Search
Search Criteria
Products meeting the search criteria
This Starter Kit is based around the Raspberry Pi Pico development board which features the Raspberry Pi RP2040 microcontroller chip. 
Whats in the box:
- The Raspberry Pi Pico microcontroller
- USB A male to USB micro B male 1.5m cable
- 2.54mm Pitch Single Row Pin Header 40-PIN - Black
- 5V 2A EU Power Supply Micro USB AC Adapter for Pico
Add wifi to Pico using Cricket
https://www.thingsonedge.com/post/pico-cricket-blynk-phone-alerts
The official Raspberry Pi USB-C power supply is designed to power the latest Raspberry Pi 4 Model B computers, which were released in June 2019.
Featuring a captive USB-C cable, the power supply is available in four different models to suit different international power sockets, and in two colours, white and black.
If you need to use the power supply for an earlier model RPi or the zero you'll need a type C to micro B adapter than you will find at https://www.pishop.co.za/store/rpi-power/usb-type-c-female-to-micro-usb-male-adapter
Specifications
Output
- Output voltage: +5.1V DC
- Minimum load current: 0A
- Nominal load current: 3.0A
- Maximum power: 15.3W
- Load regulation: ±5%
- Line regulation: ±2%
- Ripple & noise: 120mVp-p
- Rise time: 100ms maximum to regulation limits for DC outputs
- Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
- Protection: Short circuit protection, Overcurrent protection, Over temperature protection
- Efficiency: 81% minimum (output current from 100%,75%, 50%, 25%)72% minimum at 10% load
- Output cable: 1.5m 18AWG
- Output connector: USB Type-C
Input
- Voltage range: 100-240Vac (rated)
- 96-264Vac (operating)
- Frequency: 50/60Hz ±3Hz
- Current: 0.5A maximum
- Power consumption (no load): 0.075W maximum
- Inrush current: No damage shall occur and the input fuse shall not blow
UL94V-1
AC pin material
Brass (NI plated)
WARNINGS
• This product should be operated in a well-ventilated environment.
• The connection of incompatible devices to this power supply may affect compliance, result in damage to the unit and invalidate the warranty.
SAFETY INSTRUCTIONS
To avoid malfunction or damage to this product please observe the following:
• Do not expose to water or moisture, or place on a conductive surface whilst in operation.
• Do not expose to heat from any source; this is designed for reliable operation at normal ambient room temperatures.
• Do not attempt to open or remove the power supply case.
What is in this box?
- The Raspberry Pi 400 with US keyboard
- The Official Raspberry Pi 3A USB type C Power Supply
- The Official Raspberry Pi micro USB to USB 1m HDMI cable
- The Official Raspberry Pi Beginner's Guide
- The Official Raspberry Pi Red/White USB mouse
- Sandisk uSD with Raspberry Pi OS pre-installed
Overview
Featuring a quad-core 64-bit processor, wireless networking, dual-display output and 4K video playback, Raspberry Pi 400 is a complete personal computer, built into a compact keyboard.
Raspberry Pi 400 is ideal for surfing the web, creating and editing documents, watching videos, and learning to program using the Raspberry Pi OS desktop environment.
Raspberry Pi 400 is available in a number of different regional variants and as either a computer kit, containing everything you need to get started (except for a TV or monitor), or a computer unit only.
