WaveShare
The Pico-Eval-Board is an overall evaluation solution designed for Raspberry Pi Pico.
The Pico-Eval-Board is an overall evaluation solution designed for Raspberry Pi Pico. With 3.5inch 65K colorful LCD display and misc helpful onboard components, this evaluation board allows you to try almost every on-chip peripheral of the RP2040, eliminating the messy wiring. It is an ideal choice for users to fast get started with the Raspberry Pi Pico, as well as the RP2040 chip.
Specifications
- Operating voltage: 5V
- Touch Type: Resistive
- Communication bus: SPI
- Display panel: IPS
- Controller: ILI9488/XPT2046
- Resolution: 480×320 Pixels
- Display colors: 65K colorful
- Pixel size: 0.153 × 0.153 mm
- Display size: 73.44 × 48.96 mm
- Dimensions: 86.00 × 57.20 mm
Features
- Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards
- 3.5inch resistive touch screen, 65K colorful, bringing clear and vivid display effect
- Standard 3.5mm audio jack, for headphone or other audio peripherals
- Micro SD card slot through the SDIO interface, faster access speed than SPI interface
- Integrates battery header and recharge circuit, allows it keep running without wired power supply
- Other rich resources like buzzer, photoresistor, and RGB LED.
- Comes with development resources and manual (Raspberry Pi Pico C/C and MicroPython examples)
What's in the box?
1 x Overall Evaluation Board for Raspberry Pi Pico
Resources
Wiki for Evaluation Board for Raspberry Pi Pico
With 3.5inch 65K colorful LCD display and misc helpful onboard components, this evaluation board allows you to try almost every on chip peripheral of the RP2040, eliminating the mess wiring.
It is an ideal choice for user to fast get started with the Raspberry Pi Pico, as well as the RP2040 chip.


Specifications
- Product: MG996R Servo
- Torque: 9kg/cm(4.8V), 11kg/cm(6V)
- Speed: 0.19s/60°(4.8V), 0.18s/60°(6V)
- Rotate angle: 180°
- Operating voltage: 4.8 ~ 6V
- Gear: metal
- Dead band: 5us
- Weight: 55g
- Dimension: 40.7mm × 19.7mm × 42.9mm

What's in the box?
1 x MG996R Servo with Arm kit
Embedded Protections: Power Supply Isolation & Photocoupler Isolation
Features
- Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal
- Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay
- High quality relay, contact rating: 10A 250V AC or ≤10A 30V DC
- ABS protection enclosure with rail-mount support, easy to install, safe to use
- Breakout USB port and BOOT pin, make it easy to debug without disassembling the enclosure
- PWR indicator, RGB LED, and passive buzzer outside the enclosure
- Comes with development resources and manual (Raspberry Pi Pico C/C and MicroPython examples)
Specifications
- OPERATING VOLTAGE: 5V
- RELAY CHANNEL: 8 ch
- COMMUNICATION PROTOCOL: USB
- CONTACT FORM: 1NO 1NC
- COMMUNICATION INTERFACE: Micro USB
What's in the box?
- ABS protection enclosure (top and bottom) x1
- Pico-Relay-B x1
- Screwdriver x1
- Screws pack x1


- Raspberry Pi Pico header
- Relay screw terminal
for connecting external devices - Power supply screw terminal
the multi relays are connected in parallel - Pogo pins
- USB communication port
connected via pogo pins - BOOT key
connected via pogo pins - Reset key
Pico reset - Passive buzzer
controllable sound frequency
- Power indicator
- WS2812
RGB LED, cool! - 8-channel quality relays
contact rating per channel: ≤10A 250V AC or ≤10A 30V DC - Relay operating indicator
- Photocoupler isolation
prevent interference from external high-voltage circuit connected to the relay - Power supply isolation
provides stable isolated voltage, needs no extra power supply for the isolated terminal - Thickened tracks
allows large current devices

