Search
Search Criteria
Products meeting the search criteria
This is suitable for taking apart any small electronics, like cell phones or portable gaming systems and for soldering projects.
8-bit WS2812 5050 RGB LED Ring Development Board (RGB ring 8)
Description:
Voltage: DC 5V
Colour: RGB
An Outer radius of 2 x 28mm, an inner radius of 2 x 8mm
Soldering will be required to connect your wires
What's in the box?
1 x 8 Bit WS2812 5050 RGB LED Driver Development Board
Voltage: DC 5V
Colour: RGB
An Outer radius of 2 x 28mm, an inner radius of 2 x 8mm
Soldering will be required to connect your wires
What's in the box?
1 x 8 Bit WS2812 5050 RGB LED Driver Development Board
CJMCU 24 Bit WS2812 5050 RGB LED Driver Development Board (RGB ring 24)
Description:
Voltage: DC 5V
Colour: RGB
Outer diameter 85mm, 70mm inner diameter
Soldering will be required to connect your wires
What's in the box?
1 x 24 Bit RGB LED Driver Development Board
Voltage: DC 5V
Colour: RGB
Outer diameter 85mm, 70mm inner diameter
Soldering will be required to connect your wires
What's in the box?
1 x 24 Bit RGB LED Driver Development Board
HC-SR04 Ultrasonic Sensor Distance Measuring Module (sensor ultrasonic blue)
Description:
This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit.
There are only four pins that you need to worry about on the HC-SR04: VCC (Power), Trig (Trigger), Echo (Receive), and GND (Ground). You will find this sensor very easy to set up and use for your next range-finding project!
Specifications:
- Model: HC-SR04
- Color: Blue Silver
- Working voltage : 5V(DC)
- Static current: Less than 2mA.
- Output signal: Electric frequency signal, high level 5V, low level 0V.
- Sensor angle: Not more than 15 degrees.
- Detection distance: 2cm~450cm.
- High precision: Up to 3mm
- Mode of connection: VCC / trig(T) / echo(R) / GND
- Module Working Principle:
- Adopt IO trigger through supplying at least 10us sequence of high level signal
- The module automatically send eight 40khz square wave and automatically detect whether it receive the returning pulse signal
Resources:
A good tutorial available at ModMyPi.
http://www.modmypi.com/blog/hc-sr04-ultrasonic-range-sensor-on-the-raspberry-pi
Read the Docs
What's in the box:
1 x HC-SR04 distance sensor
This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit.
There are only four pins that you need to worry about on the HC-SR04: VCC (Power), Trig (Trigger), Echo (Receive), and GND (Ground). You will find this sensor very easy to set up and use for your next range-finding project!
Specifications:
- Model: HC-SR04
- Color: Blue Silver
- Working voltage : 5V(DC)
- Static current: Less than 2mA.
- Output signal: Electric frequency signal, high level 5V, low level 0V.
- Sensor angle: Not more than 15 degrees.
- Detection distance: 2cm~450cm.
- High precision: Up to 3mm
- Mode of connection: VCC / trig(T) / echo(R) / GND
- Module Working Principle:
- Adopt IO trigger through supplying at least 10us sequence of high level signal
- The module automatically send eight 40khz square wave and automatically detect whether it receive the returning pulse signal
Resources:
A good tutorial available at ModMyPi.
http://www.modmypi.com/blog/hc-sr04-ultrasonic-range-sensor-on-the-raspberry-pi
Read the Docs
What's in the box:
1 x HC-SR04 distance sensor
2-Axis FPV Camera Cradle Head w/ 9g Dual Servo / Steering Gear for Robot / R/C Car - Black Blue (cam pan/tilt bracket)
You'll have to know how to control this unit from you GPIO port or a servo controller module(Not included).
Description:
Specially designed for R/C car and robotics; Can be pan/tilt 180 degrees; Can hold ultrasonic sensor, IR sensor, camera or other sensors.
