Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
R319.90  Inc VAT
Eight super-bright RGB LED indicators that are ideal for adding visual notifications to your Raspberry Pi without breaking the bank!
R119.90  Inc VAT
R499.90  Inc VAT
R229.90  Inc VAT
ReSpeaker 4-Mic Array for Raspberry Pi is a quad-microphone expansion board for Raspberry Pi designed for AI and voice applications. This means that you can build a more powerful and flexible voice product that integrates Amazon Alexa Voice Service, Google Assistant, and so on.
R499.90  Inc VAT
This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R189.90  Inc VAT
This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R241.10  Inc VAT
This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.
R599.90  Inc VAT
Take control of and monitor your world with our ultimate jack-of-all-trades Raspberry Pi HAT!
R639.90  Inc VAT
R219.90  Inc VAT
Raspberry Pi Power over Ethernet Plus (POE+) HAT (RPi POE+ HAT)
Overview

The Raspberry Pi PoE+ HAT is an add-on board for Raspberry Pi computers with
PoE pins, including Raspberry Pi 3B+ and Raspberry Pi 4. It is used to power
Raspberry Pi via an Ethernet cable, provided that power-sourcing equipment is
installed on the Ethernet network. The HAT also includes a fan that will cool the
Raspberry Pi processor.

Specifications

Standard: IEEE 802.3at-2003 PoE
Input voltage: 37–57 V DC, Class 4 device
Output power: 5 V DC/4 A
Cooling: 25 mm × 25 mm brushless fan delivering 2.2 CFM for processor cooling

Features:
  • Fully isolated switched-mode power supply
  • Fan control

Operating temperature: 0 °C to +50 °C
Production lifetime: The Raspberry Pi PoE+ HAT will remain in production until at least January 2027
Compliance: For a full list of local and regional product approvals, please visit www.raspberrypi.org/compliance

Physical specifications


WARNINGS

• This product shall only be connected to a Raspberry Pi via the four PoE pins.
• Any external power-sourcing equipment/power injector used to enable an Ethernet network shall comply with relevant regulations and standards applicable in the country of intended use.
• This product should be operated in a well ventilated environment, and if used inside a case, the case should not be covered.
• The connection of incompatible devices to the GPIO connection of a Raspberry Pi computer may affect compliance and result in damage to the unit and invalidate the warranty.
• All peripherals used with this product should comply with relevant standards for the country of
use and be marked accordingly to ensure that safety and performance requirements are met.
These articles include but are not limited to keyboards, monitors and mice when used in conjunction with Raspberry Pi computers.
• Where peripherals are connected that do not include the cable or connector, the cable or connector must offer adequate insulation and operation in order that the relevant performance and safety requirements are met.


SAFETY INSTRUCTIONS

To avoid malfunction or damage to this product, please observe the following:
• Do not expose to water or moisture, or place on a conductive surface whilst in operation.
• Do not expose to heat from any source. Raspberry Pi computers and the Raspberry Pi PoE+ HAT are designed for reliable operation at normal ambient room temperatures.
• Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board
and connectors.
• Avoid handling the printed circuit board whilst it is powered, and handle it only by the edges to minimise the risk of electrostatic discharge damage.
R409.90  Inc VAT
Raspberry Pi 48W (8V DC, 6A) power supply for Build HAT (RPi build power supply 8V)
Description:

Official 48W (8V DC, 6A) power supply, designed for use with the Raspberry Pi Build HAT. Shipped with easily interchangeable heads for the UK, US, EU and Australia you can now use your Pi in all four corners of the world! 

Power your Raspberry Pi Build HAT projects with the Raspberry Pi Build HAT Power Supply. This 48W power supply will power the Build HAT and connected LEGO® Technic™ motors, as well as your Raspberry Pi computer.
Compatible with LEGO Technic motors and sensors included in the LEGO® Education SPIKE™ Portfolio, the Build HAT combines the power of Raspberry Pi computing with easy building opportunities to help you make creative and robust projects.

Specifications:

Output
  • Output voltage: +8.0V DC
  • Minimum load current: 0.01A
  • Nominal load current: 6.0A
  • Maximum power: 48.0W
  • Load regulation: ±5%
  • Line regulation: ±5%
  • Ripple & noise: 200mVp-p
  • Rise time: 100ms maximum to regulation limits for DC outputs
  • Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
  • Protection: Short circuit protection
  • Overcurrent protection
  • Overvoltage protection
  • Efficiency: 87.77% minimum (output current from 100%, 75%, 50%, 25%)
  • Output cable: 1.5m 16AWG
  • Output connector: Barrel connector 5.5mm × 2.1mm × 11mm Centre positive

Input
  • Voltage range: 100-240Vac (rated)
  • 96-264Vac (operating)
  • Frequency: 50/60Hz ±3Hz
  • Current: 1.2A maximum
  • Power consumption (no load): 0.1W maximum
  • Inrush current: No damage shall occur and the input fuse shall not blow

What's in the box?

