Search
Search Criteria
Products meeting the search criteria
Highlights:
- Mutual conversion between 3V and 5V, It's convenient for PI connected to external 5V sensors or modules
- Supports total of 8 channels
- Range of voltage converted: 1.8V~6VDC
How to Use:
In the case of translating between 3.3V and 5V system:
VCCA connects to 3.3V power supply
VCCB connects to 5V power supply
GND connects to power negative pole respectively, the two power supply should be common-grounded with each other
When Ax has 3.3V input, Bx will get 5V output
When Bx has 5V input, Ax will get 3.3V output
NO direction control required
Input voltage range: 4-40 v (40 v highest voltage limit)
Output voltage range:1.25V - 37V (input voltage must 2 V above output)
Output current: 2 A continuous output
Output power: maximum 15 w
Ripple frequency: 150 KHZ
Grain wave peak: 100 mv
IN + : input positive
IN - : input negative
OUT + : output positive
OUT - : output negative
Voltmeter precision: ± 5 ‰
Weight: 33g
Size: 7cm x 4cm
Package includes:
LM2596 voltage regulator converter module
Specification:
Built-in TTL COM PC-PL2303HX Chip
Standard USB type A male and TTL 4 pin connector
Cable length: 1000mm (39 3/8 in)
Simple and Easy way to give USB support to your projects
Black cable-----GND
Green cable----TXD
White cable----RXD
Red cable ---- VCC (5V)
Package includes:
1 x USB to RS232/TTL PL2303HX cable adapter module
If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time.
This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side.
The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV’ pin, low voltage (3.3V for example) to ‘LV’, and ground from the system to the ‘GND’ pin.
Dimensions: 0.63 x 0.52" (16.05 x 13.33mm)
Documents:
Specifications:
Input: 9V-36V
Output: 5V / 3A (MAX)
Efficiency: 92% (MAX)
Switching frequency: 150KHZ
Operating temperature: -40 ℃ - + 85 ℃
Load capacity: Maximum output 3A in total on both ports
Application: mobile power, mobile phones, flat-panel USB5V powered devices
Package includes:
1 x DC Power Module
1.Model:usb1002
2.Name: Power Module
3.Features: Buck Charge
4.Product size: 33mm x 33mm x 8mm
5.Input voltage range: 6-24V
6.Output voltage: 5.2V (the output terminal is 5.3-5.4V, the load side is 5.1-5.2V)
7.Output Current: 3A (without heat sink, the stability of the output current is 2A)
Note:
1. Input voltage can not exceed 24V, otherwise, it will cause damage to the device!
2. The input positive and negative can not be reversed, otherwise it will cause damage to the device!
Package Includes:
1 x Dual USB Power Module
Features
- 8 channels bidirectional voltage translation between different logic level, translate between Ax and Bx automatically
- 4 pairs of power supply interfaces, supports more situations
- Use tantalum capacitors for power filter, provides more stability
- Voltage level: 1.8V-6V
- Dimension: 31.6mm x 25.4mm
How to Use
In the case of translating between 3.3V and 5V system:
- VCCA/VA connects to 3.3V power supply
- VCCB/VB connects to 5V power supply
- GND connects to power negative pole respectively, the two power supply should be common-grounded with each other
- When Ax has TTL 3.3V input, Bx will get TTL 5V output
- When Bx has TTL 5V input, Ax will get TTL 3.3V output
- NO direction control required
Development Resources
Features:
Chip: FT232RL
Draw out all signal port of FT232RL chip
RXD / TXD transceiver communication indicator
USB power supply, can choose 5V or 3.3V, set by jumper
With over current protection, using 500mA self-restore fuse
Pin definition: DTR, RXD, TX, VCC, CTS, GND
Pitch: 2.54mm
Size: 36 x 18mm (L x W)
Interface: Mini USB
The USB to TTL serial adapter is based on the high quality and very popular FTDI FT232RL chipset and is an excellent way to connect TTL serial devices to a PC through a USB port.
This USB to TTL serial adapter is ideal for many uses, including:
Programming microprocessors such as ARM, AVR, etc
Working with computing hardware such as routers and switches
Serial communication with many devices such as GPS devices
Serial terminals on devices like the Raspberry Pi
Unlike most USB to TTL serial adapters, this adapter supports both 5V AND 3.3V operation! Simply set the jumper as required to choose between 5V and 3.3V as labelled on the board.
The adapter comes with a right-angle connector fitted allowing you to use it straight away. If you need to access any of the other inputs or outputs of the FT232RL, all the useful signals are provided as through-hole solder pads - ideal for use with straight headers into a breadboard, for example.
Package includes:
1 x FT232RL USB to serial converter module
2. Short circuit protection
3. Quantity: 1 pc
Minimum pressure | 2V |
Input Voltage | DC 24V(DC15V—40V) |
Output Voltage | DC 12V |
Output Power | 60W |
Output Current | 5A |
Conversion Efficiency | 90% |
Full Load Temperature Rise | 50 degree |
This power supply is a isolated industrial grade built-in power module with temperature, over current, and short circuit protection.
Features:
AC85 - 264V or DC110 - 370V wide voltage input
DC 5V(+/ -0.2V) 600mA isolated output
Input Current: 0.0273A/115VAC 0.014A/230VAC
Input surge current: 20A (230VAC)
Frequency range: 50/60 Hz
Operating Temperature: -30 - 70 ℃
Relative humidity: 20%- 90%
Rated power: 3W
Output efficiency: 80%
Module size: 40mm x 23mm x 23mm
Package includes:
1 x AC-DC Isolated AC 110V / 220V To DC 5V 600mA Constant Voltage Switch Power Supply Converter
A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your LilyPad circuit. Good up to 200mA. Short circuit protected.
