Search

Search Criteria

 
 
 
 

Products meeting the search criteria

Sort By:  
Temperature measurement range: -55°C ~ +125°C
R19.90  Inc VAT
Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R629.90  Inc VAT
Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R539.90  Inc VAT
Waterproof DS18B20 Digital temperature sensor + Resistor (Waterproof DS18B20 temp)

Description:

This is a pre-wired and waterproofed version of the DS18B20 sensor.  Handy for when you need to measure something far away, or in wet  conditions. While the sensor is good up to 125°C the cable is jacketed  in PVC so we suggest keeping it under 100°C. Because they are digital,  you don't get any signal degradation even over long distances! These  1-wire digital temperature sensors are fairly precise (±0.5°C over much  of the range) and can give up to 12 bits of precision from the onboard  digital-to-analog converter. They work great with any microcontroller  using a single digital pin, and you can even connect multiple ones to  the same pin, each one has a unique 64-bit ID burned in at the factory  to differentiate them. Usable with 3.0-5.0V systems.

The only  downside is they use the Dallas 1-Wire protocol, which is somewhat  complex, and requires a bunch of code to parse out the communication. If  you want something really simple, and you have an analog input pin,  the TMP36 is trivial to get going.

We toss in a 4.7k resistor, which is required as a pullup from the DATA to VCC line when using the sensor.

Specifications:

Cable specs:

  • Stainless steel tube 6mm diameter by 30mm long
  • Cable is 36" long / 91cm, 4mm diameter
  • Contains DS18B20 temperature sensor
  • If  your sensor has four wires - Red connects to 3-5V, Black connects to  ground and White is data. The copper wire is soldered to the wire  shielding
  • If your sensor has three wires - Red connects to 3-5V, Blue/Black connects to ground and Yellow/White is data

DS18B20 Technical specs:

  • Usable temperature range: -55 to 125°C (-67°F to +257°F)
  • 9 to 12 bit selectable resolution
  • Uses 1-Wire interface- requires only one digital pin for communication
  • Unique 64 bit ID burned into chip
  • Multiple sensors can share one pin
  • ±0.5°C Accuracy from -10°C to +85°C
  • Temperature-limit alarm system
  • Query time is less than 750ms
  • Usable with 3.0V to 5.5V power/data

Contents:

  • 1 x DS18B20 Digital temperature sensor
  • 1 x 4.7k resistor

Resources:

 

R44.90  Inc VAT
DHT11 Temperature and Relative Humidity Sensor Module (DHT11 temp/humid)

Description:

This module can detect humidity and temperature of the surrounding environment. Outputs a digital signal. Has a mounting hole for easy installation. Includes 3 DuPont wires to interface to microcontroller.

Specifications:

Humidity measurement range: 20%~90% RH
Humidity measurement error: ±5% RH
Temperature measurement range: 0~60 Cƒ
Working voltage: 5V
Size: 28 x 12 x 8mm

What's int the box?

1 x DHT11 Temperature and Relative Humidity Sensor Module

How to setup a DHT11 with your Raspberry Pi. The resistor is already on the PCB so you can skip the breadboard part

R59.90  Inc VAT
ANENG AN8002 Digital Multimeter AC/DC Current Voltage Frequency Resistance Temperature ℃/℉ (multimeter AN8002)
Description:
 
It is a Auto-ranging digital MultiMate using double-integral style A/D transform as the core. 
Can be used to measures Temperature AC/DC Voltage AC/DC Current Resistance Capacitance Diode and Continuity testing temperature Frequency and Etc.
The products are battery powered they are characterized by stable function and high reliability, with the features of overload protection and LCD display for clear reading are an ideal tools for lavatory radio fans and family use.
 
Features: 
 
Auto Range. 
True RMS measurement. 
Resistance capacitance frequency file high voltage 550V protection. 
Large screen display, the maximum of 6000 words. 
Sampling rate: about 3 times per second.
Temperature measuring.
Backlight display. 
Data retention. 
Polarity automatic recognition. 
Low voltage display. 
10A large current measurement MA level small current measurement Automatic shutdown. 
Main measurement: AC / DC voltage, AC / DC current, resistance, capacitance. 
Diode / off measurement, frequency and duty ratio measurement. 
 
