Special Offers
- It usually takes about 0.3s for partial refresh
- Pi Header: standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
This is an E-Ink display HAT for Raspberry Pi, 7.5inch, 800×480 resolution, with embedded controller, communicating via SPI interface.
Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.
Features- No backlight, keeps displaying last content for a long time even when power down
- Ultra low power consumption, basically power is only required for refreshing
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
- SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
- Onboard voltage translator, compatible with 3.3V/5V MCUs
- Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)
Specifications
- Operating voltage: 3.3V~5V
- Interface: SPI
- Outline dimension: 170.2mm × 111.2mm
- Display size: 163.2mm × 97.92mm
- Dot pitch: 0.205 × 0.204
- Resolution: 800×480
- Display color: black, white
- Grey scale: 2
- Full refresh time: 5s
- Refresh power: 38mW(typ.)
- Standby power: <0.017mW
- Viewing angle: >170°
Revision History
Revision V2 has been released on 2019.11, the resolution is upgraded to 800×480, from 640×384 of V1. The hardware and interface of V2 are compatible with V1, however, the related software should be updated.
| SYMBOL | DESCRIPTION |
|---|---|
| VCC | 3.3V~5V |
| GND | Ground |
| DIN | SPI MOSI pin |
| CLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output, low active |
Dimensions
What's in the box?
- 7.5inch e-Paper x1
- e-Paper Driver HAT x1
- RPi screws pack (2pcs) x1
- PH2.0 20cm 8Pin x1
2
3
4
Resources
Thanks to multi onboard protection circuits, including 500W lightningsurge, ESD protection, short circuit protection, and electrical isolation, it make the communication more safe and more reliable.
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
- Supports both traditional CAN2.0 and CAN FD protocols
- Breakout SPI control pins, for connecting with host control boards like STM32/Arduino
- Onboard electrical isolation, up to 5KV isolated voltage, stable operation, higher anti-interference capability
- Onboard lightningproof, ESD protection, short circuit protection, more safe communication
- Onboard voltage translator, select 3.3V/5V operating voltage by jumper
- Onboard 120Ω terminal resistor, configured by jumper
- Comes with development resources and manual (examples for Raspberry Pi/Arduino)
Specifications
- CAN CONTROLLER: MCP2518FD
- CAN TRANSCEIVER: MCP2562FD
- CONTROL BUS: SPI
- POWER SUPPLY: External power supply terminal OR Raspberry Pi
- SCREW TERMINALINPUT VOLTAGE: DC 8~26V
- OPERATING VOLTAGE: 5V
- LOGIC LEVEL: 3.3V/5V
- DIMENSIONS: 65.0 × 56.5mm
What Can It Do?
Enable Isolated And Stable CAN FD Capability For Your Raspberry Pi
Designed For Raspberry Pi Series
Standard Raspberry Pi 40PIN GPIO Header, Customized For Raspberry Pi Series Boards
2-Channel CAN Support
MCP2518FD CAN Controller MCP2562FD CAN Transceiver
Electrical Isolation Circuitry Safe & Stable
SM24CANB TVS Diode, ESD Protection, Transient Peak Voltage Protection
Flexible With Handy Jumpers
Easily Select 3.3V / 5V Operating Voltage, Or Enable/Disable 120Ω Terminal Resistor, Via Onboard Jumpers
What's On Board?
- MCP2518FD controller
- MCP2562FD transceiver
- SI8642ED digital isolator
- MP1584EN power chip
- RT9193-33 power chip
- B0505LS-1W power supply isolation module
- Standard Raspberry Pi 40PIN GPIO header
- CAN bus screw terminal
- External power supply terminal
8~26V DC input - MCU control pins
for use with host boards like Arduino
- 120Ω terminal resistor switch
- 3.3V/5V logic level switch
- CAN operating mode selection
A: CAN_0 and CAN_1 use two separated SPI (default)
B: CAN_0 and CAN_1 share a single SPI - Power indicator
- 2A fast resettable fuse
- Power supply reverse-proof diode
- Power supply flow backward proof diode
- Freewheeling diode
- SM24CANB TVS diode
Pinout Definition
Outline Dimensions
What's in the box?