1 x Official 48W power supply for Build HAT
R269.90  Inc VAT
Raspberry Pi Build HAT for LEGO (RPi build hat)
Read more in HackSpace magazine issue 49 at https://hackspace.raspberrypi.com/issues/49

Description:


The Raspberry Pi Build HAT combines the power of Raspberry Pi computing with LEGO® hands-on learning to enable a fun and creative learning experience for students, teachers and makers.

The Build HAT is compatible with the most recent generation of LEGO® Technic™ motors, and with sensors included in the LEGO® Education SPIKE™ Prime portfolio.

The Build HAT is the second Raspberry Pi product, after Raspberry Pi Pico, to be powered by the Raspberry Pi RP2040 microcontroller.



Specifications:

• Controls up to 4 motors and sensors.
• Powers the Raspberry Pi (when used with a suitable external PSU).
• Easy to use from Python on the Raspberry Pi.


What's in the box?

1 x Raspberry Pi Build HAT for LEGO

Build HAT Links


LEGO Links

R469.90  Inc VAT
Pimoroni Explorer HAT PRO (Explorer hat pro)

Please note: Raspberry Pi not included

The Explorer HAT and Explorer HAT Pro are the perfect prototyping side-kicks for your Raspberry Pi!

We've added a heap of useful input and output options that will take your projects to the next level. Great for driving motors, using analog sensors, interfacing with 5V systems, and touch (even fruit based!) interfaces.

It's compatible with Raspberry Pi 2, Pi 3, B+, and A+ and comes fully assembled.

Features:

  • Four buffered 5V tolerant inputs
  • Four powered 5V outputs (up to 500mA!)
  • Four capacitive touch pads
  • Four capacitive crocodile clip pads
  • Four coloured LEDs
  • PRO ONLY Four analog inputs
  • PRO ONLY Two H-bridge motor drivers
  • PRO ONLY A heap of useful (unprotected) 3v3 goodies from the GPIO
  • A mini breadboard on top!

5V tolerant inputs - Hook up your Pi to accept input from 5V systems (like Arduino Uno/Leonardo or 5V Trinkets). We've used a 5-channel buffer that will accept anything from 2V-5V as logic high.

5V powered ouputs - The onboard darlington array can supply up to 500mA per channel (but you'll be limited to driving around 1A total from the board). Ideal for stepper motors, solenoids, and relays.

Eight capacitive inputs - Four along the front edge for touch input (labelled 1, 2, 3, 4) and four up the side for attaching crocodile clips to objects (such as fruit, or tin foil) for experimentation!

Four coloured LEDs - Independently controllable LEDs (red, green, blue, and yellow) that make great status indicators.

Four analog inputs (pro only) - A tidy way to integrate analog signals into your project.

Two H-Bridge motor drivers (pro only) - Drive two 5V motors bidirectionally with up to 200mA per channel. Ideal with our micro-metal gear-motors to create the perfect little buggy! You can even soft-PWM for full speed control.

Full Python library, documentation and examples - Head on over to our GitHub to find a Python library, examples, documentation and a brief introduction to Explorer HAT: https://github.com/pimoroni/explorer-hat

R319.90  Inc VAT
Blinkt! (Blinkt)

Eight super-bright RGB LED indicators that are ideal for adding visual notifications to your Raspberry Pi without breaking the bank!

Inspired by Alex Ellis' work with his Raspberry Pi Zero Docker Cluster, we developed these boards for him to use as status indicators. Blinkt! offers eight APA102 pixels in the smallest (and cheapest) form factor to plug straight onto your Raspberry Pi.

Each pixel on Blinkt! is individually controllable and dimmable allowing you to create gradients, pulsing effects, or just flash them on and off like crazy. The data and clock lines are connected to GPIO #23 and #24 respectively but for simplicity you can just use our Python library to drive them.

Features

  • Eight APA102 RGB LEDs
  • Individually controllable pixels
  • Sits directly on top of your Pi in a tiny footprint
  • Fits inside most Pi cases
  • Doesn't interfere with PWM audio
  • Blinkt! pinout
  • Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Comes fully assembled

Software

Our Blinkt! Python library will have you blasting out rainbows in two shakes of a unicorn's tail! There's a stack of examples too, from binary clocks to cheerlights and flickering candles to Larson scanners!

Notes

  • Be careful to plug in your Blinkt! the correct way round, it has curves on the top that match the corners of your Raspberry Pi.
  • The dimensions of Blinkt! are 65mm long x 8mm wide x 8.5mm thick (thickness includes header and pixels).

