Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
This panel mount HDMI (Male to Female) extension cable will allow you to extend an HDMI connection and secure it to an enclosure!
R49.90  Inc VAT
R169.90  Inc VAT
40 PIN IDC SOCKET CABLE MOUNT HEADER (40-PIN IDC SOCKET)
Description:

These electrical connectors are designed for ribbon cables and telecommunications applications. They are also referred to as insulation-piercing contacts (IPCs).

Specifications:
  • 40 Pins Male Standard 0.1" 2.54mm Row spacing
  • Low Profile with mounting ears
  • 0.1" Pin spacing 0.1" Row spacing, Mates with IDC & PCB male Receptacles
  • Insulation Displacement Connector terminates to 0.050" (1.27mm) flat ribbon cable
What's in the box:

1 x 40-PIN IDC SOCKET CABLE MOUNT
R11.90  Inc VAT
Liquid Water level sensor Side Mounted Float Switch (liquid level side mounted)

Description:

The liquid level switch detects the rising level of liquid in a sump or tank. It can be connected to a micro controller. It can then be used to start/stop a pump which then pumps liquid in/out until the level of the liquid has been restored to the point where the pump is switched off again. The switch may be used in a pump station, a sensor, a tank alarm, or other devices.

 

Specification:

Contact Rating: 10W
Switching Voltage: 220V
Switching Current: 0.5A
Breakdown Voltage: 220VDC
Carry Current: 1.0A
Contact Resistance: 100mohm

What's in the box:

1 x Liquid Water level sensor 

Resources:

Python library
Introduction to Buttons and Switches
Types of buttons and switches

 

R39.90  Inc VAT
Raspberry Pi MF Standoff HAT Mounting Kit(11mm) (MF hat mounting kit)
Description:

Need to securely mount your Raspberry Pi HAT to your Raspberry Pi? You need our HAT mounting kit!

The 11mm spacers in the kit fit between the Pi PCB and the HAT, and can be secured using the included M2.5 bolts and nuts.

What's in the box?:

  • 4 x M2.5 x 11mm Male to Female Standoffs
  • 4 x M2.5 +5 Bolts
  • 4 x M2.5 Nuts
R19.90  Inc VAT
Panel Mount Ethernet - RJ45 Male to RJ45 Female (panel mount RJ45)
Description:

This handy Ethernet extension cable will make it easy for you to enclose a device that has an Ethernet port. It's extra short (5cm between connectors), so perfect for mounting your Raspberry Pi, Beagle Bone, Arduino etc. into a box!

The jack half has two mounting 'ears' with M3 screws installed, 8mm apart. The ears are flexible so the holes don't have to drilled very precisely.

Our Panel Mount RJ45 Cable Features:

  • Specially Manufactured for ModMyPi for use with the Raspberry Pi & Other Microcontrollers
  • Length between connectors: 5cm
  • Colour: Black
  • RJ45 Male to Panel Mount RJ45 Female
  • Patch Cable
  • M3 Mounting Ears (Two M3 x 6mm Screws Included)
R34.90  Inc VAT
Panel Mount - USB A Male to USB A Female 30cm (panel mount USB AmAf)

Description:

This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. It's short (30cm between connectors), so perfect for mounting your Raspberry Pi, Beagle Bone, Arduino etc. into a box!

The jack half has two mounting 'ears' with M3 screws installed, 8mm apart. The ears are flexible so the holes don't have to drilled very precisely.

Our Panel Mount USB Cable Features:

  • Specially Manufactured for ModMyPi for use with the Raspberry Pi & Other Microcontrollers 
  • Length between connectors: 30cm
  • Colour: Black
  • 28AWG
  • USB A Male to Panel Mount USB A Female
  • M3 Mounting Ears
What's in the box:

1 x USB A Male to Panel Mount USB A Female
R29.90  Inc VAT
Panel Mount HDMI Cable 0.4m (panel mount hdmi)
Description:

This panel mount HDMI (Male to Female) extension cable will allow you to extend an HDMI connection and secure it to an enclosure!

Perfect for placing your Raspberry Pi in a secure box, the panel mount uses two #4-40 (M3) screws to attach the female socket end! The panel mount screw holes are 26.9mm apart.

This cable is 0.4m long (about 16 inches), and is a V1.4 CEC enabled cable.

Specifications:

• 1x HDMI male connector
• 1x HDMI panel mount female port
• Offers 0.4m cable length
• Customize your solutions – mount a HDMI port on your PC or Pi through an available HDMI female connector
• Guaranteed reliability

What's in the box?:

1 x HDMI panel mount cable

This panel mount HDMI (Male to Female) extension cable will allow you to extend an HDMI connection and secure it to an enclosure!
R49.90  Inc VAT
Camera Mount Tripod Black/White with phone bracket (Camera tripod)
Description:

Great for mounting your phone to film your latest project for youtube, or for mounting your Raspberry Pi HQ camera for stable safe use.