Outline dimensions

What's in the box?
1 x Pico 8-Channel relay module
Resources
WIKI: Pico-Relay-B
Note: We have tested this unit successfully on Zero and Zero 2.
The ETH/USB HUB HAT (B) is an Ethernet and USB HUB designed for Raspberry Pi, providing 1x RJ45 Ethernet port and 3x USB 2.0 ports. It's pogo pin design is specialized for Zero series, while the onboard normal USB connector can be used to connect with other Raspberry Pi boards through a USB cable.
Specifications
- 3x extended USB ports, compatible with USB 2.0 / 1.1
- Incorporates RTL8152B Ethernet chip, supports 1x RJ45 Ethernet port, 10/100M auto-negotiation
- Pogo pin design, for direct connecting with Raspberry Pi Zero/Zero W/Zero WH
- USB HUB connector, for connecting with Raspberry Pi 4B/3B /3A /2B through USB cable
What's in the box ?
1 x ETH/USB HUB HAT (B)
1 x Screws and standoffs pack
Resources
Wiki: ETH/USB_HUB_HAT_(B)




Supports Pi 4B/3B+/3A+/3B/2B/B+/A+, CM3/3+/4*

Device & System Support
Supports Ubuntu / Kali, single point touch, driver free
Supports Retropie, driver free

Touch Control

up to 5-points touch, depending on the operating system.

Appearance and Dimensions

What's in the box?
1 x 7inch DSI LCD
2 x FPC 15PIN 1.0 pitch 50mm (opposite sides)
1 x PH2.0 2PIN wire 10cm
1 x Screws pack
Resources
- Designed for Raspberry Pi series, compatible with Raspberry Pi 3 / 3B / 4B, etc.
- I2C bus communication, monitoring the batteries voltage, current, power, and remaining capacity in real time
- Multi battery protection circuits: over charge/discharge protection, over current protection, short circuit protection, and reverse protection, along with the equalizing charge feature, more safe and stable
- Onboard 5V regulator, up to 5A continuous output current, more sufficient power source for Raspberry Pi
- 5V USB output, convenient for powering other boards
- Batteries warning indicators, easy to check if the battery is connected correctly
- Comes with development resources and manual
Specifications
- OUTPUT VOLTAGE: 5V
- CHARGER: 8.4V 2A
- CONTROL BUS: I2C
- DIMENSIONS: 56 × 85mm
- BATTERY SUPPORT: 2x 18650 Li batteries(NOT included)
- MOUNTING HOLE SIZE: 3.0mm





(** Raspberry Pi, Cables are for reference ONLY, the Raspberry Pi, cables and Fan HAT are NOT included.)


What's in the box ?
1 x UPS Hat (B)
1 x 8.4v Battery Charger
1 x Acrylic protection panel
1 x Screws pack
- The 18650 batteries are NOT included
- Please note that the battery length SHOULD be less than 67mm, some batteries with protection plate in the market are NOT supported, learn more.
Resources
WIKI: UPS_HAT_(B)
Need batteries? You will find our battery selection here
The Capacitive Fingerprint Reader (B) is a fast and stable capacitive fingerprint module specialized for secondary development, suits integration applications.
By incorporating high performance Cortex core processor, high security commercial fingerprint algorithm, and advanced semiconductor fingerprint sensor, this module is designed as a intelligent integration module with functions including fingerprint enrolling, image processing, template generating and storing, fingerprint matching and searching, etc.
- Easy to use by some simple commands, you don't have to know any fingerprint technology, or the module inter structure/calculation
- Commercial fingerprinting algorithm, stable performance, fast identification
- Sensitive detection, just touch the collecting window lightly, without pressing
- Allows to freely input/output fingerprint images, fingerprint feature file and other fingerprinting actions
- Dual communication, UART or USB
- Comes with rich development resources (related command documents, tools, and examples for Raspberry Pi/Arduino/STM32)
parameter | value |
---|---|
Sensor | Semiconductor (capacitive) |
Module dimension | 34 × 28.5mm |
Sensor dimension | 33.4 × 20.4mm |
Image | DPI 508 |
Image resolution | 208 × 288 |
Greyscale | 256 (8-bit) |
Sensing area | 14.6 × 10.6mm |
Fingerprint capacity | 3000 |
Security level | 1-5 configurable, 3 by default the higher value, the lower FAR (False Acceptance Rate), yet the higher FRR (False Rejection Rate) |
Encryption key | 64-bit encryption |
Image collecting rate | 20fps |
Matching time | 0.5s |
Dynamic current | <40mA |
Operating voltage | 3.3-5V |
Communication port | UART or USB |
ESD | SD IEC 61000-4-2 LEVEL 4 positive/negative 15KV air discharge |
Baudrate | configurable: 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600bps 115200bps by default |
Outline dimensions