We featured Blinkt! on a special episode of Bilge Tank where we tried to come up with as many different code examples as possible in one morning. Check it out below.



Tutorials & Projects

Eight super-bright RGB LED indicators that are ideal for adding visual notifications to your Raspberry Pi without breaking the bank!
R119.90  Inc VAT
Adafruit DC & Stepper Motor HAT - Mini Kit (Adafr DC and Step Mini Kit)

Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control.

Raspberry Pi and motors are not included.

Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or HATs to the same pins.

In fact, you can even stack multiple Motor HATs, up to 32 of them, for controlling up to 64 stepper motors or 128 DC motors (or a mix of the two) - just remember to purchase and solder in a stacking header instead of the one we include.

Motors are controlled by TB6612 MOSFET drivers with 1.2A per channel and 3A peak current capabilitya big improvement over L293D drivers and there are built-in flyback diodes as well.

We even had a little space so we added a polarity protection FET on the power pins and a bit of prototyping area. And the HAT is assembled and tested here at Adafruit so all you have to do is solder on the included 2x20 plain header and the terminal blocks.

Lets check out these specs again:

  • 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.
  • Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.
  • Big terminal block connectors to easily hook up wires (18-26AWG) and power
  • Polarity protected 2-pin terminal block and jumper to connect external 5-12VDC power
  • Works best with Raspberry Pi model A+, B+, Pi 2 B or Pi 3 B.
  • Install the easy-to-use Python library, check out the examples and you're ready to go!

Comes with an assembled & tested HAT, terminal blocks, and 2x20 plain header. Some soldering is required to assemble the headers on. Stacking header not included.

Raspberry Pi, motors, and battery pack are not included but we have lots of motors in the shop and all our DC motors, and stepper motors work great. Check out Adafruit's detailed tutorial for tons of info including schematics, wiring diagrams, python libraries and example walkthroughs.

R529.90  Inc VAT
Adafruit PiTFT 2.2" HAT Mini Kit - 320x240 2.2" TFT - No Touch (Ada no touch 2.2)

This product contains only the display. Raspberry Pi, case and cables are shown for illustration purposes only and not included.


The cute PiTFT got even more adorable with this little primary display for Raspberry Pi in HAT form! It features a 2.2" display with 320x240 16-bit color pixels. The HAT uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top of your Model A+ or B+ and fits into our case quite nicely.

It's designed to plug directly onto the Raspberry Pi 2 or Raspberry Pi 1 Model A+ or B+ . While not specifically designed for Pi Model A or B,you can use it with A/B if you solder in an extra-tall 2x13 header (not included) instead of the included 2x20 header.

This design uses the hardware SPI pins (SCK, MOSI, MISO, CE0, CE1) as well as GPIO #25. All other GPIO are unused and are available on a 25-pin long breakout line. Since we had a tiny bit of space, there's 4 flat tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button.

Comes as a fully assembled display PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. You can also swap the plain female header we have with a 'stacky' type that lets you plug in a hat or GPIO cable on top or a slim ultra-low-profile header.

Technical Details

  • Board Dimensions: 65mm x 57mm x 6mm / 2.6" x 2.2" x 0.2"
  • Screen Dimensions: 55mm x 40mm / 2.2" x 1.6"

Tutorials

To make it super easy for use: Adafruit have created a custom kernel package based of off Notro's awesome framebuffer work, so you can install it over your existing Raspbian (or derivative) images in just a few commands. Their tutorial series shows you how to install the software, play small videos, or display images such as from your PiCam and more!

R336.09  Inc VAT
R402.50
Unicorn HAT (Unicorn HAT)

What's going to protect your beloved Raspberry Pi from an onslaught of rainbow-coloured fusion? That's right, it's Unicorn HAT.

Sporting a matrix of 64 (8 x 8) RGB LEDs and powered directly from the Pi, this is the most compact pocket aurora available.

Unicorn HAT provides a wash of controllable colour that is ideal for mood-lighting, 8x8 pixel art, persistence of vision effects, status indications, or just blasting colour into your surroundings.

The MagPi said that Unicorn HAT was "one of the coolest HATs around"

Features

  • 64 RGB LEDs (WS2812B)
  • LED data driven via DMA over PWM
  • Unicorn HAT pinout
  • Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Comes fully assembled

Software

We've put together a Unicorn HAT Python library to make it a breeze to use, including lots of beautiful examples of what it can do.

Notes

  • Warning: WS2812 LEDs are bright enough to cause eye pain, do not look at them directly when brightly lit. We recommend the use of a diffuser.
  • Photo-sensitivity warning: flashing, strobing, and patterns of lights may cause epileptic seizures. Always take care and immediately stop using if you feel unwell (dizziness, nausea, affected vision, eye twitching, disorientation).
  • Power: Unicorn HAT requires a >2A microUSB power supply for your Pi. We recommend the official Raspberry Pi power supply.
  • Compatibility (audio): as Unicorn HAT uses PWM and GPIO18, it will interfere with analogue audio playback (random colour patterns and flickering). HDMI should work just fine!

