Search
Search Criteria
Products meeting the search criteria

Description:
You will find a South African plug adapter here
The official Raspberry Pi USB-C power supply is designed to power the latest Raspberry Pi 4 Model B computers, which were released in June 2019.
Featuring a captive USB-C cable, the power supply is available in four different models to suit different international power sockets, and in two colours, white and black.
If you need to use the power supply for an earlier model RPi or the zero you'll need a type C to micro B adapter than you will find at https://www.pishop.co.za/store/rpi-power/black-usb-type-c-female-to-micro-usb-male-adapter
Specifications
Output
- Output voltage: 5.1V DC
- Minimum load current: 0A
- Nominal load current: 3.0A
- Maximum power: 15.3W
- Load regulation: ±5%
- Line regulation: ±2%
- Ripple & noise: 120mVp-p
- Rise time: 100ms maximum to regulation limits for DC outputs
- Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
- Protection: Short circuit protection, Overcurrent protection, Over temperature protection
- Efficiency: 81% minimum (output current from 100%,75%, 50%, 25%)72% minimum at 10% load
- Output cable: 1.5m 18AWG
- Output connector: USB Type-C
Input
- Voltage range: 100-240Vac (rated)
- 96-264Vac (operating)
- Frequency: 50/60Hz ±3Hz
- Current: 0.5A maximum
- Power consumption (no load): 0.075W maximum
- Inrush current: No damage shall occur and the input fuse shall not blow
UL94V-1
AC pin material
Brass (NI plated)
WARNINGS
• This product should be operated in a well-ventilated environment.
• The connection of incompatible devices to this power supply may affect compliance, result in damage to the unit and invalidate the warranty.
What's in the box:
1 x USB-C 15.3W power supply
SAFETY INSTRUCTIONS
To avoid malfunction or damage to this product please observe the following:
• Do not expose to water or moisture, or place on a conductive surface whilst in operation.
• Do not expose to heat from any source; this is designed for reliable operation at normal ambient room temperatures.
• Do not attempt to open or remove the power supply case.
UNO R3 is a microcontroller board based on the ATmega328P.
The Arduino Uno R3 comes in two models; the normal version and the SMD version. In the SMD version you have the Atmega328 controller IC as an SMD chip soldered into the board, whereas in the normal version the IC is held on the Arduino by an IC Holder.
It has:
- 14 digital input/output pins (of which 6 can be used as PWM outputs)
- 6 analog inputs
- a 16 MHz quartz crystal
- a USB connection
- a power jack
- an ICSP header
- a reset button.
It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
Package Includes:
1 x Arduino Uno SMD
1 x Headers
1 x USB cable
Resources:
Getting started with Arduino products
The USB to Micro USB Cable is 1m long manufactured by Raspberry Pi. This cable can be used in conjunction with a USB mains charger or Computer USB port to power your Raspberry Pi.
Specifications:- 1m Long
- Colour: Red
- Connector Type A: USB
- Connector Type B: Micro USB
- 1 x USB A male to USB micro B male 1m

Description:
You will find a South African plug adapter here
The official Raspberry Pi USB-C power supply is designed to power the latest Raspberry Pi 4 Model B computers, which were released in June 2019.
Featuring a captive USB-C cable, the power supply is available in four different models to suit different international power sockets, and in two colours, white and black.
If you need to use the power supply for an earlier model RPi or the zero you'll need a type C to micro B adapter than you will find at https://www.pishop.co.za/store/rpi-power/usb-type-c-female-to-micro-usb-male-adapter
Specifications
Output
- Output voltage: 5.1V DC
- Minimum load current: 0A
- Nominal load current: 3.0A
- Maximum power: 15.3W
- Load regulation: ±5%
- Line regulation: ±2%
- Ripple & noise: 120mVp-p
- Rise time: 100ms maximum to regulation limits for DC outputs
- Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
- Protection: Short circuit protection, Overcurrent protection, Over temperature protection
- Efficiency: 81% minimum (output current from 100%,75%, 50%, 25%)72% minimum at 10% load
- Output cable: 1.5m 18AWG
- Output connector: USB Type-C
Input
- Voltage range: 100-240Vac (rated)
- 96-264Vac (operating)
- Frequency: 50/60Hz ±3Hz
- Current: 0.5A maximum
- Power consumption (no load): 0.075W maximum
- Inrush current: No damage shall occur and the input fuse shall not blow
UL94V-1
AC pin material
Brass (NI plated)
What's in the box:
1 x USB-C 15.3W power supply
WARNINGS
• This product should be operated in a well-ventilated environment.