This board has AAA battery clips but can use an input from 1.2V to 5V.
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable - but be sure to remove the battery!
Package Includes
1 x LilyPad Power Supply Converter Module AAA Battery Step up to 5V
Input: HDMI Micro male
Output: VGA
Cable length: 20CM
Colour: Black
Specifications:
1. Brand: Orico
2. Model: 20UTS
3. Item: HDD SSD Hard Drive Adapter Cable
4. Material: ABS
5. Interface: USB 3.0 USB-A to Micro B
6. Compatible HDD: 2.5 inch HDD / SSD
7. Controller: JMS578
8. Capacity: Support 2TB
9. Dimensions: 51mm x 30mm x 12mm
10. Supported System: Windows XP / 7 / 8 / 10, Linux, for Mac OS 9.1 and Raspberry Pi 4
11. Safety Approval: CE / FCC / RoHS

Features:
1. Helps to renew your unused hard drive, compatible with 2.5inch SATA hard drive.
2. Open thermal design makes better heat dissipation than hard drive enclosure.
3. Compared with other 5Gbps adapter, 20UTS supports UASP, which means that it can provide 6Gbps transmission rate, more efficient in data transmission.
4. Supports OTG function, for phone and tablet which supports OTG function to connect with hard drive with this adapter.
Package Includes:
1 x Orico 20UTS USB 3.0 SATA Ⅲ 6Gbps UASP 2.5inch HDD SSD External Hard Drive Adapter Converter Cable
This adapter is ideal to convert the 3A type C official power supply to micro B for the Raspberry Pi models Zero, 2 and 3.
Specifications:
Material: Plastic and Metal
Color: Available in Black and White
Length: 2.3cm
Connector A: Micro USB Male
Connector B: Type C Female
Package includes:
1 X White Type C Female To Micro USB Male Adapter
This adapter is ideal to convert the 3A type C official power supply to micro B for the Raspberry Pi models Zero, 2 and 3.
Specifications:
Material: Plastic and Metal
Color: Available in Black and White
Length: 2.3cm
Connector A: Micro USB Male
Connector B: Type C Female
Package includes:
1 X Black Type C Female To Micro USB Male Adapter
Features
- Onboard switched-capacitor successive-approximation analog-to-digital converter TLC1543
- resolution : 10Bit
- analog input : 11ch (AIN0 ~ AIN10)
- Samples Per Second (SPS) : 38K
- Serial port
- Reference voltage pins (REF+, REF-) allow user to select a proper reference voltage
- Only 3 IOs are required to use this module, suit for systems that don't have sufficient IOs but need multi analog inputs ADC
- Operating voltage : 3.3V - 5.0V
- Dimension : 43mm × 23mm
Downloads
Development resources: demo codes, schematic, datasheets, etc.
Wiki: www.waveshare.com/wiki/TLC1543_ADC_Board
Max input current: 2A
Max Output current: 750mA
(500mA or less application is recommended)
Package Includes:
1 x USB Power Cable Module Converter 2.1mm x 5.5mm Male Connector
UBEC's (Universal Battery Eliminator Circuit's) are simply DC to DC step down voltage regulators! This UBEC is perfect for the Raspberry Pi, as it's able to take high voltages (5.5V up to 26V), and outputs a consistent safe voltage of 5V at up to 3A nominal or 5A max! The Hobbywing 5V 3A UBEC is a switch-mode type, which results in it being much more efficient than linear type UBEC's (so your batteries will last longer!)
UBEC's are perfect for applications where you plan to use the Raspberry Pi in a circuit with high voltages such as robots where you'll be driving motors!
Due to the voltage drop caused by the Raspberry Pi, it is recommended to input a minimum of 6.5V to receive a stable 5V output. Anything lower than 6.5V will result in a low voltage warning on the Pi.
Please Note. The Hobbywing UBEC can be set to output either 5V or 6V using an onboard jumper select! Please DOUBLE CHECK your output voltage is correct before connecting your microcontroller or circuit!
Features
- Designed with an advanced switch mode DC-DC regulator IC.
- Battery polarity reversal protection.
- A metal shield covers almost all the electronic components, and a specially made filter is attached to the output wires to significantly reduce the electromagnetic interference.
- The working status is shown by an indicator (LED), which lights when the output is in normal range.
- Output Voltage: [email protected] or [email protected] (Changeable with an output-voltage select jumper)
- Continuous output current: 3 Amps
- Maximum output current: 5 Amps
- Input: 5.5V - 26V (2 - 6 cells lithium battery pack or 5 - 18 cells NiMH /NiCd battery)
- Size: 43mm*17mm*7mm (L*W*H)
- Weight: 11g
Check out our tutorial here: https://www.modmypi.com/blog/using-a-ubec-with-a-raspberry-pi
Data passedI2CCompatible serial interface for transmission, owned4roadI2CAddress can be selected, work power only need3.3VYou can. Its main function is that it can be used to detect analog signals and convert them to digital signals.
You can put analog signals on joysticks or other analog sensors such asNTC, Temperature, dust sensors and other equipment through thisRPi-ADS1115-ADCModule access raspberry faction, through the raspberry dispatch device to collect the analog signal.
parameter | value |
size | 65.0 mm 30.0 mm 18.0 mm |
power supply | 3.3V |
Analog input voltage | VDD,GND |
Programmable data rate | 8spsTo860sps |
internalPGA | stand by |
Sampling accuracy | 16Bit |
I2cinterface | Select the address by pin |
Number of channels | 4Single-ended or2Differential input |
Programmable Comparator(PGA) | 2/3 ~ 16 |
internalNTC | stand by |