Short video on the Unicorn HAT

Tutorials & Projects

R499.90  Inc VAT
WS 264x176 2.7 inch 3 colour E-Ink display HAT for Raspberry Pi (2.7 3colour E-Ink HAT)

Please Note: Raspberry Pi not included

Overview

This is an E-Ink display HAT for Raspberry Pi, 2.7inch, 264x176 resolution, with embedded controller, communicating via SPI interface, supports red, black, and white three-color display.

Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.

Features

  • No backlight, keeps displaying last content for a long time even when power down
  • Ultra low power consumption, basically power is only required for refreshing
  • Compatible with Raspberry Pi 2B/3B/Zero/Zero W
  • SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
  • Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Specifications

  • Operating voltage: 3.3V
  • Interface: 3-wire SPI, 4-wire SPI
  • Outline dimension: 85mm × 56mm
  • Display size: 57.288mm × 38.192mm
  • Dot pitch: 0.217 × 0.217
  • Resolution: 264 × 176
  • Display color: red, black, white
  • Grey level: 2
  • Full refresh time: 15s
  • Refresh power: 26.4mW(typ.)
  • Standby power: <0.017mW
  • Viewing angle: >170°

Please note: Raspberry Pi not included

Interface

SYMBOLDESCRIPTION
VCC3.3V
GNDGround
DINSPI MOSI pin
CLKSPI SCK pin
CSSPI chip selection, low active
DCData/Command selection (high for data, low for command)
RSTExternal reset, low active
BUSYBusy status output, low active

Development Resources

Wiki : www.waveshare.com/wiki/2.7inch_e-Paper_HAT_(B)

Package Includes:

  1. 2.7inch e-Paper HAT (B) x 1
  2. RPi screws pack (2pcs) x 2
R349.90  Inc VAT
ReSpeaker 2-Mics Pi pHAT (respeaker 2 microphones)

ReSpeaker 2-Mics Pi HAT is a dual-microphone expansion board for Raspberry Pi designed for AI and voice applications! This means that you can build a more powerful and flexible voice product that integrates Amazon Alexa Voice Service, Google Assistant, and so on with your Raspberry Pi!

The ReSpeaker is based on the Cirrus Logic WM8960, a low power stereo codec and features 2 microphones on both sides of the board for collecting sounds. It also provides 3 x APA102 RGB LEDs, 1 x User Button and 2 x on-board Grove interfaces for expanding your applications. What is more, 3.5mm Audio Jack or JST 2.0 Speaker Out are both available for audio output.

Note: This product does not include the Pi Zero board!

Features

  • Raspberry Pi compatible
  • pHAT Size
  • Dual-Microphones
  • 2 Grove Interfaces: Supports GPIO and I2C
  • Programmable Button and LED: 1 x button and 3 x LEDs
  • Cirrus Logic WM8960 Audio Codec
  • Two types audio output socket : 3.5mm Audio Jack, JST2.0 Speaker Out
  • Far field support (up to 3 meters)

Usage

1.Get started with Google Assistant

2.How to use button to trigger Google Assistant

Documentation

Please visit Seed Studio's wiki page for more info about this product. It will be appreciated if you can help us improve the documents, add more demo code or tutorials. For technical support, please post your questions to Seed Studio's forum.

R229.90  Inc VAT
Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit (adaf 16 servo control)

Control 16 Servos with perfect timing!

This HAT can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running.

For use with Raspberry Pi Model A+ or B+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20.

  • drive up to 16 servos or PWM outputs over I2C with only 2 pins.
  • The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead.
  • stack up to 62 HATs to control up to 992 servos - all with the same 2 pins!

Best of all, Adafruit even have a Python library you can use, so you'll be up and running instantly, to make your robotic creation com to life. The Adafruit PWM/Servo HAT is the perfect solution for any project that requires a lot of servos or PWM outputs! Check out Adafruits detailed tutorial for lots more information including diagrams, schematics, installation instructions and more

Each order contains

  • a Servo HAT
  • a 2-pin terminal block
  • four 3x4 headers
  • a 2x20 socket header

You'll need to do some light through-hole soldering to attach the headers onto the HAT circuit board. If you would like to stack multiple HATs onto one Pi, you can also pick up a 2x20 stacking header and a set of right-angle 3x4 headers that should be soldered on instead.

Please note! This kit does not come with Raspberry Pi, servos, or required 5V power supply.

