor, Electrolytic, 10V, 1 mF.
  • 1 x BC558 PNP Transistor.
  • 1 x Tri colour 5mm diffused LED - 650mCd.
  • 1 x 6mm PCB Mount Tactile Switch 9.5mm Height.
  • 1 x Easy Build Timer PCB

Dimensions:

  • PCB Length: 54mm.
  • PCB Width: 26mm.

Requires:


Resources:

Note:

  • This kit requires soldering.
R69.90  Inc VAT
Air Freshener Kit (KT fan kit)
Product Description

This kit uses a silent low current motor to spin a fan, making it perfect to circulate air through an air freshener containing potpourri or it can be used to move a light weight buggy. The electronics take no power in standby and when the switch is pressed the motor spins for up to 100 seconds. This time is adjustable via the on board variable resistor.

Features:

  • Silent motor.
  • Adjustable timer.

Contents:

  • 1 x Battery Holder With Leads (2x AA).
  • 1 x 1K Resistor 5%.
  • 1 x 1M resistor.
  • 1 x PCB Trimmer 1M POT.
  • 1 x 16V 220uF Electrolytic Capacitor.
  • 2 x BC547 NPN Transistor.
  • 1 x Miniature Push to Make Switch, Red.
  • 1 x Low Inertia Solar Motor - 1820 RPM.
  • 1 x 55mm White Four Blade Miniature Impeller.
  • 0.5m Connecting Wire.
  • 1 x Air Freshener PCB.

Dimensions:

  • Length: 46mm.
  • Width: 28mm.

Requires:

Resources:

This kit is supplied in a grip seal bag.


R99.90  Inc VAT
Heat Activated Switch (KT heat switch kit)
Product Description

This temperature activated project kit is also available as a light activated project kit. The output of this board can be used to control other electronic circuits, turning them on automatically when it goes hot or cold.

The board has space for an LED with current limit resistor (both available separately) which will light when the output turns on.

The Darlington pair transistor configuration allows an output current of up to half an amp to be controlled. Operating voltage 3V to 10V (lower voltages allow for better adjustment of the switching point).

Features:

  • The Temperature Switch Kit detects the temperature of its surroundings using a thermistor.
  • The kit acts as an automated on/off switch (temperature dependent).

Contents:

  • 1 x 47KΩ Potentiometer.
  • 2 x BC337 NPN Transistors.
  • 1 x Thermistor.
  • 1 x 220Ω Resistor.
  • 1 x Heat Activated Switch PCB

Possible applications include:

  • Babies bath over temperature indicator.
  • Automatic fan.

Dimensions:

  • PCB Length: 53mm.
  • PCB Width: 25.5mm.

Requires:


Resources:


Note:

  • This kit requires soldering.
R53.90  Inc VAT
Steady Hand Terminal Project Kit (KT steady hand kit)

Product description:

This easy build steady hand game kit requires no soldering. Terminal blocks are used to connect the battery pack, buzzer, game loop and wire, such that when the loop touches the wire the buzzer sounds.

Features:

  • Requires no soldering.
  • Steady hand loop game.

Contents (per kit):

  • 1 x 2xAA Battery Cage with Leads.
  • 1 x 60cm length Extra Flexible Wire, Black.
  • 1 x 1m length Solid Core Cable.
  • 1 x 10cm length Black Heat Shrink, 2.4mm.
  • 4 x Terminal Block.

Requires:

  • 2 x AA Batteries.

Resources:

R64.90  Inc VAT
Relay Board (KT relay kit)
Product Description

This is a versatile relay board kit that can easily be configured via jumpers and trimmer potentiometers to do a range of tasks.

Most sensor and switches can be connected to the input of the board and the trigger level set for the input device. This can be inverted if required, then there is the option to feed this straight to the relay or a timer of up to 25 minutes can be used. Irrespective of the state of the invert jumper whenever the sense LED goes from off to on the timer restarts.#

The board can run off any voltage from 4.5 to 6 volts.

The output cans switch DC or mains.

This datasheet details what the board does and how to use it along with some worked examples. A more detailed set of information including the build instructions & how to configure the kit can also be downloaded.

Click here to download the full teaching notes pdf_icon.gif

WARNING: Using mains electricity can be dangerous and should only be attempted by qualified electricians.

This kit includes:

  • 3 x 100Kohm resistors
  • 3 x 220ohm resistors
  • 1 x 47Kohm resistors
  • 1 x 1Mohmpotentiometer
  • 1 x 10Mohm potentiometer
  • 2 x 1N4001 diodes
  • 2 x 5mm red LEDs
  • 1 x 100uF capacitors, electrolytic
  • 1 x 4.7uF capacitors, electrolytic
  • 1 x 2N7000 n-channel FET
  • 2 x 2 way terminal blocks
  • 1 x 3 way terminal blocks
  • 1 x LM324 operational amplifier IC
  • 1 x 14 pin IC holder
  • 2 x 3 way pinstrip
  • 2 x Jumpers
  • 1 x Relay
  • 1 x Relay board PCB

PCB dimensions: 86.5mm x 49mm.