Specifications:
- Weight: 15g
- Working torque: 1.6KG/cm
- Response rotary speed: 0.10s / 60 degree
- Working temperature: -30~60'C
- Dead zone: 2ms
- Plug: JR, Futaba
- Rotating angle: Max. 180 degree
- Servo: digital servo
- Working current: 0.02A
- Working voltage: 3.5~6V
- Structure: Nylon plastic gear
What's in the box?:
1 x Cradle head w/ servo (25.6 /-2cm)
1 x Pack of screws
Description:
Specially designed for R/C car and robotics; Can be pan/tilt 180 degrees; Can hold ultrasonic sensor, IR sensor, camera or other sensors.
Specifications:
- Weight: 15g
- Working torque: 1.6KG/cm
- Response rotary speed: 0.10s / 60 degree
- Working temperature: -30~60'C
- Dead zone: 2ms
- Plug: JR, Futaba
- Rotating angle: Max. 180 degree
- Servo: digital servo
- Working current: 0.02A
- Working voltage: 3.5~6V
- Structure: Nylon plastic gear
What's in the box?:
1 x Cradle head w/ servo (25.6 /-2cm)
1 x Pack of screws
DC 5V Waterproof Ultrasonic Module Distance Measuring Transducer Sensor (waterproof ultrasonic)
Description:
This waterproof ultrasonic distance sensor is for those applications that are a bit more rugged! 25cm - 450cm sensing range.
We have used the HC-SR04 Ultrasonic Distance Sensor many times and for many good reasons. It is pretty easy to use, it performs well, and it is very inexpensive. For collision avoidance robots or intruder detection, this sensor is usually all you’ll need.
However, using the HC-SR04 outside is a different story. It is a pretty fragile device and can easily be damaged by dirt, or even high winds. And, above all, it is not waterproof.
For these circumstances you can use this sensor, in more weathered states, even outdoors
Specifications:
Operating voltage: DC 5V
Total current work: 40mA
Acoustic emission frequency: 40khz
Maximum distance: 4.5m
Blind: 25cm
Wiring:
5V (positive power supply)
Trig (control side) RX
Echo (the receiver) TX
GND (negative)
Resolution: about 0.5cm
Angle: 70 degrees
Working temperature: -10 ~ 70 ℃
Storage temperature: -20 ~ 80 ℃
Product Features:
- small size, easy to use;
- low voltage, low power consumption;
- high accuracy;
- strong anti-jamming;
- integrated with wire enclosed waterproof probe, suitable for wet, harsh measuring conditions.
Application:
1 Horizontal distance;
2 obstacle avoidance, automatic control;
3 traffic control;
4 security, industrial control;
5 artificial intelligence, and research
Basic working principle:
(1) using IO port TRIG trigger location, to the high level signal of at least 10us;
(2) module automatically sends 8 40KHz pulse, automatic detecting whether a signal returns;
(3) on signal return, a high level is output through the IO port ECHO, the time duration of the high level is ultrasonic from launch to return. The test distance = (high level time * speed of sound (340M/S)) /2;
Usage
Package Includes:
1 x DC 5V Waterproof Ultrasonic Module Distance Measuring Transducer Sensor
This waterproof ultrasonic distance sensor is for those applications that are a bit more rugged! 25cm - 450cm sensing range.
We have used the HC-SR04 Ultrasonic Distance Sensor many times and for many good reasons. It is pretty easy to use, it performs well, and it is very inexpensive. For collision avoidance robots or intruder detection, this sensor is usually all you’ll need.
However, using the HC-SR04 outside is a different story. It is a pretty fragile device and can easily be damaged by dirt, or even high winds. And, above all, it is not waterproof.