What's in the box?
1 x Capacitive Fingerprint Reader (B)
1 x PH2.0 5PIN wire
Resources
Special Angled Header, Let The Adapter Stand At A Comfort Angle,
Make It More Convenient To Use With HATs Like SPI/DPI Display
Dimensions
What's in the box ?
1 x PI400/500 GPIO Leaning adapter
By utilizing the new generation LoRa spread spectrum modulation technology, the communication distance of the module is as long as 5km, also supports auto repeating to transmit longer. Other features include Wake on Radio, wireless config, carrier sensing, communication key, and so on.
Comparing with normal LoRa modules, the SX1262 LoRa HAT achieves longer communication distance, higher rate, lower consumption, better safety and anti-interference. It is suitable for various applications such as industrial control, smart home, data collection, etc.
Features
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
- Onboard CP2102 USB TO UART converter, for serial debugging
- Brings the UART control interface, for connecting host boards like Arduino/STM32
- 4x LED indicators, easy to check the module status
- LoRa spread spectrum modulation technology, up to 81 available signal channel, longer communication distance, more robust to interference
- Auto multi-level repeating, suit for ultra long range communication, allows multi network on the same region
- Low power consumption features like deep sleeping and Wake on Radio, ideal for battery-powered applications
- Customizable communication key which won't be retrieved, greatly improves the security of user data
- Supports LBT, monitoring the signal channel noise before transmitting, greatly improves the success ratio under extreme environment
- Supports RSSI signal intensity indicating, for evaluating signal quality, tuning the network
- Supports wireless parameter configuration, by sending wireless command/data packet, remotely configure or retrieve the module parameter
- Supports fixed-point transmission, broadcast, signal channel monitor
- Comes with development resources and manual (examples for Raspberry Pi/STM32)
What's on Board?

- SX1262 LoRa module
- 74HC125V: voltage level translator
- CP2102: USB TO UART converter
- Raspberry Pi GPIO connector: for connecting with Raspberry Pi
- USB TO UART port
- UART header: for connecting host boards like STM32/Arduino
- SMA antenna connector
- IPEX antenna connector
- Indicators:
- RXD/TXD: UART RX/TX indicator
- AUX: auxiliary indicator
- PWR: power indicator
- UART selection jumpers
- A: control the LoRa module through USB TO UART
- B: control the LoRa module through Raspberry Pi
- C: access Raspberry Pi through USB TO UART
- LoRa mode selection jumpers
- short M0, short M1: transmission mode
- short M0, open M1: configuration mode
- open M0, short M1: WOR mode
- open M0, open M1: deep sleep mode
Dimensions