This kit is supplied as a pack of parts and requires soldering.

R159.90  Inc VAT
Deluxe Rear Bike Light Kit (KT deluxe bike kit)
Product Description

The Kitronik Deluxe Rear Bike Light Kit is easy to build kit and is an excellent way to learn about the very popular 555 timer IC. The kit uses four ultra bright LEDs that can be operated in two modes; constant and flashing.

A key design aim of the kit was that it should conform to all relevant British Standard measures. Both the flash rate and brightness conform to British Standards for vehicle road lighting (2005), making it ideal for use as a rear bike light. Alternatively, it can be used as a night safety product or flashing eyes.

During testing we connected the kit to 3 x AAA batteries and ran it continuously. At 80 hours of continuous use the LEDs were still lit at full brightness. After 107 hours, although still lit, the brightness had dropped below the level at which you would want to use them. So, we estimate that with brand new batteries you could comfortably run the light for 2 hours of daily commuting for at least an entire month with the LEDs still at full brightness.

Features:

  • An easy to build rear bike light project that conforms to British Standards for vehicle road lighting (2005) for both brightness and flash rate.
  • Learn about the very popular 555 timer IC.
  • The kit features 4 x bright LEDs.
  • It has two operating modes; continuous and flashing.
  • Its compact design makes it the ideal choice for designing custom enclosures.

Contains:


Dimensions:

  • PCB Length: 52.6mm.
  • PCB Width: 37.6mm.
  • PCB Thickness: 1.6mm.

Video: https://youtu.be/KPPh7Nwa1ts

Requires:


Resources:

R104.90  Inc VAT
Ceramic Cartridge Heater 24V 40W 620 with 1M Wire for 3D Printer DIY Kit (24V heat cartridge)
Features:
Cartridge heater widely used for 3D printers.
Voltage 24V and power 40W, can provide uniform distribution of heat.
Consisting of a cylindrical stainless steel tube for corrosion prevention.
High quality wire core with fine and quick heat conductivity.
The cable is approx. 1 meter. The stainless steel part is 6mm in diameter and 20mm in length.

Specifications:
Voltage: 24V
Power: 40W
Diameter: 6mm, Length: 20mm (stainless steel part)
Wire Length: Approx. 1m

Note:
The item only includes the cartridge heater.
Heating pipe should be stored in a dry place, not damp.

Packing List:
1 x Cartridge Heater
R119.90  Inc VAT
EleksMaker Mana 3 Axis Stepper Motor Driver Board Controller For DIY Laser Engraver (Laser 3 axis driver board)
EleksMaker® Mana 3 Axis Control Board is not only for EleksMaker EleksMill Machine, but also suitable for most mini 3 axis cnc engraving machines of the market (such as 3018 / 2417 CNC Router).

Specifications:
General Specification
 Brand EleksMaker®
 Model Mana
 Product Name 3 Axis Control Board
 Product Size 90mm x 50mm x 20mm
 Board Dimension (L*W) 80mm x 77mm
 Technical Parameters
 Interface Port Micro USB
 Supply Voltage  DC12V-5A
 Operating System  Windows 7/8/10
 Software Support  EleksCAM (Recommended) / Candle / T2-Laser...
 Support Axis  3 Axis
 Support Stepper Motor  Motor within 2A  2-phase 4-wire
 Power Interface  DC5.5 - 2.1  (Inside is positive  electrodes and outside is negative electrodes)

Features:
1. Expansion of functions: stop, pause, resume, fans, low light, external relay.
2. Fit for DIY desktop laser engraver,dispensing machines printer,plotter,tool CNC.
3. Three axis linkage, Y-axis dual interface, can drive a stepper motor within 2A 2-phase 4-wire.
4. Micro USB interfaces, 12V power supply, delivery lines! Send software! Technical support!
5. Large MOS tube, onboard DC buck module, wire jump ADJ can adjust manually the laser voltage to control the laser power.
 
Tips:
- Official EleksCAM Software Download Link: http://wiki.eleksmaker.com/doku.php?id=elekscam;
- Interface Description: http://wiki.eleksmaker.com/doku.php?id=eleksmanav5.1
 
Note:
1. There isn't a  Voltage Regulator Module in this Laser board.
2. Please use EleksCAM software if you want to use this control board on 3018 router or other 3 axis cnc engraving machine.
3. The motor can not work higher than 2A, when the motor work for a long time in 1A to 2A , please pay attention to heat.
 
Package Includes:
1 x 3 Axis Driver Board
1 x USB Cable
5 x Connector Wires
R679.90  Inc VAT
Per Page      1 - 20 of 41