R399.90  Inc VAT
ReSpeaker 4-Mic Array HAT (respeaker 4 microphones)

ReSpeaker 4-Mic Array for Raspberry Pi is a quad-microphone expansion board for Raspberry Pi designed for AI and voice applications. This means that you can build a more powerful and flexible voice product that integrates Amazon Alexa Voice Service, Google Assistant, and so on.

Different from ReSpeaker 2-Mics Pi HAT, this board is developed based on AC108, a highly integrated quad-channel ADC with I2S/TDM output transition for high definition voice capture. Besides, this 4-Mics version provides a super cool LED ring, which contains 12 APA102 programmable LEDs. With that 4 microphones and the LED ring, Raspberry Pi would have ability to do VAD (Voice Activity Detection), estimate DOA (Direction of Arrival) and show the direction via LED ring, just like Amazon Echo or Google Home.

Please note that the package does not contain Raspberry Pi.

Please note that there are no any audio output interfaces on ReSpeaker 4-Mic Array for Raspberry Pi. It is only for voice capture. And you could use the headphone jack on Raspberry Pi for audio output.

Here is a video from Parvinder Yadav, it teaches how to use ReSpeaker 4-Mic Array for Raspberry Pi  to make google assistant. We really appreciate Parvinder's contribution to the community and hope this video can be a good help for you.

https://youtu.be/uAQf0RKBNHo

Technical Details

  • Dimensions 65mm x 65mm x 9mm
  • Weight G.W 20g    
  • Battery Exclude
  • MIC 4 analog microphones
  • LED 12 APA102 programable RGB LEDs, connected to SPI interface
  • Raspberry Pi 40-Pin Headers support Raspberry Pi
  • AC108 highly integrated quad-channel ADC with I2S/TDM output transition
  • Software Algorithm VAD(Voice Activity Detection), DOA(Direction of Arrival) and KWS(Keyword Search)
  • Grove 2 Grove Interfaces
  • Voice Capture Distance 3 meters radius voice capture

Documents

ReSpeaker 4-Mic Array for Raspberry Pi is a quad-microphone expansion board for Raspberry Pi designed for AI and voice applications. This means that you can build a more powerful and flexible voice product that integrates Amazon Alexa Voice Service, Google Assistant, and so on.
R499.90  Inc VAT
WS True color RGB LED PHAT for Raspberry Pi (WS RGB LED PHAT)

Overview

This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.

Features

  • Supports any revision of Raspberry Pi (directly plugable)
  • Onboard 4 × 8 RGB LED (WS2812B)
  • Control pin is configurable via jumpers (0Ω resistor)
  • Break out control pins, easy for working with other MCUs
  • Comes with development resources and manual (examples in Python and Web control)

Specifications

  • Operating voltage: 5V
  • Brightness: adjustable 256 levels
  • Color depth: 24-bit true color (8-bit for R/G/B respectively, totally 256x256x256=16777216 colors)
  • Data rate: 800Kbps(typ)
  • Dimension: 65mm × 30.2mm
  • Mounting hole size: 3.0mm

How to Use

In the case of working with a MCU:

  • 5V ↔ 5V power
  • GND ↔ GND
  • DIN ↔ Signal input
  • DOUT ↔ Signal output (optional)

Development Resources

Wiki : www.waveshare.com/wiki/RGB_LED_HAT

This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R189.90  Inc VAT
WS .RGB LED HAT for Raspberry Pi, colorful display, 8 × 8 grid (WS RGB LED HAT)

Overview

This RGB LED HAT (B) can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.

Features

  • Supports any revision of Raspberry Pi (directly-pluggable)
  • Onboard 8 × 8 RGB LED (WS2812B)
  • Control pin is configurable via jumpers (0Ω resistor)
  • Break out control pins, easy for working with other MCUs
  • Comes with development resources and manual (examples in Python and Web control)

Specifications

  • Operating voltage: 5V
  • Brightness: adjustable 256 levels
  • Color depth: 24-bit true color (8-bit for R/G/B respectively, totally 256x256x256=16777216 colors)
  • Data rate: 800Kbps(typ)
  • Dimension: 65mm × 56.2mm
  • Mounting hole size: 3.0mm

How to Use

In the case of working with a MCU:

  • 5V ↔ 5V power
  • GND ↔ GND
  • DIN ↔ Signal input

Development Resources

Wiki : www.waveshare.com/wiki/RGB_LED_HAT_(B)

This RGB LED HAT can be easily attached on top of the Raspberry Pi to display colorful effect, and controlled by only one signal pin.
R241.10  Inc VAT
WS GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi (WS GSM/GPRS/GNSS/Bluetooth)

Please note: Raspberry Pi and micro SD in pic not included

Overview

This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.

It allows your Pi to easily make a telephone call, send messages, connect to wireless Internet, global position, transfer data via Bluetooth, and so on.