What's in the box ?
1 x SX1262 868M LoRa HAT
1 x USB type A plug to micro plug cable
1 x 868MHz antenna
Resources
Wiki : www.waveshare.com/wiki/SX1262_868M_LoRa_HAT
Industrial 6-ch Relay Module for Raspberry Pi Zero, RS485/CAN, Isolated Protections, Tailored For Raspberry Pi Zero Series also Suitable For Raspberry Pi Zero With Pre-Soldered Pin header.
Features
- RS485 half-duplex communication: using SP3485, UART control, auto RX/TX switch
- CAN half-duplex communication: using MCP2515 SN65HVD230 solution, SPI control
- Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal
- Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay
- Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic
- Onboard resettable fuses and protection diodes, ensuring current/voltage stable output, preventing over current/voltage, better shock-resistance performance
- High quality relay, contact rating: ≤10A 250V AC or ≤10A 30V DC
- ABS protection enclosure with rail-mount support, easy to install, safe to use
- Comes with development resources and manual (wiringPi and python examples)
Specifications
OPERATING VOLTAGE | 7V~36V (industrial input voltage compatible) | RELAY CHANNEL | 6 ch |
---|---|---|---|
COMMUNICATION PROTOCOL | RS485, CAN | CONTACT FORM | 1NO 1NC |
What's in the box?
1 x ABS protection enclosure (top and bottom)
1 x RPi Zero Relay
1 x Screwdriver
1 x 12V 1A power adapter
1 x Screws pack
Resources
WIKI: RPi_Zero_Relay
1024×600, 7-inch Capacitive Touch Screen LCD, HDMI interface, supports various systems. Toughened glass capacitive touch panel, 6H hardness. It supports Raspberry Pi and can also be used as a computer monitor.
Features
- 7inch IPS screen, 1024x600 hardware resolution, configurable by software. (up to 1920x1080)
- Toughened glass capacitive touch panel, 6H hardness. (case version only)
- Supports popular mini PC such as Raspberry Pi, BB Black, Banana Pi.
- Used with Raspberry Pi, supports Raspbian, Ubuntu, driver free.
- Multi-languages OSD menu, for power management, brightness/contrast adjustment, etc.
- It has a 3.5mm audio jack and supports HDMI audio output
- Supports VGA input (specific cable is required and should be purchase separately)
- High-quality PC case, optional tilt angle: 30°/50°.







What's in the box ?
1 x 7inch HDMI LCD (H)
1 x HDMI cable
1 x HDMI to Micro HDMI Adapter
1 x USB type A plug to micro B plug cable
1 x RPi screws pack (4pcs)
1 x Quick start sheet
Resources
( Calibration for touch, Working with Windows, Raspberry Pi , Jetson Nano etc.)
Wiki: www.waveshare.com/wiki/7inch_HDMI_LCD_(H)

Features at a glance
- Incorporates original chip Si3404, high-efficiency, high-safety, stable-performance
- 10/100/1000Mbps auto-negotiation Ethernet port
- 802.3af/at-compliant PoE (Power over Ethernet) standard
- Isolated SMPS (Switching Mode Power Supply), effectively protecting the powered device
- 5V DC output, suitable for powering Raspberry Pi and other small-scale network devices
- Black dull-polish metal case, sturdy and rugged, higher protection level, better heat dissipation
Specifications
Power supply | supports 1/2(+); 3/6(-); 4/5(+); 7/8(-) powering |
---|---|
PoE input voltage | 37V ~ 57V |
Type-C output | 5V 2.5A (MAX) |
Cable | Cat-5 UTP |
Standard | IEEE 802.3 af/at PoE Ethernet |
Data rate | 10/100/1000Mbps |
LED indicator | PoE power input indicator |
Dimensions | 86 × 30 × 25mm (l × w × h) |
Operating temperature | -40℃ ~ 85℃ |
Original chip solution
Incorporates Si3404, high-integration, high-efficiency, more safe and reliable