Specification: 
 
 
FunctionRangeResolutionAccuracyMAX.ValueOther
DC Voltage 6.000V0.001V±(0.5%+3)1000VInput Resistance:10MΩ
60.00V0.01V
600.0V0.1V
1000V1V
60.00mV   0.01mV600mV
600.0mV    0.1mV   
AC Voltage 
 
6.000V0.001V±(1.0%+3)750VInput Resistance:10MΩ(600mV range, >60MΩ)
Frequency Response: 40Hz-1kHz
60.00V0.01V
600.0V0.1V
750V1V
60.00mV0.01mV   600mV
600.0mV    0.1mV   
DC Current
 
6.000A0.001A±(1.2%+3)10AMAX.Current:
10A(no more than 15 seconds)
No Voltage input at this mode
Frequency Response(AC):
 40Hz-1kHz
10.00A0.01A
60.00mA0.01mA600mA
600.0mA0.1mA
AC Current 
 
6.000A0.001A±(1.5%+3)10A
10.00A0.01A
60.00mA0.01mA600mA
600.0mA0.1mA
Resistance600.0Ω0.1Ω±(0.5%+3)60MΩNo Voltage input at this mode
6.000kΩ0.001kΩ
60.00kΩ0.01kΩ
600.0kΩ0.1kΩ
6.000MΩ0.001MΩ
60.00MΩ0.01MΩ±(1.5%+3)
Capacitance 9.999nF0.001nF±(5.0%+20)9.999mFNo Voltage input at this mode
99.99nF0.01nF±(2.0%+5)
999.9nF0.1nF
9.999μF0.001μF
99.99μF0.01μF
999.9μF0.1μF
9.999mF0.001mF±(5.0%+5)
Frequency99.99Hz0.01Hz±(0.1%+2)9.999MHz 
999.9Hz0.1Hz
9.999kHz0.001kHz
99.99kHz0.01kHz
999.9kHz0.1kHz
9.999MHz0.001MHz
Duty Cycle1%~99%0.1%±(0.1%+2)  
Diode√(DC forward current is 5mA, voltage is 3V)No Voltage input at this mode
Continuity√(no more than 50Ω)

Temperature
 
-20~1000℃1℃±(2.5%+5)1000℃ 
-4~1832℉1℉1832℉

Measurement mode: double-integral style A/D transform 
Sample rate: 3 times per second 
Over range indication: OL
Powered by 2 x AAA batteries  (Not included).
Working Environment: 0-40 degrees relative humidity: <80% 
Product size: approx. 130 x 65 x 30mm/5.11 x 2.55 x 1.18'' 
Net weight: approx. 170g 
Gross weight: approx.238g           
 
Package included:
 
1 x ANENG AN8002 Digital Ture RMS 6000 Counts Multimeter
2 x Test Lead Set 
1 x Temperature Sensing Cable 
1 x Storage Bag 
1 x English User Manual
R579.90  Inc VAT
DS18B20 Temperature Sensor TO-92 (DS18B20 Temperature Sensor)
Specification:

Temperature measurement range: -55°C ~ +125°C
Accuracy: ± 0.5°C
Encapsulation: TO-92

You will need a 4.7k resistor

Package includes:

1 x DS18B20

Adafruit's Raspberry Pi Lesson 11. DS18B20 Temperature Sensing

Temperature measurement range: -55°C ~ +125°C
R19.90  Inc VAT
MLX90614ESF AAA Non Contact Human Body Infrared IR Temperature Sensor (Infra red temp sensor)
The MLX90615 is an Infra Red thermometer for non contact temperature measurements. Both the IR sensitive
thermopile detector chip and the signal conditioning chip are integrated in the same TO-46 can package.
Thanks to its low noise amplifier, 16-bit ADC and powerful DSP unit, a high accuracy and resolution of the
thermometer is achieved. The thermometer is factory calibrated with the digital SMBus compatible