Raspberry Pi 400 for working and learning at home
Specifications
Processor: Broadcom BCM2711 quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.8GHz
RAM: 4GB LPDDR4-3200
Connectivity: Dual-band (2.4GHz and 5.0GHz) IEEE 802.11b/g/n/ac wireless LAN, Bluetooth 5.0, BLE Gigabit Ethernet
2 × USB 3.0 and 1 × USB 2.0 ports
GPIO Horizontal 40-pin GPIO header
Video & sound: 2 × micro HDMI ports (supports up to 4Kp60)
Multimedia: H.265 (4Kp60 decode);
H.264 (1080p60 decode, 1080p30 encode);
OpenGL ES 3.0 graphics
SD card support: MicroSD card slot for operating system and data storage
Keyboard: 78- or 79-key compact keyboard (depending on
regional variant)
Power: 5V DC via USB type C connector
Operating temperature: 0°C to +50°C
Dimensions: 286 mm × 122 mm × 23 mm (maximum)
Compliance: For a full list of local and regional product approvals, please visit
www.raspberrypi.org/documentation/hardware/raspberrypi/conformity.md
WARNINGS
• Any external power supply used with Raspberry Pi 400 shall comply with relevant regulations and
standards applicable in the country of intended use.
• This product should be operated in a well-ventilated environment and should not be covered when
being operated.
• The connection of incompatible devices to Raspberry Pi 400 may affect compliance, result in damage to the unit, and invalidate the warranty.
• There are no user-serviceable parts inside Raspberry Pi 400, and opening the unit is likely to damage the product and will invalidate the warranty.
• All peripherals used with this product should comply with relevant standards for the country of use
and be marked accordingly to ensure that safety and performance requirements are met. These
articles include, but are not limited to, mice, monitors and cables when used in conjunction with
Raspberry Pi 400.
• The cables and connectors of all peripherals used with this product must have adequate insulation so that relevant safety requirements are met.
• Prolonged exposure to direct sunlight may cause discoloration.
SAFETY INSTRUCTIONS
To avoid malfunction or damage to this product please observe the following:
• Do not expose to water or moisture whilst in operation.
• Do not expose to heat from any source; Raspberry Pi 400 is designed for reliable operation at normal ambient temperatures.
• Take care whilst handling to avoid mechanical or electrical damage to the computer.
Accreditation
Get started with the Raspberry Pi with one of our pre-boxed kits
These kits are perfect for beginners that are just just getting exposed to the Raspberry Pi, Media enthusiasts looking to stream online content with Kodi, developers looking to exploit the many advantages of the RPI's GPIO pins and anybody looking to get some cool goodies at a great price! They contain all of the essential items that you need to get up and running in no time.
Please Note: These kits are pre-boxed and cannot be modified at all, we do however keep stock on all of the individual items so if you have a special need simply feel free to browse through the rest of our product offerings and select the items that you'd like.
The kit is availible in a number of options and comes equipped with:
- The Iconic Raspberry Pi 4 Model B 4GB
- An Official 5V 3A Power Supply in White
- A 1m micro HDMI cable
- 32 GB Micro SD card with Raspberry Pi OS pre-installed
- An Official Pi4 Red/White Case
Want to take your kit to the next level?
Turn your RPI into a Media Centre
Grab yourself a remote control, select LibreELEC or OSMC when setting up your RPI and you'll be streaming in no time. You can even add a wireless keyboard, mouse or other similar controllers
Want a cheap eco-friendly PC
Grab a Keyboard and Mouse, select Raspbian when setting up your RPI and you'll be browsing the web, sending emails, editing spreadsheets and watching videos just like you're used to with a desktop/laptop.
We know you love retro gaming!
Check out our Arcade section, whether you just want a retro control or a mini DIY arcade cabinet we have what you're looking for.
Did somebody say Robotics?
We've got some cool beginner's items in our robotic section
Our Kits come with the latest version of NOOBS – New Out Of the Box Software pre-installed, While we will certainly try our best to assist with any software related questions we cannot offer any kind of official support on community driven, open source, or non-PiShop produced proprietary software.
NOOBS, Raspbian, LibreELEC and OSMC are all open-source software, please visit the developer's respective websites for more info.
So what is NOOBS anyway?In Short, NOOBS is an installer, when you switch your RPI on NOOBS will guide you through the installation of your software of choice... seem confusing? Don't worry it really couldn't be easier
- Raspbian - a full desktop for normal day to day work. Email, internet, office suite, programming etc.