Isolated circuit protection, effectively protecting the powered device
Industrial grade protection case
aluminum alloy case, sturdy and rugged, higher protection level, better heat dissipation
Powering the Raspberry Pi or other 5V-powered network devices by PoE switch

for reference ONLY, Raspberry Pi and switch are NOT included.
This is an E-Ink display HAT for Raspberry Pi, 2.7inch, 264x176 resolution, with embedded controller, communicating via SPI interface.
Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.
Features- No backlight, keeps displaying last content for a long time even when power down
- Ultra low power consumption, basically power is only required for refreshing
- Compatible with Raspberry Pi 2B/3B/Zero/Zero W
- Onboard 4x Keys
- SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
- Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)
Specifications
- Operating voltage: 3.3V
- Interface: 3-wire SPI, 4-wire SPI
- Outline dimension: 85mm × 56mm
- Display size: 57.288mm × 38.192mm
- Dot pitch: 0.217 × 0.217
- Resolution: 264 × 176
- Display color: black, white
- Grey level: 2
- Full refresh time: 6s
- Refresh power: 24mW(typ.)
- Standby power: <0.017mW
- Viewing angle: >170°
Interface
SYMBOL | DESCRIPTION |
---|---|
VCC | 3.3V |
GND | Ground |
DIN | SPI MOSI pin |
CLK | SPI SCK pin |
CS | SPI chip selection, low active |
DC | Data/Command selection (high for data, low for command) |
RST | External reset, low active |
BUSY | Busy status output, low active |
What's in the box?
2 x RPi screws pack (2pcs)
Resources
Features at a glance
- Original FT232RL onboard
- Supports Mac OS, Linux, Android, WinCE, Windows 7/8/8.1/10/11...
- 3x VCCIO power mode via jumper setting:
- - VCCIO - 5V: 5V output
- - VCCIO - 3.3V: 3.3V output
- - open the jumper: powered from target board (3.3V-5V)
- 3x LED indicators: TXD, RXD, PWR
- Pins accessible on pinheaders: TXD, RXD, RTS#, CTS#
- Other pins are accessible on drilled holes, easily connected to user application system (the pin pitch is compatible with universal prototype board)
FT232 solution

- VCCIO ↔ 3.3V or 5V output (the module is powered from USB, and the onboard jumper should be shorted to 3.3V or 5V)
- GND ↔ GND
- TXD ↔ MCU.RX (signal direction: MCU.RX << FT232 << PC.TX)
- RXD ↔ MCU.TX (signal direction: MCU.TX >> FT232 >> PC.RX)
- RTS ↔ MCU.CTS (signal direction: MCU.CTS << FT232 << PC.RTS)
- CTS ↔ MCU.RTS (signal direction: MCU.RTS >> FT232 >> PC.CTS)
Outline Dimensions
PoE Ethernet / USB HUB BOX for Zero. Dull polish surface, well designed, nice & dust-proof. PoE 802.3af-compliant Ethernet Port | 3x USB 2.0 Ports.
Features at a glance
The PoE-ETH-USB-HUB-BOX is a HUB kit with PoE/ETH/USB HUB HAT inside. It is tailored for Raspberry Pi Zero series, small in size, each cut-out of the case is exactly aligned with the connector. The case adopts classic Raspberry Pi red/white color combination, with quality dull polish surface, effectively keeping the Zero away from dust. By using this small HUB BOX and some proper 802.3af-compliant power sourcing equipments, it is possible to provide both network connection and power supply for your Raspberry Pi Zero in only one Ethernet cable, along with 3x extended USB ports.
- Designed for Raspberry Pi Zero, compatible with Zero series boards
- Incorporates RTL8152B Ethernet chip, with 10M / 100M auto-negotiation RJ45 port
- PoE (Power over Ethernet) feature, 802.3af-compliant
- Fully isolated SMPS (Switch Mode Power Supply)
- 3x extended USB ports, compatible with USB 2.0 / 1.1
- Angle rounded design, smooth hand feeling, "simple snap" case lid
- Quality ABS material, dull polish surface, anti-fingerprint
- Comes with two different lids, changing as you like
Specifications
- PoE power input: 37V ~ 57V DC in
- Power output: 5V 2.5A DC out
- Network standard: IEEE 802.3af-compliant PoE
- Dimensions: 72.80 × 37.50 × 45.80 mm
Compatible with Raspberry Pi Zero series
specialized pogo pin connection, dedicated cut-outs for Zero series, plug-and-play
USB1 ~ USB3, compatible with USB 2.0 / 1.1