Features
  1.  Small size, low cost
  2.  Easy to integrate
  3.  Factory calibrated in wide temperature range: -40…85C for sensor temperature and -40…115C for object temperature
  4.  High accuracy of 0.5C over wide temperature range (0...+50C for both TA and TO )
  5.  High (medical) accuracy calibration
  6.  Measurement resolution of 0.02C
  7.  SMBus compatible digital interface
  8.  Power saving mode
  9.  Customizable PWM output for continuous reading
  10.  Embedded emissivity compensation
  11.  3V supply voltage

Datasheets available at https://github.com/arduinolearning/Datasheets/blob/master/MLX90614.pdf
R529.90  Inc VAT
MS Weather Station wireless rain meter w/ thermometer, rain gauge Weather Station for in/out temperature (Rain weather station)
Details:

1).Outdoor wireless sensor (range up to 100 meter)
2) Detail display of rainfall data in 1hour, 24hour, week, month
   and total since last reset(user selectable in inch or mm) 
3) Indoor  and outdoor temperature (°F to °C)
4) Time and date with manual setting option 
5) 12 /24 hour time mode 
6) Calendar 
7) Time zone setting 
9)Time alarm    
9) Free standing

Specifications:
1) Rainfall display range: 0 to 19,999mm
2) Outdoor temperature range: -40 ~ +65°C (-40°F to +149°F)
3) Indoor temperature range: -9.9 ~ +60°C (-15.8°F to +176°F)
4) Temperature accuracy: ±1.0°C5) Power requirements:
  a) Receiver: 2 x "AA" alkaline batteries (not included)
 
b) Rain gauge: 2 x "AAA" alkaline batteries (not included)
5)Transmission range: up to 100meters( 330feet)
6) Transmission frequency: 433MHz


Package includes:
1 x Rain Gauge
1 x Receiver
1 x User Manual
2 x Screws

R839.90  Inc VAT
BME280 1.8-5V High Precision Atmospheric Pressure, Temperature, humidity Sensor Module (BME280 pressure temp humid)
BME280, the precision sensor from , is soldered onto PCB.
Not only the pressure and the temperature, this sensor can measure humidity.
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface
 

    Specifications:

    Supply Voltage: 1.8 - 5V DC
    Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
    Operational Range:
    Temperature: -40 to +85°C
    Humidity: 0-100%
    Pressure: 300-1100 hPa
    Temperature: 0.01°C
    Humidity: 0.008%
    Pressure: 0.18Pa
    Accuracy:
    Temperature: +-1°C
    Humidity: +-3%
    Pressure: +-1Pa
    I2C address
    SDO LOW : 0x76
    SDO HIGH: 0x77

What's in the box?

1 x bme280 sensor
1 x header


The Raspberry Pi Foundation Project
R289.90  Inc VAT
RPICT3T1 30 Amp Raspberrypi 3x Current Sensor Adaptor 1 x temperature (lec 30A 3 current 1 temp board)

RPICT3T1

Please note: Raspberry Pi and sensors are NOT INCLUDED

Raspberrypi AC current hat with temperature


Online Documentation




  • 3x AC Current Ports.
  • 1x Temperature Ports.
  • Provides Irms, EstimatedPower, Temperature.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.

Package Content

  • 1 RPICT3T1 Unit.
  • 2 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Temperature:

Current Sensor:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

MicrocontrolerAtmel Attiny84
MCU Frequency8Mhz
Operating Voltage3.3V
Waveform Sampling2500sps
Fastest Data Polling600ms
Vertical Resolution10 bits (1024 steps)
CommunicationUART Serial Port
FirmwareArduino (open source)
Dimensions56x35mm
Programming port6 pin ISP
Compatible OSAny supporting GPIO serial port access
Compatible RaspberrypiAll of Family 1,2,3,4 and Model A, B
Compatible CTCurrent output type
AC Current Range30A
Max Temperature probes8
Smallest Readable CurrentApprox 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R629.90  Inc VAT
RPICT3T1 100 Amp Raspberrypi 3x Current Sensor Adaptor 1 x temperature (lec 100A 3 current 1 temp board)

RPICT3T1

Please note: Raspberry Pi and sensors are NOT INCLUDED

Raspberrypi AC current hat with temperature


Online Documentation




  • 3x AC Current Ports.
  • 1x Temperature Ports.
  • Provides Irms, EstimatedPower, Temperature.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.