1) flexible joints, and can rotate 360 to form the desired shape
2) The ring and foot clamp provide additional grip for most of the surface
3) Link attachment lock your camera tripod to make it safe
4) Your camera can be used anywhere in this tripod
5) support professional SLR camera tripod head and zoom lens.
6) For: tripod mountable camera and professional tripod head
7) Adapter: Universal 1/4-in plus a tripod screw 3/8-inch adapter
8) Size: about 165 × 35 × 35mm


Specifications:


Applies to: small size cameras
Tripod weight: 45 grams
Interface: Standard 1/4 "screw

Package Includes:

1 x small octopus tripod
R99.90  Inc VAT
10pcs 28x28MM Black Self-adhesive Cable TiE-mounts Positioning Pieces (black cable tie mount(10))
Description:

The mounts are made of nylon 6.6, which is tough, insulated and chemical resistant. Easy to install, it can be used for securing various sorts of things by using a cable tie. Perfect for organizing cables.
Advised to stick the mount after removing the dust from the sticking surface for a better adhesive effect.


Specifications:

Material: Nylon 6.6 & Polyethylene foam with a high performance rubber adhesive.
Color: Black
Base Size: 28x28mm
Height: (approx.) 7.8mm
Max. Tie Size: (approx.) 6mm
Fire Rating: 94-2
  
Package includes

10 x 28x28mm Self-adhesive Cable Tie Mounts
R42.90  Inc VAT
Raspberry Pi 8-channel Relay Expansion Board with DIN rail mounting brackets (DIN rail relay board)
Please note: Raspberry Pi is not included

Overview

The RPi Relay Board (B) is an expansion board with 8-ch relays for Raspberry Pi. It gives your Pi the ability to control high voltage products such as home appliances.

Features
  • Supports Raspberry Pi A /B /2B/3B/3B /4B
  • High quality relays, loads up to 5A 250V AC or 5A 30V DC
  • Photo coupling isolation, prevent interference from high voltage circuit
  • Standard rail mount bottom case
  • Onboard LEDs for indicating relays status
  • Relay control pin selection jumper, allows to control the relays by custom pins other than the default pins
  • Reserved control Interface, allows to work with controllers like PLC
  • Comes with development resources, including examples in wiringPi, bcm2835, python, python-bottle (webpage control), and crontab (cron job)
Specifications
  • Power supply voltage: 5V
  • Trigger signal: 3.3V/5V
  • Relay channels: 8-ch
  • Contact form: SPDT-NO,NC
  • Closed current: 6mA (per channel)
  • Connector: screw terminal block
  • Dimension: 232 × 72 (mm)
  • Mounting hole size: 3.0mm
Dimensions

Development Resources

Wiki : www.waveshare.com/wiki/RPi_Relay_Board_(B)

R359.90  Inc VAT
Machifit 24V NEMA17 Stepper Motor with 400mm T8 Lead Screw Mounted Ball Bearing and Shaft Coupling (24V stepper with T8 screw and nut)

Specifications:
Lead screw 
Materialstainless steel
Diameter8mm
Pitch2mm
Lead4
Total Length400mm
Screw nut 
Materialbrass
Diameter
8mm
Pitch2mm
Lead4
Mounted ball bearing 
Materialzinc alloy
Bore diameter8 mm8mm
Total length55mm
Height29mm
Shaft coupling 
Materialaluminium
Shaft6.35 x 8 mm
Length25 mm
Diameter20mm
Motor 
Voltage24V
Step angle1.8°
Accuracy of step angle ±5%
Accuracy of resistance±10%
Accuracy of inductance±20%
Insulation resistance100mΩmin 500VDC
Radial clearance0.02Max
Axial clearance0.08Max
Radial maximum tolerance28N
Axial maximum tolerance10N
 
Features:
3D printer T8 400mm Stainless Steel Lead Screw Screw nut Mounted ball bearing Shaft coupling Motor.
Screw mainly use for Stepping motor driving guide rail,machine tool, and other equipment.
Screw without processing, direct connected to bearing.
T shape design, make of high quality stainless steel material.
Easy to install and convenient to use.
Fine producing and practical.
Suitable for Industrial automation equipment, stepper motor rails;
Fit for 3D printer; engraving machine; XYZ module; slider; lifts ect.

How to install:
1. Put screw nut into the lead screw.
2. Then the 2 Mounted ball bearing separately install at both ends of the Lead screw.
3. According to the size of you need to adjust the distance between the nut and Mounted ball bearing.
4. Put shaft coupling into the Lead screw beside the Mounted ball bearing.
 