• The connection of incompatible devices to this power supply may affect compliance, result in damage to the unit and invalidate the warranty.
SAFETY INSTRUCTIONS
To avoid malfunction or damage to this product please observe the following:
• Do not expose to water or moisture, or place on a conductive surface whilst in operation.
• Do not expose to heat from any source; this is designed for reliable operation at normal ambient room temperatures.
• Do not attempt to open or remove the power supply case.
Description:
You will find a South African plug adapter here
This PSU supports up to 2.5A of current, so it won't let you down when powering hungry devices through your Raspberry Pi 3 Model B, Zero and Pico
Specifications:
Output
- Output voltage: 5.1V DC
- Minimum load current: 0.0A
- Nominal load current: 2.5A
- Maximum power: 12.5W
- Load regulation: ±5%
- Line regulation: ±2%
- Ripple & noise: 120mVp-p
- Rise time: 100ms maximum to regulation limits for DC outputs
- Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
- Protection: Short circuit protection
Overcurrent protection
- Efficiency: 80.73% minimum (output current from 100%, 75%, 50%, 25%)
- Output cable: 1.5m 18AWG
- Output connector: mirco USB
Input
- Voltage range: 100–240Vac (rated) 96–264Vac (operating)
- Frequency: 50/60Hz ±3Hz
- Current: 0.5A maximum
- Power consumption (no load): 0.075W maximum
- Inrush current: No damage shall occur and the input fuse shall not blow
What's in the box?
1 x Official Power Supply
WARNINGS
• This product should be operated in a well-ventilated environment.
• The connection of incompatible devices to this power supply may affect compliance, result in damage to the unit and invalidate the warranty.
SAFETY INSTRUCTIONS
To avoid malfunction or damage to this product please observe the following:
• Do not expose to water or moisture, or place on a conductive surface whilst in operation.
• Do not expose to heat from any source; this is designed for reliable operation at normal ambient room temperatures.
• Do not attempt to open or remove the power supply case.
This adapter kit was created for the Raspberry Pi Zero. It includes all the adapters you need to get your Raspberry pi Zero going.
What's in the box?
1 x pin header 2x20
1 x Official Raspberry Pi male mini HDMI to female HDMI adapter
1 x Official Raspberry Pi OTG male micro USB to female USB A adapter
The Official Raspberry Pi Mouse is finally here!
This sleek, stylish and ergonomic mouse from the team at Raspberry Pi includes three buttons, two main ones for right and left click, and a scroll wheel with button for scrolling. . . and more clicking. . . what more do you need from a mouse!
Mouse Specification:
- Three-button optical mouse
- Scroll wheel
- USB type-A connector
- Compatible with all Raspberry Pi products
- Ergonomic design for comfortable use
- Available in Black/Grey and Red/White
Description:
The Official Raspberry Pi Mouse is finally here!
This sleek, stylish and ergonomic mouse from the team at Raspberry Pi includes three buttons, two main ones for right and left click, and a scroll wheel with button for scrolling. . . and more clicking. . . what more do you need from a mouse!
Mouse Specification:
- Three-button optical mouse
- Scroll wheel
- USB type-A connector
- Compatible with all Raspberry Pi products
- Ergonomic design for comfortable use
- Available in Red/White and Black/Grey
- This mouse will look great with your Red/White official keyboard
What's in the box?:
1 x USB Mouse
Arduino compatible R3 Mega2560 ATmega2560-16AU control board with USB cable
Arduino Mega is an ATmega2560 core microcontroller development board. Itself has 54 digital input/output terminals (14 PWM outputs), 16 simulation inputs, 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writers. Supply part of the optional USB power, or external power using a AC-to-DC adapter and battery.
Rapid growth due to open original code, as well as the concept of using Java (cross-platform) C language development environment for Arduino module. The Arduino can easily use the Arduino language with Flash or Processing ... software communication, to make multimedia interactive works. Arduino development IDE interface is based on open-source principles, allows you to download for use in projects.