Package Content

  • 1 RPICT3T1 Unit.
  • 2 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Temperature:

Current Sensor:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

MicrocontrolerAtmel Attiny84
MCU Frequency8Mhz
Operating Voltage3.3V
Waveform Sampling2500sps
Fastest Data Polling600ms
Vertical Resolution10 bits (1024 steps)
CommunicationUART Serial Port
FirmwareArduino (open source)
Dimensions56x35mm
Programming port6 pin ISP
Compatible OSAny supporting GPIO serial port access
Compatible RaspberrypiAll of Family 1,2,3,4 and Model A, B
Compatible CTCurrent output type
AC Current Range100A
Max Temperature probes8
Smallest Readable CurrentApprox 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Connect up to 3 Current and 1 temperature sensor to a raspberry pi.
R539.90  Inc VAT
RPIZ_CT3T1 3 current and 1 Temperature 30A AC adapter for Raspberry Pi zero (lec zero 3 current 1 temp)

The RPIZ_CT3T1 is the same unit as the RPICT3T1 in the Raspberry pi Zero format.

Refer to the RPICT3T1 for full documentation.

Use with sct-013-000 split core current sensor and DS18B20 temp sensor

Please note: Raspberry Pi Zero and sensors are not included


R649.90  Inc VAT
Wemos® Higrow ESP32 WiFi + bluetooth Battery + DHT11 Soil Temperature And Humidity Sensor Module (Wemos Higrow)
Description:
 
More details available at:https://github.com/LilyGO/higrowopen


A LG 3000mAH 18650 battery could make ESP32 run 17 hours or more.
This capacitive soil moisture sensor differs from most of the resistive sensors on the market, using capacitive sensing principle to detect soil moisture. It avoids the problem that the resistance sensor is easy to corrode and greatly prolongs its working life.
Size: 193.5mm x 29.4mm
 
Package includes:
 
1 x Wemos® Higrow ESP32 WiFi + bluetooth Battery + DHT11 Soil Temperature And Humidity Sensor Module
R389.90  Inc VAT
Interior Panel Mount Temperature Meter - Celsius (Temp panel mount)
Features

Material: Plastic
Indoor temperature °C display.
It comes with a mounting clips which allows it to be panel mounted
Temperature range: -50 ~ + 70 Degrees.
Usage temperature: -10 ~ +50 Degrees.
Usage humidity:5% ~ 80%
Accuracy:+/-01 Degrees.
Distinguishing temperature: 0.1 Degrees.
Power: 2 x DC1.5V AG13 button batteries (Not included)
Cable length:0.8M.
Size:48 x 28 x 15(mm)
Color:Black


Package Includes:

1 x LCD Digital Thermometer Temperature Sensor
R49.90  Inc VAT
PWM Controlled Fan HAT for Raspberry Pi I2C Temperature Monitor (WS fan hat)
Designed for Raspberry Pi series

Standard Raspberry Pi 40PIN GPIO header, customized for Raspberry Pi series boards


Features at a glance
  • PCA9685 PWM driver as the fan controller, powerful driving capability, auto PWM adjustment
  • 0.91" OLED, 128x32 pixels, displays board temperature or other user-defined content in real time
  • Adopts 3007 size PWM controlled fan, up to 8000rpm speed, brings strong airflow
  • Supports retrieving temperature data in real time, and then adjusting the speed automatically, programmable configuration
  • I2C pins, for connecting other host control boards
  • 16-ch PWM outputs, for driving other external PWM devices
  • Comes with heat sinks, better cooling effect

PCA9685 Fan Controller

Up to 16-ch PWM outputs, powerful driving capability, auto PWM adjustment combined with the included heat sinks, achieving better cooling effect


0.91" OLED mini display
  • 128×32 pixels, I2C controlled
  • displays board temperature or other user-defined content in real time


What's On Board


  1. Standard Raspberry Pi 40PIN GPIO header
  2. PCA9685 PWM driver
  3. 3007 size PWM controlled adjustable fan
  4. PCA9685 I2C address configuration
  1. Reserved I2C control pins
  2. Reserved PCA9685 output channels
  3. 0.91" OLED display