USB to Ethernet conversion by the RTL8152B chip, 10M / 100M auto-negotiation

"simple snap" design, easy to change, allows attaching other Zero HATs

Application example

Outline dimensions


What's in the box?
1 x PoE/ETH/USB HUB HAT kit (1)
1 x ABS case (2)
1 x Rubber feet 4PCS (3)
1 x Screws pack (4)
Resources
- Incorporates character LCD panel LCD1602
- Adjustable RGB backlight color, up to 16M (2563) backlight colors in theory
- I2C control interface, only two signal pins are required, saving the IO resource
- Compatible with 3.3V/5V operating voltage
- Comes with development resources and manual (Raspberry Pi/Jetson Nano/Arduino examples)
Specifications
- Operating voltage: 3.3 ~ 5V
- LCD controller: AiP31068
- Communication Interface: I2C
- RGB driver: PCA9633
- Display Panel: character LCD
- Display size:64.5 × 16.0mm
- Characters: 16 × 2
- Dimensions: 87.0 × 32.0 × 13.0mm
- Backlight colours: 16M
- Operating voltage: -20 ~ 70℃
Adjustable RGB backlight color - up to 16M colors available

for connecting with host boards like Raspberry Pi / Arduino...

VCC | 3.3V ~ 5V power input |
GND | GND |
SCL | I2C clock pin |
SDA | I2C data pin |
Hardware connection
connecting with Raspberry Pi Pico

connecting with Raspberry Pi

connecting with Arduino board

connecting with Jetson Nano Developer Kit




8-50mm adjustable focal length, flexible photo composition at your will

Adjustable focal length



- Raspberry Pi, and High Quality Camera in the photos are NOT included
- To use with Raspberry Pi Zero, you need to buy an additional Raspberry Pi Zero v1.3 Camera Cable
Outline Dimensions

AlphaBot is a robotic development platform compatible with Raspberry Pi and Arduino. It consists of the AlphaBot mainboard, the mobile chassis, and everything required to get it moving.
Just connecting a controller board, Raspberry Pi or Arduino, and combined with our open source example code, now it's all ready to start your robotic exploration: line tracking, obstacle avoidance, video monitoring, WiFi/Bluetooth/ZigBee/Infrared remote control, etc.
- Raspberry Pi/Arduino interfaces, works with either one separately, or both
- Arduino extend header, supports Arduino shields
- Modular design, plug-and-play modules like line tracking, obstacle avoidance, speed measuring, etc. eliminating the trouble of connecting mess wires.
- LM298P motor driver with diode protection circuit, more safety
- LM2596 voltage regular, provides stable 5V power to the Raspberry Pi/Arduino
- TLC1543 AD acquisition chip, allows the Pi to use analog sensors
What's on the AlphaBot Mainboard
- Raspberry Pi interface: for connecting Raspberry Pi
- Arduino interface: for connecting Arduino
- Motor interface
- Ultrasonic module interface
- Servo module interface
- Obstacle avoidance module interface
- Speed measuring interface
- Battery holder: supports 18650 batteries
- Reserved power input (not soldered): for connecting other external power supply
- Arduino expansion header: for connecting Arduino shields
- UART interface: for connecting Bluetooth module, to control the robot remotely via Bluetooth
- SPI interface: for connecting NRF24L01 wireless module
- Line tracking module interface
- TLC1543: 10-bit AD acquisition chip, allows the Pi to use analog sensors
- LM298P: dual H bridge motor driver chip, up to 2A current
- Anti-reverse diode
- Power switch
- LM2596: 5V regulator
- Power indicator
- UART switch: turn on to enable serial communication between Raspberry Pi and Arduino
- IR receiver: control the robot remotely via infrared
- Raspberry Pi/Arduino selection: select the Raspberry Pi or Arduino to control the robot peripherals