- LibreELEC RPi2 - our preferred version of Kodi for use as a media centre.
- OSMC Pi2 - for more control of your Kodi media centre
- Windows 10 IoT Core - nope this is not windows 10. It simply enables you to run projects and apps for the IOT environment.
- Lakka and Recalbox - retro gaming for the RPi.
A whole bunch of other really cool technical info can be found here.
Getting Started with Raspberry Pi
You'll need a USB Type C adapter to use this supply for Pi 4
The Official Raspberry Pi Power Supply - Shipped with easily interchangeable heads for the UK, US, EU and Australia you can now use your Pi in all four corners of the world!
This PSU supports up to 2.5A of current, so it won't let you down when powering hungry devices through your Raspberry Pi 3 Model B
Technical Data
- 5.1V 2.5A Output
- 1.5m Cable
- White with Raspberry Pi Logo
- Input Voltage AC Max: 264V
- Input Voltage AC Min: 90V
- Output Connector: USB Micro
- Output Voltage Nom.: 5.1V
- Interchangeable Adaptor - EU/UK/US/AUS
The below is a copy from https://www.raspberrypi.org/help/faqs/#powerReqs.Here is a table comparing the amount of power drawn in amps under different situations:
Test conditions used a standard Raspbian image (current as of 26 Feb 2016),Pi1 (B+) Pi2 B Pi3 B (Amps) Zero (Amps) Boot Max 0.26 0.40 0.75 0.20 Avg 0.22 0.22 0.35 0.15 Idle Avg 0.20 0.22 0.30 0.10 Video playback (H.264) Max 0.30 0.36 0.55 0.23 Avg 0.22 0.28 0.33 0.16 Stress Max 0.35 0.82 1.34 0.35 Avg 0.32 0.75 0.85 0.23
| Model | I061806 |
| Quantity | 1 |
| Color | Black |
| Material | PCB |
| Features | Input voltage: 6.5~12 V (DC) or USB power supply; Output voltage: 3.3V / 5V switchable; Maximum output current: <700 mA; Two ways individual control: 0V / 3.3V switchable |
| Application | Suitable for MB102 breadboard |
| Other | For Arduino/Raspberry Pi/Electronic DIY projects |
| Packing List | 1 x Power supply module |
Dimensions: 2.09 in x 1.26 in x 0.39 in (53 mm x 32 mm x 10 mm)
Weight: 1.62 oz (46 g)
Quick video available on a similar MB-102 power supply at https://www.youtube.com/watch?v=ZpCep1jL-iA
UBEC's (Universal Battery Eliminator Circuit's) are simply DC to DC step down voltage regulators! This UBEC is perfect for the Raspberry Pi, as it's able to take high voltages (5.5V up to 26V), and outputs a consistent safe voltage of 5V at up to 3A nominal or 5A max! The Hobbywing 5V 3A UBEC is a switch-mode type, which results in it being much more efficient than linear type UBEC's (so your batteries will last longer!)
UBEC's are perfect for applications where you plan to use the Raspberry Pi in a circuit with high voltages such as robots where you'll be driving motors!
Due to the voltage drop caused by the Raspberry Pi, it is recommended to input a minimum of 6.5V to receive a stable 5V output. Anything lower than 6.5V will result in a low voltage warning on the Pi.
Please Note. The Hobbywing UBEC can be set to output either 5V or 6V using an onboard jumper select! Please DOUBLE CHECK your output voltage is correct before connecting your microcontroller or circuit!
Features
- Designed with an advanced switch mode DC-DC regulator IC.
- Battery polarity reversal protection.
- A metal shield covers almost all the electronic components, and a specially made filter is attached to the output wires to significantly reduce the electromagnetic interference.
- The working status is shown by an indicator (LED), which lights when the output is in normal range.