Features

General

  • Raspberry Pi connectivity, compatible with Raspberry Pi 2B/3B/Zero/Zero W
  • Supports SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc.
  • Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning
  • Bluetooth 3.0, supports data transferring through Bluetooth
  • Onboard USB TO UART converter CP2102 for UART debugging
  • 6x LEDs for indicating the module working status
  • SIM card slot for 1.8V/3V SIM card
  • RTC with backup battery holder
  • Baudrate auto detection (1200bps ~115200bps)
  • Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)
  • Supports SIM application toolkit: GSM 11.14 Release 99
  • Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

GSM/GPRS

  • Band
    • GSM 850/EGSM 900/DCS 1800/PCS 1900 MHz
    • Quad-band auto search
    • Compliant to GSM phase 2/2+
  • Emitting power
    • Class 4 (2W @ GSM 850/EGSM 900 MHz)
    • Class 1 (1W @ DCS 1800/PCS 1900 MHz)
  • GPRS connectivity
    • GPRS multi-slot class 12 (default)
    • GPRS multi-slot class 1~12 (configurable)
  • GPRS data feature
    • Downlink speed: max 85.6kbps
    • Uplink speed: max 85.6kbps
    • Coding schemes: CS-1\CS-2\CS-3\CS-4
    • Supports PAP (Password Authentication Protocol) for PPP connection
    • Supports PBCCH
    • Supports USSD
  • SMS
    • Supports: MT/MO/CB/Text/PDU mode
    • SMS storage: SIM card
  • Audio
    • Voice encode/decode mode: Half Rate\Full Rate\Enhanced Full Rate\Adaptive muti rate
    • Supports echo cancellation
    • Supports noise reduction

GNSS

  • Receiver type
    • 33 tracking channels
    • 99 acquisition channels
    • GPS L1 C/A code
  • Sensitivity
    • Tracking: -165 dBm
    • Cold starts : -148 dBm
  • Time-To-First-Fix
    • Cold starts : 28s (typ.)
    • Hot starts : < 1s
    • Warm starts: 26s
  • Accuracy
    • Horizontal position : <2.5m CEP

Bluetooth

  • Integrates AT commands
  • Compliant to Bluetooth specification3.0 + EDR
  • Supports SPP, OPP, HFP/HSP, etc.

Misc

  • Operating voltage: 5V
  • Operating temperature: -40°C ~ 85°C
  • Storage temperature: -45°C ~ 90°C
  • Dimensions: 30.2mm x 65mm

What's on Board

  1. SIM868 module
  2. ZMM5V1: regulator diode
  3. SMF05C: TVS diode
  4. CP2102: USB TO UART converter
  5. MP1482: power chip
  6. NDC7002N: voltage level translator
  7. GPS status indicator
  8. NET indicator:
    • flashes fast when the module starts up
    • flashes slowly after GSM register succeed
  9. STA module working status indicator
  10. SIM868 UART Tx/Rx indicator
  11. Power indicator
  12. SIM868 control button: press the button and hold for 1s, to startup/shutdown the SIM868
  13. Raspberry Pi GPIO connector
  14. SIM card slot
  15. USB TO UART interface
  16. 3.5mm earphone/mic jack
  17. GNSS antenna connector
  18. Bluetooth antenna connector
  19. GSM antenna connector
  20. CR1220 battery holder: for RTC backup battery
  21. UART selection switch
    • A: control the SIM868 through USB TO UART
    • B: control the SIM868 through Raspberry Pi
    • C: access Raspberry Pi through USB TO UART

Development Resources

Wiki : www.waveshare.com/wiki/GSM/GPRS/GNSS_HAT

This is a handy, low power Raspberry Pi HAT which features multi communication functionalities: GSM, GPRS, GNSS and Bluetooth.
R599.90  Inc VAT
Automation HAT (Automation HAT)

Take control of and monitor your world with our ultimate jack-of-all-trades Raspberry Pi HAT!

We've pulled together a great set of features into this home monitoring and automation controller. With relays, analog channels, powered outputs, and buffered inputs (all 24V tolerant) you can now hook up a plethora of goodies to your Raspberry Pi all at once.

Better still each channel has an indicator LEDs which means at a glance you can see what's happening with your setup. Even the analog channels have dimming LEDs that allow you to see the value they are currently sensing - swish!

Ideal for smart home and automation projects, giving your greenhouse intelligent sprinklers, or scheduling your fish feeding!

Features

  • 3 x 24V @ 2A relays (NC and NO terminals)
  • 3 x 12-bit ADC @ 0-24V
  • 3 x 24V tolerant buffered inputs
  • 3 x 24V tolerant sinking outputs
  • 15 x channel indicator LEDs
  • 1 x 12-bit ADC @ 0-3.3V
  • 3.5mm screw terminals
  • Power, Comms, and Warn! LED indicators
  • SPI, TX (#14), RX (#15), #25 pins broken out
  • Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Comes fully assembled (broken out pins require soldering)

Software

As ever, we've made a super-simple to use Python library to take advantage of Automation HAT's multitudinous functions, with examples to get you started.