What's in the box?
Please note that the battery length SHOULD be less than 67mm, some batteries with protection plate in the market are NOT supported
- AlphaBot mainboard x1
- Tracker Sensor x1
- Photo Interrupter Sensor x2
- Infrared Proximity Sensor x2
- Motor with gearbox 2PCS x1
- AlphaBot wheel 2PCS x1
- AlphaBot acrylic chassis x1
- Motor mounting plate 4PCS x1
- omni-direction wheel x1
- 20-slots encoder disk 2PCS x1
- IR remote controller x1
- XH2.54 4cm 4Pin 2PCS x1
- XH2.54 4cm 3Pin 2PCS x1
- XH2.54 4cm 7Pin x1
- AlphaBot screws x1

Resources
SAFETY PRECAUTIONS
Li-ion and Li-po batteries are quite unstable. They may cause fire, personal injury, or property damage, if they're not properly recharged or used.
Do not reversely connect the polarities when recharging or discharging the battery.
Do not use inferior charger/charging panel to recharge the battery.
Do not mix use old batteries with new ones, avoid using batteries of different brands.
When buying a Lithium battery, you should always make sure the battery specification is compatible with the expansion board. Choose batteries from formal manufacturers and ensure the batteries will work stably and safely by aging test.
Lithium batteries have limited cycle life, they will also deteriorate as time goes by. Should be replaced with new ones when the batteries reaching their max cycle life, or working over two years, whichever comes first.
Batteries should be stored carefully and properly, keep it away from inflammables and explosives articles, away from children, avoid any safety accident caused by careless storage.
Features
The Solar Power Manager (C) is compatible with general 6V~24V solar panels. It can recharge the 18650 rechargeable Li-ion batteries through solar panel or USB TYPE-C connection, and provides 5V / 3A regulated output (with multi protocols support including PD/QC/FCP/PE/SFCP).
The module features MPPT (Maximum Power Point Tracking) function and multi protection circuits, therefore, it is able to keep operating with high-efficiency, stability, and safety. It is suitable for solar powered, low-power IoT, and other environmental protection projects.
- Supports MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel.
- Flexible battery recharging: from solar panel or USB TYPE-C power adapter.
- Compatible with 6V~24V solar panels, DC-002 jack input or screw terminal input
- Onboard MPPT SET switch, select the level closed to input level to improve recharging efficiency
- Onboard aluminum electrolytic capacitor and SMD ceramic capacitor, reducing the ripple, stable performance
- Embedded battery holder, supports 3x 18650 rechargeable Li-ion batteries
- Several LED indicators, for monitoring the status of solar panel and battery
- Multi protection circuits: over charge / over discharge / reverse-proof / over heat / over current, stable and safe to use
Supports 6V~24V solar panels
5-level voltage switch, for setting solar panel input voltage to improve efficiency

3x 18650 batteries support(not included)
Embedded battery holder for rechargeable Li-ion batteries

Application example
solar-powered control system for MCUs / development boards like:
Raspberry Pi / Jetson Nano / Arduino...

Note: for reference ONLY, the Raspberry Pi, display, solar panel are NOT included.
Resources introduction

- Solar panel input
recharging through DC-002 jack or screw terminal - TYPE-C recharging/output port
supports 5V power adapter for recharging
supports PD protocol quick charge adapter
supports PD/QC/FCP/PE/SFCP multi protocols output - USB output port
5V/3A regulated output
supports PD/QC/FCP/PE/SFCP multi protocols output
- Battery on/off switch
- BOOT button
- Quick charge indicator
- Solar panel status indicators
Solar Warning: lights up if solar panel is reversed
Solar Charge: lights up when recharging from solar panel
Solar Done: lights up when the battery is fully recharged - Battery life indicators
Outline Dimensions

What's in the box?
1 x solar manager
Need batteries? You will find our battery selection here
Resources