- Output Voltage: [email protected] or [email protected] (Changeable with an output-voltage select jumper)
- Continuous output current: 3 Amps
- Maximum output current: 5 Amps
- Input: 5.5V - 26V (2 - 6 cells lithium battery pack or 5 - 18 cells NiMH /NiCd battery)
- Size: 43mm*17mm*7mm (L*W*H)
- Weight: 11g
Check out our tutorial here: https://www.modmypi.com/blog/using-a-ubec-with-a-raspberry-pi
Dimension: 16.7 x 5.7 x 1cm
Tie Points: 830 tie points (consists of: 630 tie-point terminal strips, 200 tie-point distribution strips)
Matrix: 126 separate 5 point terminals, plus 4 horizontal bus lines (Power Lines) of 50 test points each
Jumper size: Suitable for 20~29 AWG (0.3mm ~ 0.8mm) wires
MB-102 Power Supply Module:
Input voltage: 6.5V ~ 12 V DC / USB power supply
Output voltage: 3.3V / 5V select with jumpers
Maximum output current: <700mA
Fluctuation two road independent control, can switch over to 0V, 3.3V, 5V
On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use
Size: 5.3 x 3.2 x 2.5cm
Jumper Cables:
Breadboard jumper cable male to male
Typically used for electronics projects
Wires are flexible, durable, reusable, easy to trace
Easy to connect and disconnect
Kit includes:
1 x 830 tie point Solderless Breadboard
1 x MB-102 Breadboard Power Supply
65 x Breadboard Jumper Cables male to male
This battery box is designed for use as a nice switchable, portable power pack, and fits any two alkaline or rechargeable AA batteries in series. The body is moulded in black ABS Resin and has a slide on detachable lid which can be locked for extra security through use of a small provided screw. It even includes a very useful miniature on-off slide switch which is very handy for wiring to projects that don't have a switch! Connection is via two flexible stranded red (positive) & black (negative) 26AWG wire leads, which are approximately 150mm in length.
- Battery Cell Size AA
- Number of Cells 2
- Body Material ABS Resin
- Height 19.0 mm, Length 68.0 mm, Width 33.0 mm
- Terminal Type Wire Lead
- Type Battery Box
- Weight 0.01900 kg
Here are the links of the CE Certification and the Environmental Certification:
CE Certification:
https://www.dropbox.com/s/x937yu696g449o2/CE%20Certification%20.pdf?dl=0
Environmental Certification:
https://www.dropbox.com/s/38ncgzktlsxlhvw/Environmental%20Certification%20.pdf?dl=0
Brand: Machifit
| Dimensions | 140mm×110mm×48mm (L*W*H) |
| Input | AC220V±10% 50/60Hz |
| Spindle Motor | 500w |
| Spindle Speed | 3000-12000r/min |
| Motor Diameter | 52mm |
| Motor Length | 208mm |
| Operating Voltage | 100V DC |
| Current | 6A |
| Speed | Up to idle up to 15,000 rev / min |
| Torque | 5000G/CM |
| Insulation Resistance | > 2 megohms |
| Dielectric Strength | 400V |
| High precision spindle runout 0.01-0.03 | |
Chuck size:
Small diameter: 7.8mm
Nut Size:
Inner Diameter: 8.7mm
Height: 13mm
Hex Diameter: 17mm
Outer Diameter:19mm
The Usage of "Don't pipe":
Its function is to inhibit the switched source. If they are open, the source does not give tension.
If the short circuits, for example with a relay, the source generates the voltage to which it is regulated with the potentiometer.
There will be no problem in controlling the motor using these pins.