Package Includes:
1 x 400mm Lead screw
1 x Screw nut
2 x Mounted ball bearing
1 x Shaft coupling
1 x Motor
R729.90  Inc VAT
Wall Mounting Bracket (wall mount bracket)
Description

This wall mounting bracket can be used to mount your Raspberry Pi case to a wall or bench! It can be used with our PIR Camera Case for Raspberry Pi 4/3. Coupled with a Raspberry Pi case, this wall mounting bracket enables the use of your Raspberry Pi as a flexible monitoring system, with a variable angle of operation. The bracket itself allows the mounted object to be tilted or swiveled, and fixed using thumb screws when it's located in the correct position.

Each bracket can support up to 3.5kg, can be mounted to wooden stud or brick/concrete/hollow-block walls, and includes the hardware necessary for either type of mounting option. Additionally, the kit includes M5 x 12 bolts for mounting a device to the brackets.

Please note. This purchase is for the wall mounting bracket, and mounting hardware only

The Wall Mounting Bracket Kit Includes:

  • 1 x Wall Mounting Bracket
  • 2 x M5 x12 Bolts
  • 2 x M5 Nuts
  • 2 x Wall / Ceiling M4 x 25 Mounting Screws
  • 2 x Plastic Anchors

The Wall Mounting Bracket Kit Features:

  • Tilt angle: -24° to 15°
  • Swivel angle: ~75° left and right
  • Thumb screws for easy angle adjustments
  • Bracket max. weight: up to 3.5kg (7.7 lbs)
R169.90  Inc VAT
Panel Mounted Glass Fuse Holder 5x20mm (fuse holder 5x20mm)
Description:

Fuse holders can be used in any applications where you need to ensure electrical protection, isolation and switching under load of inductive or resistive loads. The technology solutions applied to reduce power dissipation help to minimize module heating.

Fuse holders are suitable for protection against overloads and short circuits.

Quality rubber fuse-holder fits ATC/ATO size fuses. Holds and encloses fuse securely. Hinged cover protects fuse from impact, water and dust. 12-inch wire loop is made of 18 gauge flexible stranded red wire.


Features:

- Panel mounted fuse holder suitable for 5 x 20mm type fuses.
- With screw cap and solder-lug terminals.

Specifications:

- Material: Plastic Metal
- Color: Black
- Current rating: 10A ( 250V AC ) / 15A ( 125V AC )
- Fuse size: 5 x 20mm
- Cutting hole: 12.5mm
- Length: 35mm

Package Includes:
1 x Fuse Holder
R34.90  Inc VAT
T8 400mm Lead Screw Set with Shaft Coupling and Mounted Ball Bearing (T8 400mm Lead Screw Set)
Description:

These are 4 start 8mm pitch leadscrews with a 200 steps per revolution motor and the 16x microstepping on most common 3D printers. This adds up to 400 steps per mm 3200 steps/ 8mm per rev = 400 steps /mm the same as most 3d Printer lead screws use.

Specifications:


Lead screw 
Materialstainless steel
Diameter8mm
Lead
2mm
Total Length
500mm
Screw nut 
Material:brass
Diameter8mm
Mounted ball bearing 
Materialzinc alloy
Bore diameter5mm
Hole diameter
8mm
Total length55mm
Height29mm
Shaft coupling 
Materialaluminium
Shaft6.35 x 8mm
Length24mm
Diameter18mm
Quantity1 set ( 1 screw 1 Screw nut 2 Mounted ball bearing 1 shaft coupling)

Features:
  • Screw mainly used in stepper motors, machine tools, and other CNC equipment.
  • Screw directly connected to bearing.
  • Suitable for Industrial automation equipment, stepper motor rails, 3D printers, engraving machines, XYZ modules, slider, lifts etc.

How to install:

1. Put screw nut onto the Lead screw.
2.Then the 2 Mounted ball bearing separately, install at both ends of the Lead screw.
3. According to the size of you need to adjust the distance between the nut and Mounted ball bearing.
4. Put shaft coupling into the Lead screw beside the Mounted ball bearing.
 
Package Includes:

1 x Lead screw
1 x Screw nut
2 x Mounted ball bearings
1 x Shaft coupler
R499.90  Inc VAT
Machifit SHF8 Horizontal Linear Rail/Shaft Support for CNC (AW SHF8 Rail/Shaft Support)
Specification:
Type: SHF8
Shaft Dimension: 8mm
Material : Aluminum Alloy
Uasge: used for supporting the two sides on a linear rail/shaft.
 
Package Included:
1 x Linear Rail Shaft Support 
R34.90  Inc VAT
Interior Panel Mount Temperature Meter - Celsius (Temp panel mount)
Description

Battery powered panel-mount temperature display. Suitable for basic room or environment monitoring.