Power supply design:
There are two options for the power supply system of the Arduino Mega. USB direct power supply or external power supply. The power supply will be switched automatically. External supply AC-to-DC adapter or the battery can be selected on this control panel. Limit the voltage range of 6V ~~ 12V, but if the voltage supplied is less than 6V, I / O port may not be supplied to a voltage of 5V, and therefore not stable; If the voltage is greater than 12V, the regulator device may possibly overheat and damage the Arduino MEGA. It is therefore recommended that for the operating supply of 6.5 ~ 12V, the recommended power supply is 7.5V or 9V.
The development board have been rigorously tested at the factory.
Specification:
Microcontroller: ATmega2560
Operating voltage: 5V
Input voltage (recommended): 7-12V
Digital I/O pins: 54 (of which 14 provide PWM output)
Analog input pins: 16
DC current per I/O pin: 40 mA
DC current for 3.3V Pin: 50 mA
Flash Memory: 256 KB of which 4 KB is used by the bootloader
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16MHz
Getting started with Arduino products
Package includes:
1 x Control board
1 x USB cable
The USB to Micro USB Cable is 1.5m long and has been tested for compatibility with the Raspberry Pi. This cable can be used in conjunction with a USB mains charger or Computer USB port to power your Raspberry Pi.
Specifications:- Tested for Compatibility with the Raspberry Pi
- 26AWG (Up to 2A)
- 1.5m Long
- Colour: Black
- Connector Type A: USB
- Connector Type B: Micro USB
- 1 x USB A male to USB micro B male 1.5m
You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It flips between voltage and current readouts every 3 seconds or so. It's a very handy tool for testing USB devices, checking load levels and debugging battery chargers and boost converters.
Specifications:- USB 1.x and 2.x - all data speeds. Does not have USB v3 pins so USB v3 connections will automatically downgrade to v2
- Working Range: 0~3A, 3.5~7VDC
- Resolution: 10mV / 10mA
- Operating Temperature: 0-60ºC
- Contents:
- Camera Board 360 Gooseneck Mount V2
Dimensions:
- 21mm x 53mm x 15mm / 0.8" x 2.1" x 0.6"
- USB Plug: 13mm / 0.5"
- Weight: 16.2g
1 x USB Voltage and Current Meter
MODULAR CASE NOT INCLUDED
The Modular Raspberry Pi Case is designed to be fully customisable by the user, and adaptable to suit a range of requirements. The streamlined look, and adaptability makes it perfect for many applications, including: the hobbyist maker, digital signage, industrial protection, living-room & child-friendly media centres, classroom eduction, workshops and many more! All add-ons are designed to be interchangeable and can be added and removed when required.
The USB/HDMI security cover is a dual-use shroud that can be utilised to protect access to all the external inputs and outputs. Two covers can be used simultaneously if only very limited access is required, and “punch-out” access hatches are available for both the Ethernet and Micro USB power port if these inputs are required. Security covers are tamperproof and can only be removed from inside the case.
In addition to protecting the Raspberry Pi ports, the shroud is offset from the body by 12mm. The enables the secure, internal and protected use of up to four nano USB dongles with the cover installed.
Specifications:- Dual-Use - Compatible with Either Set of I/O Ports e.g. HDMI or USB Side
- Secure and Tamper-Proof
- RJ45 & Micro USB Power Breakout Hatches
- Off-Set to Enable the Use & Internal Protection of up to 4 Nano USB Dongles!
- 1 x USB/HDMI Cover
The staple of any USB connection, the USB A to B cable connects any standard host device (computer, hub, or controller) to any standard peripheral (printer, scanner, external drive).
Specification:
1. USB 2.0 specification
2. Connector: USB 2.0-A male > USB 2.0-B male
3. Cable length: 1.8m
4. For use with Arduino
What's in the box?
1 x USB A to B cable
Need a high quality SD & Micro SD card reader/writer that can handle SD card sizes up to 512GB? We've found one! The Kawau C296 2 in 1 USB card reader features two slots, one for a standard size SD card, and one for Micro SD cards. It uses USB 2.0, with transfer speeds up to 480Mbps, and it's plug and play! A lot of cheaper SD card readers will not read cards above 32GB (or even 16GB on some of the really cheap ones), but never fear! You can now future proof your SD card library, safe in the knowledge that your Kawau SD card reader can take cards up to 512GB's!
Supports SD, SDHC, SDXC, MMC, Exteme SD, Mini SD, Micro SD, Micro SDXC, Micro SDHC Memory Cards, in addition to the latest format UHS cards.