Voltage:10A AC250V
Contact Resistance:≤0.03Ω
Withstand voltage:AC 1500V(50hz)/min
Insulation Resistance:≥100MΩ
Insertion and Extrartion Force:3-20N
Dielectric intensity:≥2000V AC/min
Temperature:-40℃ to 70℃
Color:Black
Package includes:
1x power supply socket
Overload protection
Short circuit protection
Over temperature protection
Input:100-240V AC 50/60Hz
Output: DC 9V 1000mA
Plug: EU Plug
Dimension: 70mm x 80mm x 28mm
Cable length: about 100cm
DC Plug Dimension: 5.5mm x 2.5mm
Color: Black
EU type
Description:
The Gert VGA 666 (6 bits per colour channel, hence 666) is a breakout/add-on board for the Raspberry Pi Model B+ (will not work with Model A/B as the additional GPIO pins on the Model B+ are required). It is an open source hardware design recently released publicly by Gert van Loo who was one of the hardware engineers that was instrumental in the initial design of the original Raspberry Pi (also one of the chip architects on the BCM2835 chip at the heart of the Raspberry Pi) and someone that many of you may have spoken to at Raspberry Jams or on the Raspberry Pi forums. It is a neat and very useful solution for using a VGA screen/monitor with your Raspberry Pi and is far cheaper than an HDMI to VGA adapter or similar. The VGA connection is driven natively in hardware over the GPIO pins (using a parallel interface) and uses around the same CPU load as the HDMI connection on board. It is capable of displaying 1080p60 VGA video with no CPU load. It is also possible to drive this interface at the same time as the HDMI connection, so a dual screen setup is also possible. This add-on was not possible on the Model A and B pis, because not all of the required pins had been brought out to the GPIO header. Yet another awesome upgrade that the Model B+ has allowed for!
Please note: this add-on on board uses all but 6 of the GPIO pins on the Model B+ Raspberry Pi so it may not be possible to use other add on boards at the same time as the VGA adapter. Why a kit? We love electronics kits for a multitude of reasons - they are fun to put together, you get a sense of achievement at the end of it, they are great for learning about soldering and electronics and many many more reasons... At Pi Supply we are quite keen on the whole education and fun aspect of the Raspberry Pi and computing and electronics in general, so we feel that a kit is much more worthwhile to all of our backers. However, you don't need to be a soldering god or an electronics pro to put our kits together - Gert has made this simple enough even for absolute beginners to put together. The images in this project show surface mount resistors, however, for the purposes of the kit we will be supplying all through hole components. There was also a concern about EMC (electromagnetic compatibility) regulations which could cause a problem if made as a fully assembled board. This regulation does not cover home made electronics and so a kit makes more sense for this reason as well.
Specifications:
- Uses all but 6 of the GPIO pins on the Model B+ Raspberry Pi
- 6 bits per colour channel, hence 666
- Will not work with Raspberry Pi 1 Model A/B
- Open source hardware design
- BCM2835 chip
- VGA Connector
Contents:
- 1 x Gert VGA 666 PCB
- 1 x 40 pin GPIO header connector
- 1 x 15 pin female VGA connector
- 20 x through hole resistors (2*120 Ohm, 3*499 ohm, 3*1kOhm, 3*2kOhm, 3*4kOhm, 3*8kOhm, 3*16kOhm)
- 2 x Pi Supply Stickers
Resources:
You can find the assembly guide, code repository and further information for the Gert VGA 666 at the following links:
- This item is a Universal 12V 2A external switching power adapter.
- Power supply polarity : Inside positive outside negative,inside x(+) outside i(-).
- Input : 100-240V AC 50/60Hz
- Output : 12V 2A
- Cable length : 90 cm
- DC Plug Dimension : 5.5mm * 2.5mm
- Plug : EU Plug
1 x 12V 2A Power Adapter
- Input: AC100-240V 50/60Hz
- Output: DC 12V
- Shell Material: Aluminum
- Safety Compliance: CCC / CE /Rohs
- High price-effective, reliability with industry standards
- 100% full load burn-in test
- Universal AC input / full range
- It's good quality & high performance
- Cooling by free air convection.