Features

  • Material: Plastic
  • Indoor temperature °C display.
  • It comes with a mounting clips which allows it to be panel mounted
  • Temperature range: -50 ~ 70 Degrees.
  • Usage temperature: -10 ~ 50 Degrees.
  • Usage humidity:  5% ~ 80%
  • Accuracy:  /-01 Degrees.
  • Distinguishing temperature: 0.1 Degrees.
  • Power: 2 x DC1.5V AG13 button batteries (Not included)
  • Cable length:  0.8M.
  • Size:  48 x 28 x 15(mm)
  • Color:  Black


Package Includes:

1 x LCD Digital Thermometer Temperature Sensor
R56.90  Inc VAT
Raspberry Pi4 Mounting Plate for High Quality Camera (HQ pi4 mount plate)

Note: The Raspberry PiHigh Quality Camera and flexible tripod not included)

Description

An affordable, simple solution to mounting your Raspberry Pi to your Raspberry Pi High Quality Camera.

Easy to assemble, the plate attaches to your High Quality Camera on one side, and your Raspberry Pi mounts to the other side – spacers and fixings are included in the pack.

Available for different Raspberry Pi models

It’s a lightweight and minimal way to keep your Raspberry Pi and High Quality Camera together, which saves any fuss with camera cable lengths and cases.

HATs and pHATs can still be mounted to your Raspberry Pi, meaning you can create amazing projects with screens, buttons, RTCs or any others.

Combine with our affordable flexible tripod for a great project foundation!

 Kit contents:

  • 1x Mount plate
  • 4x 6mm female-female nylon spacers
  • 8x M2.5 nylon nuts
  • 8x 5mm M2.5 nylon screws
  • 4x 10mm M2.5 nylon screws

Assembly:

Assembly guide available here!

R69.90  Inc VAT
Raspberry Pi ZERO Mounting Plate for High Quality Camera (HQ ZERO mount plate)

Note: The Raspberry PiHigh Quality Camera and flexible tripod not included)

Description

An affordable, simple solution to mounting your Raspberry Pi to your Raspberry Pi High Quality Camera.

Easy to assemble, the plate attaches to your High Quality Camera on one side, and your Raspberry Pi mounts to the other side – spacers and fixings are included in the pack.

Available for different Raspberry Pi models

It’s a lightweight and minimal way to keep your Raspberry Pi and High Quality Camera together, which saves any fuss with camera cable lengths and cases.

HATs and pHATs can still be mounted to your Raspberry Pi, meaning you can create amazing projects with screens, buttons, RTCs or any others.

Combine with our affordable flexible tripod for a great project foundation!

 Kit contents:

  • 1x Mount plate
  • 4x 6mm female-female nylon spacers
  • 8x M2.5 nylon nuts
  • 8x 5mm M2.5 nylon screws
  • 4x 10mm M2.5 nylon screws

Assembly:

Assembly guide available here!

R69.90  Inc VAT
Hygrometer Thermometer Digital LCD Temperature Humidity Meter 10%~99%RH (Hygrometer Thermometer)
Description:

High Quality Hygrometer, wonderful tools for Indoor, Outdoor, Home, Laboratory, Library..etc.


Specifications:

Color: Black
Measuring humidity: 10%RH-99%RH
Humidity accuracy: 5%
Humidity display resolution: 1% RH
Measuring temperature range: -50 centigrade~ 70 centigrade
Temperature accuracy: 1 centigrade
Temperature display resolution: 0.1centigrade .
Operating voltage: 2 x 1.5V button LR44 batteries (Not included)
Dimension: 4.7x2.8x1.5cm(approx.)
LCD dimension: 3.6x1.7cm(approx.)


Package includes:

1 x Humidity Hygrometer Meter
R69.90  Inc VAT
HDMI-HDMI D Type Female Socket Panel Mounted Connector (HDMI panel connect no cable)
Description:

Ideal for connecting 2 HDMI cables together to create single longer cable. Or to extend your HDMI port when mounting your device

Specifications:
  •     Type: D type HDMI chassis connector
  •     Style: panel mounted
  •     Colour: black
  •     Material: zinc alloy
  •     Application: Audio,Video


What's in the box?:

1 x female HDMI panel mounted connector
R79.90  Inc VAT
Raspberry PI camera adjustable mounting bracket for camera V2 (V2 camera mount plates)
Please note: The camera and cable is not included

Description:

Designed for the hole pattern of the RPi Camera Module v2.
Adjustable Pi Camera mount is a great accessory for Pi shutterbugs. Little screws attach the Pi Camera solidly and the design allows for multiple positions. 





  • Allows four different angles of repose
  • Four Screws to secure your camera
  • Made from black acrylic
  • hole for tripod mounting

R69.90  Inc VAT
Per Page      1 - 20 of 27