1 x CAN FD Expansion HAT for Raspberry P
Resources
Features
- Material: Copper
- Size: 13mm x 6mm
- Weight: 2g
- Nozzle thread: M6
- Nozzle accuracy: 0.4mm
What's in the box?
5 x 0.4mm Nozzles
Features
- 6x 10/100/1000 Mbps Ethernet ports
- 2x Uplink ports
- 4x PoE ports
- IEEE 802.3af/at Power Over Ethernet (PoE) enables installation in hard to reach locations
- 60 W total power budget
- Up to 30 W power output per PoE port
What's in the box?
1 x 6-port D-link switch
A4 (210 x 297mm) squared-grid spiral-bound notebook with watermark breadboards. 158 pages, card covers.
The book also includes
- Microcontroller programming cheat sheet
- Common circuits and calculations
- Pinouts
- Resistor color codes
- ASCII table
What's in the box?
1 x Electronics notebook
100% cotton Unisex T-shirt from the Cytron for every maker that loves making stuff. Simple yet comfortable!
Comes in black color with the slogan of TRUST ME I'M A MAKER
There are several sizes of this T-shirt to accommodate everyone :) Please choose the preferred size next to the main photo. It is Unisex T-shirt so it is suitable for both male and female maker :)
- XS (Extra Small) Size
- S (Small) Size
- L (Large) Size
- M (Medium) Size
- XL (Extra Large) Size
- XXL (Double Extra Large) Size
- XXXL (Triple Extra Large) Size
Features:
- Coming from makers to makers :)
- 100% cotton, super comfortable
- The black color with:
- Front: Slogan: TRUST ME I'M A MAKER
- Back: Cytron Logo
- Available Sizes:
- Extra Small (XS):
- 36" or 91.44cm for the Chest (Chest = 2 x L)
- 25" or 63.5cm for Height
- Small (S):
- 38" or 96.52cm for the Chest (Chest = 2 x L)
- 26" or 66.04cm for Height
- Medium (M):
- 40" or 101.6cm for the Chest (Chest = 2 x L)
- 27" or 68.58cm for Height
- Large (L):
- 42" or 106.68cm for the Chest (Chest = 2 x L)
- 28" or 71.12cm for Height
- Extra Large (XL):
- 44" or 111.76cm for the Chest (Chest = 2 x L)
- 29" or 73.66cm for Height
- Double Extra Large (XXL):
- 46" or 116.84 cm for the Chest (Chest = 2 x L)
- 30" or 76.2 cm for Height
- Triple Extra Large (XXXL):
- 48" or 121.92 cm for the Chest (Chest = 2 x L)
- 31" or 78.74 cm for Height
- Extra Small (XS):
What's in the box?
1 x Trust Me T-Shirt - Black (Chosen Size)
A meteorologically minded Raspberry Pi HAT designed to make hooking up weather sensors a breeze (or a squall, or a gale).
Weather HAT is a tidy all-in-one solution for hooking up climate and environmental sensors to a Raspberry Pi. It has a bright 1.54" LCD screen and four buttons for inputs. The onboard sensors can measure temperature, humidity, pressure and light. The sturdy RJ11 connectors (remember those?) will let you easily attach wind and rain sensors. It will work with any Raspberry Pi with a 40 pin header (that's most of them except the really old ones).
You could install it outside in a suitable weatherproof enclosure (like a waterproof junction box or even a Tupperware container) and connect to it wirelessly - logging the data locally or piping it into Weather Underground, a MQTT broker or a cloud service like Adafruit IO. Alternatively, you could house your weather Pi inside and run wires to your weather sensors outside - making use of the nice screen to display readouts.
Please note: the wind and rain sensors are sold separately.