Pinout definition


Outline dimensions(mm)


Resources & Services





R279.90  Inc VAT
Hygrometer Thermometer Digital LCD Temperature Humidity Meter 10%~99%RH (Hygrometer Thermometer)
Description:

Color: Black
Measuring humidity: 10%RH-99%RH
Humidity accuracy: 5%
Humidity display resolution: 1% RH
Measuring temperature range: -50 centigrade~+70 centigrade
Temperature accuracy: 1 centigrade
Temperature display resolution: 0.1centigrade .
Operating voltage: 2 x 1.5V button LR44 batteries (Not included)
Dimension: 4.7x2.8x1.5cm(approx.)
LCD dimension: 3.6x1.7cm(approx.)
High Quality Hygrometer, wonderful tools for Indoor, Outdoor, Home, Laboratory, Library..etc.


Package includes:

1 x Humidity Hygrometer Meter
R79.90  Inc VAT
SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor Real Time Low-battery notification Works with SONOFF ZigBee Bridge eWeLink APP (zigbee SNZB-02)

Note 1: Batteries not included - ( 3V CR2450)
Note 2: SNZB-02 must be used with the Zigbee Bridge.

SONOFF SNZB-02 is a ZigBee temperature and humidity sensor that can seamlessly work with SONOFF ZigBee Bridge to track and record the temperature and humidity change in your home, which all real-time readings can be checked on eWeLink APP. Better still, you can set a condition in the smart scene that is the fan is turn on/off when the temperature reaches the limit value, or the dehumidifier in your room starts working once the humidity is over higher, helping prevent the growth of mildew and allergens. You can set a smart scene to trigger alerts through events like high/low temperature, high/low humidity conditions and more.

Device sharing function makes your kids, family, and even the neighbors informed about the environmental conditions of your home with their mobile phones.

It is a battery-operated sensor that can be placed in any corner of your house to monitor the room temperature and humidity. Installation without any tool, simply stick the sensor on the surface of the wall or device and see it nicely to work for you!

1. Do not install on a metal surface, it will affect the wireless communication distance.
2. Installation height of less than 2 m is recommended.
3. The device can be operated intelligently via working with the SONOFF ZigBee Bridge to communicate with other devices.

SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor Overview

Features:
Monitor indoor temperature and humidity.
Sync the real-time temperature and humidity recordings to APP.
Can trigger Wi-Fi devices in smart scene.
Add a camera to ensure you know any emergency in your home.
Low-battery notification.
Quick and easy to install.

Specifications:
Battery: 3V(CR2450)
Wireless protocol: Zigbee (IEEE 802.15.4)
Dimensions: 43mm x 43mm x 14mm

What's in the box
1 x SONOFF SNZB-02 ZigBee Temperature And Humidity Sensor

R239.90  Inc VAT
Grove - Temperature Sensor (Grove temp sensor)

Grove - Temperature Sensor uses a thermistor to measure ambient temperature. The resistance of thermistor changes based on ambient temperature. This resistance value alters the output of a voltage divider which is measured by an analog input pin and converted to a temperature value. The operating range is -40 to 125°C , with an accuracy of 1.5°C.

For all Grove users (especially beginners), we provide you guidance PDF documents. Please download and read through Preface - Getting Started and Introduction to Grove before your use of the product.

Ready to use with microcontrollers as a digital input. This product also has a compact modular design Plug-and-play grove compatible interface.