Our input, output and relay examples show you how to read the analog and digital inputs, switch the outputs on and off, and control the relays.

Notes

  • We recommend you use a set of brass M2.5 standoffs with Automation HAT to avoid pins contacting the HDMI port if the HAT is pushed down
  • Loads for the buffered outputs should be switched on the ground side, i.e. 12/24V (from supply) -> load -> output terminal -> ground (from supply)
  • The relays can tolerate up to 2A each and should be switched on the high side
Take control of and monitor your world with our ultimate jack-of-all-trades Raspberry Pi HAT!
R639.90  Inc VAT
Li-ion Battery HAT for Raspberry Pi, 5V Output, Quick Charge (Battery hat zero)

Overview

The Li-ion Battery HAT integrates SW6106 power bank management chip, allows providing 5V regulated power supply to your Pi from a 14500 battery, makes the Pi becomes a portable device. It will charge the battery as well, supports bi-directional quick charge. This module can be used as a universal mini power bank, also works with other 5V devices.

Features

  • Onboard SW6106 chip, supports bi-directional quick charge, supports multi quick charge protocols like PD/QC/FCP/PE/SFCP
  • Lithium battery protection circuitry, provides reverse protection, over charge/discharge protection, over current protection, and short circuit protection
  • Onboard indicators: quick charge, warning, and power capacity

Specifications

  • Output voltage: 5V
  • Applicable battery: 3.7V 14500 lithium battery (4.2V when full charged)
  • Dimension: 65mm × 30mm
  • Mounting hole size: 3.0mm

What's on Board


  1. Raspberry Pi GPIO connector: for connecting Raspberry Pi
  2. SW6106 power management chip
  3. USB Type-C connector: battery charge/power output
  4. USB Type-A connector:power output
  5. Micro USB connector:battery charge
  6. Raspberry Pi power switch
  7. Battery warning indicator: on when the battery is reverse
  8. Battery power capacity indicator: 5x LEDs to indicate the power capacity and charging status
  9. Quick charge indicator: on when quick charging
  10. 14500 battery holder

Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/Li-ion_Battery_HAT

R289.90  Inc VAT
WS 4G / 3G / 2G / GSM / GPRS / GNSS HAT for Raspberry Pi, LTE CAT4 (4G Hat)

Please note: The Raspberry Pi is not included

Overview

The SIM7600E-H 4G HAT is a 4G/3G/2G communication and GNSS positioning module, which supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.

You can connect this 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc.

Features

  • Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B
  • Supports dial-up, telephone call, SMS, MMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc.
  • Supports GPS, BeiDou, Glonass, LBS base station positioning
  • Onboard USB interface, to test AT Commands, get GPS positioning data, and so on
  • Onboard CP2102 USB to UART converter, for serial debugging
  • Breakout UART control pins, to connect with host boards like Arduino/STM32
  • SIM card slot, supports 1.8V/3V SIM card
  • TF card slot for storing data like files, messages, etc.
  • Onboard audio jack and audio decoder for making telephone call
  • 2x LED indicators, easy to monitor the working status
  • Onboard voltage translator, operating voltage can be configured to 3.3V or 5V via jumper
  • Baudrate: 300bps ~ 4Mbps (default: 115200bps)
  • Autobauding baudrate: 9600bps ~ 115200bps
  • Control via AT commands (3GPP TS 27.007, 27.005, and V.25TER command set)
  • Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 99, USAT
  • Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Communications Specifications

 LTEWCDMA / TD-SCDMA / CDMA 2000EDGEGSM/GPRS
BandSIM7600E-H:
-- LTE-FDD B1/B3/B5/B7/B8/B20
-- LTE-TDD B38/B40/B41
SIM7600E-H:
-- UMTS/HSPA+ B1/B5/B8
GSM/GPRS/EDGE 900/1800 MHz
SIM7600CE-T:  
-- LTE-TDD B38/B39/B40/B41
-- LTE-FDD B1/B3/B8
SIM7600CE-T:
-- UMTS/HSDPA/HSPA+ B1/B8
-- TD-SCDMA B34/B39
-- CDMA 1X/EVDO BC0
Generation4G3G2.5G2G
Emitting power0.25W[email protected]
[email protected]
[email protected]
[email protected]
Data SpeedLTE CAT 4
Uplink≤50 Mbps
Downlink≤150 Mbps
UMTS
Uplink≤384Kbps
Downlink≤384Kbps
EDGE
Uplink≤236.8kbps
Downlink≤236.8kbps
GPRS
Uplink≤85.6kbps
Downlink≤85.6kbps
   HSPA+
Uplink≤5.76Mbps
Downlink≤42Mbps
      
SIM CardNormal SIM (Not Included)
Applicable RegionSIM7600E-H is mainly applicable in Southeast Asia, West Asia, Europe, Africa, SIM7600CE-T is mainly applicable in China.
Please check the supported bands according to your local service provider, select the proper one when placing order.