For these circumstances you can use this sensor, in more weathered states, even outdoors
Specifications:
Operating voltage: DC 5V
Total current work: 40mA
Acoustic emission frequency: 40khz
Maximum distance: 4.5m
Blind: 25cm
Wiring:
5V (positive power supply)
Trig (control side) RX
Echo (the receiver) TX
GND (negative)
Resolution: about 0.5cm
Angle: 70 degrees
Working temperature: -10 ~ 70 ℃
Storage temperature: -20 ~ 80 ℃
Product Features:
- small size, easy to use;
- low voltage, low power consumption;
- high accuracy;
- strong anti-jamming;
- integrated with wire enclosed waterproof probe, suitable for wet, harsh measuring conditions.
Application:
1 Horizontal distance;
2 obstacle avoidance, automatic control;
3 traffic control;
4 security, industrial control;
5 artificial intelligence, and research
Basic working principle:
(1) using IO port TRIG trigger location, to the high level signal of at least 10us;
(2) module automatically sends 8 40KHz pulse, automatic detecting whether a signal returns;
(3) on signal return, a high level is output through the IO port ECHO, the time duration of the high level is ultrasonic from launch to return. The test distance = (high level time * speed of sound (340M/S)) /2;
Usage
Package Includes:
1 x DC 5V Waterproof Ultrasonic Module Distance Measuring Transducer Sensor
SC8UU 8mm Aluminium Linear Motion Ball Bearing Slide Bushing For CNC (Linear 8mm Bearing Slide)
Description :
The universal Ball Bearings is great for you to replace the damaged Ball Bearings in your devices to improve efficiency and save energy.
Widely used in home appliances, industrial, low noise and high speed electric motors, construction machinery, automotive components, pumps, and machinery. Smooth moving, low friction, high rigidity and long life. Economical, easy to maintain replace.
Specifications :
Model : SC8UU
Material : Steel, Aluminum
Size : Approx. 34 x 30 x 22cm / 1.34 x 1.18 x 0.87"
Inner Diameter : Approx. 8mm / 0.31"
Package included :
1x SC8UU Linear Motion Ball Bearing
The universal Ball Bearings is great for you to replace the damaged Ball Bearings in your devices to improve efficiency and save energy.
Widely used in home appliances, industrial, low noise and high speed electric motors, construction machinery, automotive components, pumps, and machinery. Smooth moving, low friction, high rigidity and long life. Economical, easy to maintain replace.
Specifications :
Model : SC8UU
Material : Steel, Aluminum
Size : Approx. 34 x 30 x 22cm / 1.34 x 1.18 x 0.87"
Inner Diameter : Approx. 8mm / 0.31"
Package included :
1x SC8UU Linear Motion Ball Bearing
F695ZZ 5mmx13mmx4mm Double Shielded Flanged Ball Bearings (F695ZZ Flanged Bearing 5x13x4mm)
Description:
Manufactured to the same principal sizes as standard bearings but fitted with metal shields, these bearings have an additional flange to allow fitting into housings flush against the shoulder of the flange. They are often used on steel tracks as guides and supports. The shields serve to offer protection to prevent ingress of debris and dust whilst retaining the grease within the bearing
Specifications:
Features: Package Includes:
1 x Ball Bearing
Manufactured to the same principal sizes as standard bearings but fitted with metal shields, these bearings have an additional flange to allow fitting into housings flush against the shoulder of the flange. They are often used on steel tracks as guides and supports. The shields serve to offer protection to prevent ingress of debris and dust whilst retaining the grease within the bearing
Specifications:
| Model | F695ZZ |
| Material | Chrome Steel |
| Size | 5 x 13 x 4mm |
| Quantity | 1pcs |
Easy to install and replace.
Less friction and higher speed.
Smooth operation, high accuracy.
Smooth operation, high accuracy.
Durable.
1 x Ball Bearing
SCS8UU/SK8 8x200mm Optical Axis Linear Ball Bearing Rail Guide Support CNC Set (8x200mm linear parts kit)
1 x Linear shaft rod
1 x Fixed shaft support
1 x Pillar block bearing SCS12UU
Description:
The linear motion bearing kit is made of carbon steel, linear Bearings made of GCr15 bearing steel with aluminum alloy housing.