Based on the picture above, the grove shield for Arduino is stacked with Seeeduino V4.2. Of course you can use that shield with Arduino board too :)

You can get grove HAT for Raspberry Pi and the Maker Pico board

Features and specifications:

  • Grove compatible interface
  • Arduino library ready
  • Operating voltage: 3.3~5V
  • Zero power resistance: 100 KΩ
  • Resistance Tolerance: ±1%
  • Thermistor: NCP18WF104F03RC (NTC)
  • Nominal B-Constant: 4250 ~ 4299K
  • Operating temperature range: -40°C to 125°C
  • Temperature Accuracy: ± 1.5°C

Packing List:

  • 1 x Grove - Temperature Sensor
  • Grove 4 Pin Buckled 20cm Cable

Resources:

R89.90  Inc VAT
ATTEN ST-2065D EU Plug 65W 220V with Digital LCD Display Temperature Adjustable Soldering Iron (Atten ST-2065D soldering iron)
Description:

  • Automatically sleep after 10 minutes.
  • Automatically shut down after 20 minutes.
  • Temperature reach 480°C in 1 minute.Build in PID system equipped.
  • 9 shortcut range to adjust temperature by button
  • Products use LCD display


Specifications:

  • Voltage: AC220V
  • Temperature range:250~480°C
  • Temperature stability:±1°C
  • Temperature offset range:±10°C
  • Temperature Unit:°C/℉
  • Heater: Four-core PTC ceramic heater
  • Power - Model Number:65W -ST-2065D
  • Colour:black
  • Material:ABS+ metal
  • Size:25*2*3cm


What's in the box?

1 x ATTEN ST-2065D Soldering Iron
R699.90  Inc VAT
ATTEN ST-8800D heat gun adjustable temperature and air volume anti-static Hot Air Station (Atten hot air station)
Description:

1.Large LCD screen;Temp/Airadjust easily.
2.Touch sensor inside,auto sleep function will take effec twhen hot air gun placed on the stand.
3.Use brushless vortex fan making cyclone air output more gentle and evenly.(Offer 4 nozzles)
4.It has automatic large air volume cooling function,effectively protect the life of heating core and handle.
5.It has independent cold air function, can deal with special use purpose.
6.Three sets of quick temperature keys,can be set and save independently, use easily
7.It has password protection and key lock function, control easily.
8.With timing function and temperature compensation function,make use flexibly.

Specifications:



What's in the box?

1 x Atten hot air gun
R2,699.90  Inc VAT
30Mx15mm Heat Resistant High Temperature Insulation Electronics Polyimide Kapton Tape (Kapton tape 15mm)
Application:

  • High temperature masking tape
  • Frequency conversion power supply in the electronics industry. Also use as perfect heat resistance ribbon on 3d printing, powder coating, etc
  • PCB protection during wave soldering
  • Insulation on transformers, motors and coils
  • Fiber Optic Cables
  • Solar panels

Specifications:

  • 100% new and high quality
  • Material: Polyimide
  • Color: Brown Metallic
  • Width: 3/5/8/10/15/20/25/30/35 / 40mm
  • Length: 30 M
  • Long term temperature: 260 ° C degrees
  • Short term temperature: 300 ° c.

What's in the box?

1 x 15mm Kapton Tape
R87.90  Inc VAT
AM2302 DHT22 Temperature And Humidity Sensor Module (DHT22 temp/humid)

Features:

AM2302 Humicap digital temperature and humidity module is a digital output signal containing a calibrated temperature and humidity combined sensor. It uses dedicated digital module capture technology and temperature and humidity sensor technology to ensure that products has high reliability and excellent long-term stability. Sensor includes a capacitive humidity sensing element and a high-precision temperature measurement device, and with a high-performance 8-bit microcontroller connected. Therefore, the product has excellent quality, fast response, anti-interference ability, low cost and other advantages. Ultra-small size, low power consumption, signal transmission distance up to 20 meters. Making it the best choice for all kinds of applications and even the most demanding applications.

Applications:

HVAC (Heating Ventilation Air Conditioning), dehumidifiers, testing and inspection equipment, consumer goods, automotive, automation, data loggers, home appliances, humidity regulator, medical,weather stations, and other related humidity detection control.

Specification:

Dimensions: 40 x 23mm
Weight: 4g
Voltage: 5V
Port: digital two-way single bus
Temperature range: -40 to 80 °C ± 0.5 °C
Humidity: 20 to 90% RH ± 2% RH
Platform: Arduino, SBC

Package includes:

1 x Sensor Module


How to setup a DHT22 with your Raspberry Pi.The resistor is already on the PCB so you can skip the breadboard part.

R129.90  Inc VAT
Per Page      1 - 20 of 20
  • 1