Search
Search Criteria
Products meeting the search criteria
ModMyPi Paddle Breakout HAT (1B2 Paddle Hat)
PLEASE NOTE: RASPBERRY PI IS NOT INCLUDED
The ModMyPi Paddle Breakout HAT enables you to bring the Raspberry Pi B+/2/3 GPIO out from your Raspberry Pi to 'push wire' paddle terminal points in the form of a neat HAT! This kit requires absolutely no soldering, but will allow you to jump straight from the Pi to your project or breadboard without the use of a cobbler kit. All terminals are labelled on the PCB silkscreen, and have been re-ordered in a simple to use format.
The 'push wire' terminals can be utilised with solid core wire stripped to around 10mm of exposed copper.
The ModMyPi Paddle Breakout HAT Features:
- Fully Labelled Silkscreen for Easy Identification
- Push Wire Terminals for Quick & Easy Connections
- Pre-assembled HAT - No Soldering Required
- Includes 40 Pin HAT Header - Plug & Play
- Includes M2.5 Stand-Off's for Mounting
- Manufactured in the UK!
One way Solid State Relay Module (2A3 Solid state relay single)
Description:
Package included:
1 x One way Solid State Relay Module
Relay tutorial for Raspberry Pi
5V Omron solid state relays 240V / 2A, output with resistive fuse 240V / 2A.
Dimensions: 25x34x25 (length x width x height)
Input Power: 5VDC
Control signal input voltage: (0-2.5V low state relay ON) (3-5V state high relay OFF)
Feature:
Voltage:5V
Quiescent current: 0 mA
Operating current: 12.5mA
Trigger Voltage: 3.3-5V
Trigger current: 2mA
Feature:
Voltage:5V
Quiescent current: 0 mA
Operating current: 12.5mA
Trigger Voltage: 3.3-5V
Trigger current: 2mA
DC +: positive power supply (according to the relay voltage supply)
DC-: negative power supply
CH1: relay module signal triggering end (low to trigger active)
Package included:
1 x One way Solid State Relay Module
Relay tutorial for Raspberry Pi
Four Way Solid State Relay Module (2A3 solid relay 4 red)
Description:
5V Omron solid state relays 240V / 2A, output with resistive fuse 240V / 2A.
Dimensions: 57x55x25 (length x width x height)
Input Power: 5VDC
Control signal input voltage: (0-2.5V low state relay ON) (3-5V state high relay OFF)
Features:
Voltage:5V
Quiescent current: 0 mA
Operating current: 12.5mA
Trigger Voltage: 3.3-5V
Trigger current: 2mA
Features:
Voltage:5V
Quiescent current: 0 mA
Operating current: 12.5mA
Trigger Voltage: 3.3-5V
Trigger current: 2mA
DC +: positive power supply (according to the relay voltage supply)
DC-: negative power supply
CH1: relay module signal triggering end (high to trigger active)
CH2: relay module signal triggering end (high to trigger active)
CH3: relay module signal triggering end (high to trigger active)
CH4: relay module signal triggering end (high to trigger active)
Package includes:
1 x Four way Solid State Relay Module
Python Code
CH2: relay module signal triggering end (high to trigger active)
CH3: relay module signal triggering end (high to trigger active)
CH4: relay module signal triggering end (high to trigger active)
Package includes:
1 x Four way Solid State Relay Module
Python Code
Solid State Relay SSR-50DA 3-32VDC 50A/250V Output 24-380VAC w/ Cover (2A6 3-32V relay solid state)
Specification:
Package Includes:
1 X 50A SSR-50DA Solid State Relay With Cover
Datasheet available at https://cdn.sparkfun.com/datasheets/Components/General/SSR40DA.pdf
Depending on how hard your relay works, you might want to add a heat sink to it.
Q:During continuity testing with my multimeter why does my relay on the AC side not switch on?