Widely applied in CNC, 3D printer, automatic machinery, injection molding machine, engraving machine, etc. especially in bearing purpose
Perfect combination of main shaft rod rail and aluminum alloy support, which nicely stabilizes the original rail.
The linear motion bearing kit is made of carbon steel, linear Bearings made of GCr15 bearing steel with aluminum alloy housing.
Widely applied in CNC, 3D printer, automatic machinery, injection molding machine, engraving machine, etc. especially in bearing purpose
Perfect combination of main shaft rod rail and aluminum alloy support, which nicely stabilizes the original rail.
Specifications:
- Material: 45# carbon steel(chrome plated)
- Accuracy: G6 level
- Hardness: HRC58-60 degree
- Length: 200mm
- Diameter: 8mm
Package Includes:
1 x Linear shaft rod
1 x Fixed shaft support
1 x Pillar block bearing SCS12UU
Speed Measuring Sensor Module (speed measure sensor)
Description:
Uses improved groove optical coupling sensor, width 5mm. Has an output state light, if output level is high, the lights are off. If output is low,light is on. If the sensor is covered, it will output a high level.
Feature:
Uses improved groove optical coupling sensor, width 5mm.
It has an output state light, if output level is high, the lights are off. If output is low,light is on.
If sensor is covered,it will output a high level.
Working voltage of 3.3V to 5V.
Output: digital switch output (0 and 1).
Equipped with a fixed bolt hole, easily install.
Small board PCB size: 32 mm x 14 mm.
Use the LM393 wide voltage comparer.
Wiring specifications:
VCC Connect positive 3.3 to 5V power supply
GND Connect power negative
DO TTL switch signal output
AO Not used
Package includes:
1 x Speed Measuring Sensor Module
Uses improved groove optical coupling sensor, width 5mm. Has an output state light, if output level is high, the lights are off. If output is low,light is on. If the sensor is covered, it will output a high level.
Feature:
Uses improved groove optical coupling sensor, width 5mm.
It has an output state light, if output level is high, the lights are off. If output is low,light is on.
If sensor is covered,it will output a high level.
Working voltage of 3.3V to 5V.
Output: digital switch output (0 and 1).
Equipped with a fixed bolt hole, easily install.
Small board PCB size: 32 mm x 14 mm.
Use the LM393 wide voltage comparer.
Wiring specifications:
VCC Connect positive 3.3 to 5V power supply
GND Connect power negative
DO TTL switch signal output
AO Not used
Package includes:
1 x Speed Measuring Sensor Module
Used in motor speed detection, pulse count, position limit, etc.
Spring Washer M5 (10 pack) (spring washers M5(10))
Description:
Spring washers also called split lock washers, provide a vibration resistant function, they consist of ring split at one point and bent into a helical shape, this causes the washer to exert a spring force between the fastener's head and the bearing face which maintains the washer hard against the face and the bolt thread hard against the nut or threaded hole, creating more friction and resistance to rotation
Specifications:
What's in the box:
10 x Spring washers
Spring washers also called split lock washers, provide a vibration resistant function, they consist of ring split at one point and bent into a helical shape, this causes the washer to exert a spring force between the fastener's head and the bearing face which maintains the washer hard against the face and the bolt thread hard against the nut or threaded hole, creating more friction and resistance to rotation
Specifications:
- Spring Washer
- M5
- Pack of 10
What's in the box:
10 x Spring washers
Spring Washer M4 (10 pack) (spring washers M4(10))
Description:
Spring washers also called split lock washers, provide a vibration resistant function, they consist of ring split at one point and bent into a helical shape, this causes the washer to exert a spring force between the fastener's head and the bearing face which maintains the washer hard against the face and the bolt thread hard against the nut or threaded hole, creating more friction and resistance to rotation
Specifications:
What's in the box:
10 x Spring washers
Spring washers also called split lock washers, provide a vibration resistant function, they consist of ring split at one point and bent into a helical shape, this causes the washer to exert a spring force between the fastener's head and the bearing face which maintains the washer hard against the face and the bolt thread hard against the nut or threaded hole, creating more friction and resistance to rotation
Specifications:
- Spring Washer
- M4
- Pack of 10
What's in the box:
10 x Spring washers
25x35cm Heat Resistant Soldering Station Pad (Solder pad blue)
Description:
This is suitable for taking apart any small electronics, like cell phones or portable gaming systems and for soldering projects.