Technical Details
- Brand: Kawau
- Model: C296
- Compatible Cards:
- SD
- SDHC
- SDXC
- MMC
- Extreme SD
- Mini SD
- Micro SD
- Micro SDXC
- Micro SDHC
- UHS
- Supports Card Sizes:
- 4GB
- 8GB
- 16GB
- 32GB
- 64GB
- 128GB
- 256GB
- 512GB
- Colour: Black
- Blue Transfer Light
- Supports up to 512GB
- Size: 60 x 17 x 8.5 mm
- Weight: 16.05 g
1 x USB SD & Micro SD Card Reader
The Modular Raspberry Pi Case is designed to be fully customisable by the user, and adaptable to suit a range of requirements. The streamlined look, and adaptability makes it perfect for many applications, including: the hobbyist maker, digital signage, industrial protection, living-room & child-friendly media centres, classroom eduction, workshops and many more! All add-ons are designed to be interchangeable and can be added and removed when required.
- Dual-Use - Compatible with Either Set of I/O Ports e.g. HDMI or USB Side
- Secure and Tamper-Proof
- RJ45 & Micro USB Power Breakout Hatches
- Off-Set to Enable the Use & Internal Protection of up to 4 Nano USB Dongles!
Use the USB Charger Doctor to measure the working voltage and current output for any USB port and project. This plastic dongle plugs between a USB device, and passes the data lines through. There's a 0.05 ohm resistor in line with the power pin that is used to measure current draw. The Doctor's digital display instantly reads the numbers out for testing devices such as chargers, cables, and cell phones.
You can use this device from 3.5-7VDC input voltage (although most USB devices tend to hover around 4.75 to 5.25) and up to 3A of current. It displays both voltage and current readouts. It's a very handy tool for testing USB devices, checking load levels and debugging battery chargers and boost converters.
Specifications:
Voltage range: 3.3V-9V
Current range: 0-3A
Voltage display: red
Current display: blue
Out put : 2 USB
Size: 52mm x 34mm x12mm
Weight: 16g
Shell color: Dark black
What's in the box?:
1 x Voltage Tester Dual USB
Description:
The FLIRC USB dongle allows the use of any remote control with your Raspberry Pi. Configure the device on your desktop PC, then simply plug into your Pi for a perfect media centre companion! Amaze your friends and family when the tiny box stuck to the back of your TV controls your entire media collection using an old DVD remote!
New Flirc Version 2 is smaller, lighter and much more professional!
- Setting up OSMC (XBMC) media operating system on the Raspberry Pi.
- Setting up your FLIRC module and porting it to any remote.
- Putting it all together!
- More advanced FLIRC programming - porting an entire keyboard to a remote!
Each encoder can support one joystick. Use them to DIY your own Arcade game machine. The Zero Delay USB Arcade Encoder is a fully compatible plug and play solution, simply plug in your joystick and buttons into the encoder, plug the USB cable into the Pi, map your buttons in RetroPi and away you go - it really is that easy! You can use multiple encoders at the same time, so they're great for multiplayer arcade machines!
Joystick Size: Approx. 95x60x100mm
Encoder Board Size: Approx. 85x35mm
USB Cable Length: Approx. 1.8m
Colour: Red
We have tested this unit on Raspberry Pi using Retropie and a Windows 7 PC using MAME.
Each encoder can support one joystick. Use them to DIY your own Arcade game machine. The Zero Delay USB Arcade Encoder is a fully compatible plug and play solution, simply plug in your joystick and buttons into the encoder, plug the USB cable into the Pi, map your buttons in RetroPi and away you go - it really is that easy! You can use multiple encoders at the same time, so they're great for multiplayer arcade machines!
Joystick Size: Approx. 95x60x100mm
Encoder Board Size: Approx. 85x35mm
USB Cable Length: Approx. 1.8m
Colour: Blue
We have tested this unit on Raspberry Pi using Retropie and a Windows 7 PC using MAME.
Description:
This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. It's short (30cm between connectors), so perfect for mounting your Raspberry Pi, Beagle Bone, Arduino etc. into a box!
The jack half has two mounting 'ears' with M3 screws installed, 8mm apart. The ears are flexible so the holes don't have to drilled very precisely.
Our Panel Mount USB Cable Features:
- Specially Manufactured for ModMyPi for use with the Raspberry Pi & Other Microcontrollers
- Length between connectors: 30cm
- Colour: Black
- 28AWG
- USB A Male to Panel Mount USB A Female
- M3 Mounting Ears
1 x USB A Male to Panel Mount USB A Female