A: The below info was found at http://www.crydom.com/en/tech/newsletters/solid%20statements%20-%20bench%20test%20an%20ssr.pdf
A multimeter determines impedance by injecting a small amount of voltage through it's probes into the circuit being tested. It then measures the current flowing through the probes and calculates resistance. Easy enough; Resistance = Voltage / Current! However, as we just discussed above, a solid state relay’s output turns on by “stealing” a bit of voltage from the AC mains in order to supply current to the gate of the SCRs. Simply put, if the AC mains is not connected to the relay then the output cannot turn on. Since the voltage and current produced by a multimeter is not sufficient enough to turn on the SCRs, the output of a solid state relay will remain in the off state; even with the input signal applied. As a result, SSRs will sometimes fail an incoming inspection because the engineer expects to see a significant change in the output impedance when they turn on the relay.The most effective way to bench test a solid state relay is to construct a simple test circuit consisting of a DC power supply or battery (a 9Vdc battery will work fine in most cases ) and a 60W or 100W light bulb.
| Size | 62mm(L)x44mm(W)x23mm(H) |
| Input Voltage (Trigger) | DC 3-32V |
| Output Voltage(Line) | AC 24-380V |
| Output Current(Line) | 50 A |
| On Voltage | ≤1V |
| On-Off Time | ≤10ms |
| Off Leakage Current | ≤2mA |
| Transparent Lid Included | Yes |
Package Includes:
1 X 50A SSR-50DA Solid State Relay With Cover
Datasheet available at https://cdn.sparkfun.com/datasheets/Components/General/SSR40DA.pdf
Depending on how hard your relay works, you might want to add a heat sink to it.
Q:During continuity testing with my multimeter why does my relay on the AC side not switch on?
A: The below info was found at http://www.crydom.com/en/tech/newsletters/solid%20statements%20-%20bench%20test%20an%20ssr.pdf
A multimeter determines impedance by injecting a small amount of voltage through it's probes into the circuit being tested. It then measures the current flowing through the probes and calculates resistance. Easy enough; Resistance = Voltage / Current! However, as we just discussed above, a solid state relay’s output turns on by “stealing” a bit of voltage from the AC mains in order to supply current to the gate of the SCRs. Simply put, if the AC mains is not connected to the relay then the output cannot turn on. Since the voltage and current produced by a multimeter is not sufficient enough to turn on the SCRs, the output of a solid state relay will remain in the off state; even with the input signal applied. As a result, SSRs will sometimes fail an incoming inspection because the engineer expects to see a significant change in the output impedance when they turn on the relay.The most effective way to bench test a solid state relay is to construct a simple test circuit consisting of a DC power supply or battery (a 9Vdc battery will work fine in most cases ) and a 60W or 100W light bulb.
One Roll 8 Colors 30AWG Wrapping Wire Tinned Copper Solid PVC insulation (1C2 multi colour wrapping wire)
Description:
- Material: Plastic and Metal
- Total length of about 280M Line: 30AWG
- Single sheath outer diameter of about: 0.55mm, copper core diameter of about 0.25mm.
- Temperature: 80 degrees, single-strand copper crossing tin, have antioxidant effects.
Packaging:
- 1 x PCB Test Core Line Single Tinned Copper Wire 8-color Board Cable Roll
Aluminum Alloy Heat Sink For Solid State Relay SSR Heat Dissipation (SSR relay heat sink)
Description:
Brand new and high quality.
New heat sink for solid state relay SSR
Aluminium alloy
Come with a aluminum heat sink provides long lasting usage, it will help dissipate the heat and protect your relay.
Solid State Relay ideal for automatic process control application, a must component for temperature controller and other machinery control system.
Specification:
Materail: Aluminium alloy.
Size:Roof:50mm x 60mm.Foot:80mm x 50mm.
Height:43mm.
Weight:96g
Compatible with:Designed specially for single phase solid state relay.
Color :Silver
Package includes:
1 x Solid state relay heat sink
Brand new and high quality.
New heat sink for solid state relay SSR
Aluminium alloy
Come with a aluminum heat sink provides long lasting usage, it will help dissipate the heat and protect your relay.
Solid State Relay ideal for automatic process control application, a must component for temperature controller and other machinery control system.
Specification:
Materail: Aluminium alloy.
Size:Roof:50mm x 60mm.Foot:80mm x 50mm.
Height:43mm.
Weight:96g
Compatible with:Designed specially for single phase solid state relay.
Color :Silver
Package includes:
1 x Solid state relay heat sink
- 1