Features:
This is suitable for taking apart any small electronics, like cell phones or portable gaming systems and for soldering projects.
Features:
1. Work surface to perform detailed DIY projects.
2. Pre-Printed grid designed to help you keep parts organized.
Specification:
Heat-resistant Repair Pad Size: approx. 350mm x 250mm x 5mmGross weight: approx. 260g
Heat resistance: 350 °C
Package includes:
1 x Heat-resistant Repair Pad
This is suitable for taking apart any small electronics, like cell phones or portable gaming systems and for soldering projects.
Soldering Iron 1230 25W 220V (Magnum solder 1230 hand)
Description:
The Soldering Iron 1230 is the perfect iron for hobbiests, DIY home makers or someone who only has an occasional use for a Soldering Iron. The 1230 plugs straight into the wall, requiring no workstation at all. Soldering has never been so simple.
Specifications:
What's in the box?
1 x Soldering iron
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
The Soldering Iron 1230 is the perfect iron for hobbiests, DIY home makers or someone who only has an occasional use for a Soldering Iron. The 1230 plugs straight into the wall, requiring no workstation at all. Soldering has never been so simple.
Specifications:
- 220v 25w Thermally balanced soldering iron.
- Temperature at rest ± 400 °C
- Stainless steel element and barrel.
- Long life iron-plated tips.
- Support stand.
- Plugs into any 220v AC power source.
What's in the box?
1 x Soldering iron
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
Magnum Soldering Iron Stand (Magnum solder iron stand)
Description:
A much needed accessory for the entire range of Magnum Soldering Irons and Soldering Stations.
This Magnum cast iron soldering spring stand allows for a clean, safe and organised work surface. Included with a cellulose sponge.
What's in the box?
1 x Soldering iron stand
1 x Soldering Sponge
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
Soldering Station SM2000 50W (Magnum station 2000)
Description:
The Soldering Station 2000 comes standard with the Soldering Iron 1000sp. They have been designed to operate together.
Specifications:
1 x Solder station
1 x Solder sponge
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
The Soldering Station 2000 comes standard with the Soldering Iron 1000sp. They have been designed to operate together.
Specifications:
- General purpose 24vAC 50w transformer station.
- Safety-spring holder.
- Cleaning sponge.
- Spare tip storage.
- Potential balance socket.
- Supplied with standard SM100003 tip (EW-303)
1 x Solder station
1 x Solder sponge
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
CMT Welding Soldering Solder Iron Tip Cleaner Gold Cleaning Wire with Stand (solder tip cleaner pot)
Description:
Color : Gold
Size : 70mm x 69mm x 69mm
1 x Iron Tip Cleaner
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
No water necessary, maintain temperature for the iron to faster work cycle.
It cleans better than conventional sponges.
It cleans better than conventional sponges.
Specifications :
Color : Gold
Size : 70mm x 69mm x 69mm
Package includes :
1 x Iron Tip Cleaner
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
Soldering Station SM2002 50W (Magnum station 2002)
Description:
The Soldering Station 2002 with total temperature control comes standard with the Soldering Iron 1002. They are designed to operate together.
Specifications:
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
The Soldering Station 2002 with total temperature control comes standard with the Soldering Iron 1002. They are designed to operate together.
Specifications:
- Stepless temperature selection between 150°C & 450°C (302°F & 842°F)
- Thermocouple sensing to maintain tip temperature within ± 5°C of selected temperature.