GNSS Specifications

  • Receiver type
    • 16-channel
    • C/A code
  • Sensitivity
    • Tracking: -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BD)
    • Cold starts: -148 dBm
  • Time-To-First-Fix (open air)
    • Cold starts: <35s
    • Hot starts: <1s
  • Accuracy
    • Position: <2.5m CEP

SMS and Audio Specifications

  • SMS
    • Supported types: MT, MO, CB, Text, PDU
    • Storage: USIM card and ME (default)
  • Audio feature
    • Supports echo cancellation
    • Supports noise reduction

Other Specifications

  • Power supply: 5V
  • Operating voltage: 5V/3.3V (configured via jumper)
  • Operating temperature: -30°C ~ 80°C
  • Storage temperature: -45°C ~ 90°C
  • Dimension: 56.21mm x 65.15mm

What's on Board

  1. SIM7600E-H
  2. CP2102 USB to UART converter
  3. NAU8810 audio decoder
  4. TXS0108EPWR voltage translator: translates 3.3V/5V into 1.8V
  5. MP2128DT power chip
  6. MP1482 power chip
  7. Raspberry Pi GPIO header: for connecting with Raspberry Pi
  8. SIM7600 control interface: for connecting with host boards like Arduino/STM32
  9. SIM card slot: supports 1.8V/3V SIM card
  10. TF card slot: allows file/SMS/... storage
  11. 3.5mm earphone/mic jack
  12. USB interface: for testing AT Commands, getting GPS positioning data, etc.
  13. USB to UART interface: for serial debugging, or login to Raspberry Pi
  14. MAIN antenna connector
  15. AUX antenna connector
  16. GNSS antenna connector
  17. Power switch
  18. Network status indicator
  19. Power indicator
  20. Operating voltage selection jumper:
    VCCIO - 3.3V: set operating voltage as 3.3V
    VCCIO - 5V: set operating voltage as 5V
  21. UART selection jumper:
    A: access Raspberry Pi via USB to UART
    B: control the SIM7600 by Raspberry Pi
    C: control the SIM7600 via USB to UART

Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/SIM7600E-H_4G_HAT



R1,499.90  Inc VAT
No EEPROM – Adafruit Perma-Proto HAT for Pi Mini Kit (Ada perma proto hat)

Adafruit Perma-Proto HAT for Pi Mini Kit

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi 3, 2, A+ or B+ with this jaunty prototyping HAT kit.

  • It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more.
  • The holes are connected underneath with traces to mimic the solderless breadboards you're familiar with.
  • There are also long power strips for +3V, +5V and Ground connections to the Pi.
  • Near the top we break out nearly every pin you could want to connect to the Pi (#26 didn't quite make the cut).

This is just the basic version of our Perma-Proto HAT.  It comes with a printed circuit board and a single 2x20 GPIO Header for Raspberry Pi to put your Perma-Proto on top of your Raspberry Pi (like a nice little hat...)


Example uses:
Weather station
reef-pi

R78.41  Inc VAT
R105.90
White – Scroll pHAT HD (HD scroll phat white)

Scroll pHAT HD

A whole heap of LED pixels with individual brightness control, for scrolling messages, animations, and more - Scroll pHAT HD!

Scroll pHAT HD packs 17x7 pixels (119 total) onto a single pHAT, and gives you full PWM brightness control over each pixel. Create beautiful animations and even anti-aliased text by taking advantage of the per-pixel brightness.

Now also available in beautiful coloured versions: red, orange, yellow, green, blue, and pink!

Use Scroll pHAT HD as a scrolling message display for your tweets, the weather or the news, or use it as a 17-band spectrum analyser for your audio. There's even enough pixels for simple games like Tetris, Pong, or snake.

Features

  • 17x7 matrix of bright white, or coloured, pixels (119 total)
  • Individual PWM brightness control of each pixel
  • Uses the IS31FL3731 LED matrix driver chip
  • Scroll pHAT HD pinout
  • Compatible with Raspberry Pi 3B+, 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Female header requires soldering

Software

Our handy one-line installer will install the Scroll pHAT HD Python library for you. We've included a bunch of examples too, to show off what you can do with Scroll pHAT HD.

Our software does not support Raspbian Wheezy.

R219.90  Inc VAT
Per Page      1 - 20 of 48