- Not suggested for use in a bathroom
- Built-in over voltage, over current, and short circuit protection
- Working Temperature: 0~40℃
- Storage Temperature: -20~60℃
- Ambient Humidity: 0~95% Non-Condensation
Features
- Switch power supply, convert AC 110V/240V to 12V
- Wide input voltage range, steady and precise output voltage.
- Shortage protection, overload protection over voltage protection.
- Widely used as the power adapter for Led strip, LED display, billboard, industrial equipment, etc.
Please note: INDOOR USE ONLY!
Package includes
1 x 12V 5A power supply
This power supply is a isolated industrial grade built-in power module with temperature, over current, and short circuit protection.
Features:
AC85 - 264V or DC110 - 370V wide voltage input
DC 5V(+/ -0.2V) 600mA isolated output
Input Current: 0.0273A/115VAC 0.014A/230VAC
Input surge current: 20A (230VAC)
Frequency range: 50/60 Hz
Operating Temperature: -30 - 70 ℃
Relative humidity: 20%- 90%
Rated power: 3W
Output efficiency: 80%
Module size: 40mm x 23mm x 23mm
Package includes:
1 x AC-DC Isolated AC 110V / 220V To DC 5V 600mA Constant Voltage Switch Power Supply Converter
Sure, your flashing, chip-tune playing t-shirt is really cool at the party... but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you've even sewn a LilyPad slide switch in-line. Wouldn't it be nice if there was just a switch on the battery? Well look no further.
This LilyPad Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so you can shut off your project and save batteries. This slide switch is the same as is found on the LilyPad slide switch board, so it's not easy to accidentally turn off or on.
Just like the original Coin Cell Battery Holder, this simple board holds a 20mm coin cell battery (such as a CR2032) and gives you 4 connection points (two positive and two negative) for sewing into your project.
Package Includes:
1 x LilyPad Coin Cell Battery Holder CR2032 Battery Mount Module
A small, but mighty power supply. This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your LilyPad circuit. Good up to 200mA. Short circuit protected.
This board has AAA battery clips but can use an input from 1.2V to 5V.
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable - but be sure to remove the battery!
Package Includes
1 x LilyPad Power Supply Converter Module AAA Battery Step up to 5V
- Input: AC100-240V 50/60Hz
- Output: DC 12V
- Shell Material: Aluminum
- Safety Compliance: CCC / CE /Rohs
- High price-effective, reliability with industry standards
- 100% full load burn-in test
- Universal AC input / full range
- It's good quality & high performance
- Cooling by free air convection.
- Not suggested for use in a bathroom
- Built-in over voltage, over current, and short circuit protection
- Working Temperature: 0~40℃
- Storage Temperature: -20~60℃
- Ambient Humidity: 0~95% Non-Condensation
Features
- Switch power supply, convert AC 110V/240V to 12V
- Wide input voltage range, steady and precise output voltage.
- Shortage protection, overload protection over voltage protection.
- Widely used as the power adapter for Led strip, LED display, billboard, industrial equipment, etc.
Please note: INDOOR USE ONLY!
Package includes
1 x 12V 5A power supply
Shell Material: Metal case / Aluminum base
Protection: Shortage Protection, Overload Protection, Over Voltage Protection
Widely used in Industrial automation, LED display, communications, etc.
Safety Compliance: CCC/ FCC / CE
Working Temperature: 0~40℃
Storage Temperature: -20~60℃
Ambient Humidity: 0~95% Non-Condensation
IN-DOOR USE ONLY!
- Assumption: Your LED Strip has 60LEDs/m
- each LED 0.2W
- calculate max LED Strip Length: 0.2W/LED × 60LEDs/m=12W/m
- 30W(this listing)÷12W/m=2m
- So this unit will support a LED Strip(60LEDs/m, 0.2W/LED) Length (Max)=2m lights
Specifications:
| Type(Output Voltage,Output Current, Wattage) | Size | Intput Voltage |
| 5V 6A 30W | 110mm*78mm*35mm | 85-265V |
Package Includes:
1 x Power Supply For LED Strip