- Electronic proportional control varies the heating period as required to maintain set temperature.
- Heating pulse indicator.
- Units earthed with potential balance socket.
- Triac switching at zero-crossover point.
- Robust ABS cabinet.
- Illuminated rocker switch.
- Safety-spring holder.
- Cleaning sponge.
- Spare tip storage.
- Potential balance socket.
- Supplied with standard SM100003 tip (EW-303)
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
| Input | 220/240v 50/60Hz external 500mA fuse |
| Output | 24v AC 2A (50W model) |
| Size | L200mm W120mm H110mm (without spring holder) |
| Weight | 1,8Kg |
MS Flux PEN for DIY Solar cell Panels and soldering projects (Misol flux pen)
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
Description:
Refillable flux pens for all your rework needs including no-clean, rosin and water soluble. Liquid Solder Flux Pen is used to clean PCB track and legs or pins of electronic components while soldering.
Specifications:
- No-Clean Flux
- Net volume: 10ml
- Shelf life @ 25 degree C: 2 year
- Push the pen tip to start the flux flow
- Keep the pen cap on when not in use
Warning:
- When coming into contact with skin, please wash the area immediately to avoid skin irritation.
- Do not consume.
- Please store in a safe location where children can not reach it.
Resources:
Introduction to soldering
Video: How to solder properly
The secrets to good soldering
2.0mm 1.5m Desoldering Braided Solder Remover Wick (2mm desolder wick)
Description:
Desoldering braid or “wick” is a pre-fluxed copper braid that is used to remove solder, which allows components to be replaced and excess solder (e.g. bridging) to be removed.
Specifications:
Type : CP-2015
Length : 1.5M
Width : 2.0mm
How to use :
1.Place the desoldering wick over the solder to be removed,then put the heated soldering iron tip onto the desoldering wick.The solder will be absorbed.
2.Remove the desoldering wick after the solder has been absorbed.
3.Cut off the used section of the wick using nippers.
4.Repeat steps 1,2 and 3 if the solder is not removed completely.
Absorption may differ depending on the type of solder.Sn63% and 60% (tin content) have good absorption ability.
Package Includes :
1 x 2.0mm 1.5m Desoldering Wick CP-2015
Resources:
How to desolder
Desoldering braid or “wick” is a pre-fluxed copper braid that is used to remove solder, which allows components to be replaced and excess solder (e.g. bridging) to be removed.
Specifications:
Type : CP-2015
Length : 1.5M
Width : 2.0mm
How to use :
1.Place the desoldering wick over the solder to be removed,then put the heated soldering iron tip onto the desoldering wick.The solder will be absorbed.
2.Remove the desoldering wick after the solder has been absorbed.
3.Cut off the used section of the wick using nippers.
4.Repeat steps 1,2 and 3 if the solder is not removed completely.
Absorption may differ depending on the type of solder.Sn63% and 60% (tin content) have good absorption ability.
Package Includes :
1 x 2.0mm 1.5m Desoldering Wick CP-2015
Resources:
How to desolder
4pcs Springs For 3D Printer Extruder Heated Bed (4 bed springs)
Description:
These springs are stiffer which should result in a more consistent bed level with reduced vibrations.
Features:
1. Super elastic
2. Nickel plating for better corrosion resistance and surface hardness
Specifications:
Wire diameter: 1.2mm
Inner diameter: 5mm
Outside diameter 7.5mm
Height: 20mm
Material: stainless steel
Circle number: 9
Package includes:
4 x Springs
These springs are stiffer which should result in a more consistent bed level with reduced vibrations.
Features:
1. Super elastic
2. Nickel plating for better corrosion resistance and surface hardness
Specifications:
Wire diameter: 1.2mm
Inner diameter: 5mm
Outside diameter 7.5mm
Height: 20mm
Material: stainless steel
Circle number: 9
Package includes:
4 x Springs