Features
- 1.54" IPS LCD screen (240 x 240)
- Four user-controllable switches
- BME280 temperature, pressure, humidity sensor (datasheet)
- LTR-559 light and proximity sensor (datasheet)
- Nuvoton MS51 microcontroller with inbuilt 12-bit ADC (datasheet)
- RJ11 connectors for connecting wind and rain sensors (sold separately)
- HAT-format board
- Fully-assembled
- Compatible with all 40-pin header Raspberry Pi models
- Python library
- Schematic
What's in the box?
1 x Weather HAT
2 x 10mm standoffs
Raspberry Pi and accessories are sold separately
Software
We've put together a Python library to give you easy access to all Weather HAT's functions, together with straightforward examples to help you learn how to read the sensors and use all the individual parts. There's also a weather station example that shows you how it's possible to combine all the functions into an application.
Our Getting Started tutorial contains a thorough walkthrough of Weather HAT's functionality plus beginner friendly instructions for installing the Python library and running the examples.
Notes
- Want to add on more I2C sensors? No problem, there's an solderless I2C header located on the back of the HAT that you can poke jumper / DuPont wires in to.
- If you'd like to hook up more analog sensors (3.3v max) we've broken out some extra ADC channels on the front of the board, as well as a convenient 3v3 power and ground.
- We've found two standoffs at the GPIO edge to be sufficient to keep this HAT firmly in place, but if you're attaching it to a full-size Pi and want to add standoffs at every corner you can pick up some more.
- Dimensions: 65 x 56.5 x 19 mm (L x W x H, including header and connectors)
Do you want to build an auto plant watering system but don’t know where to start?
Or you are a teacher and wanted to help your students to build the auto plant watering system in the most effective way?
This project kit comes with the new Maker Soil Moisture Sensor.
A capacitive moisture sensor which measures the soil moisture level by changing the probe capacitance and does not erode the sensor probe easily.
The Lesson Guide is written in simple language and comes with a step-by-step guide to make an auto plant watering system.
Click here to download PDF English Version
Lesson 1 : Hello!
- Introduction to micro:bit and MakeCode.
Lesson 2 : What’s the Soil Moisture Level?
- Display soil moisture level through micro:bit by using Maker Soil Moisture Sensor.
Lesson 3 : Dry? Moist? Or Wet?
- Monitor the soil moisture level and differentiate it between dry, moist and wet.
Lesson 4 : Water the Plant
- Turn on the water pump to water the plant when the soil is dry.
Lesson 5 : Servo Motor, Direct the Pipe!
- Control the direction of the water pipe by using a servo motor to water the plant thoroughly.
Additional Activities: Visualize Soil Moisture Level, Music On
- Plot a bar graph to show the soil moisture level and make the auto plant watering system to play melodies and sound notifications.
What’s in the box?
1 x Lesson guide (English Version)
1 x Maker Soil Moisture Sensor
1 x REKA:BIT (without micro:bit V2)
1 x Micro Submersible Water Pump DC 3V-5V with Pipe
1 x Analog Micro Servo 9g (3V-6V) with servo horns and screws
1 x Grove 4 Pin Buckled 50cm Cable
1 x Servo Male - Female Extension Cable 30cm
1 x 4xAA battery holder with DC plug
4 x PKCELL Heavy Duty AA Battery
1 x Tiny Phillips Screwdriver - Transparent
2 x Popsicle stick
3 x Cable Ties
2 x Double Sided Tapes
This SD card to SD card extension cable is perfect for protecting your SD card port! The flat flex cable is 45cm long, so it's perfect for mounting your SD card separately for easy access.
SD to SD Extension Cable Features:
- SD Card Male to SD Card Female
- Flex Cable ~ 45cm
- Supports SD Card Sizes: 16GB, 32GB 64GB 128GB
- Supports SD/SDHC/SDXC Cards
What's in the box?:
1 x SD Extension Cable
Finally available following public demand after so many of you spotted this mug on Raspberry Pi Tweets and images, this Black Design Raspberry Pi mug is the ultimate holder of coffee, tea and other late-night project beverages!
With a 330ml capacity for your favourite brew combined with superb styling, this mug is a great companion for Raspberry Pi makers and fans across the planet. Get dipping those biccies!
We also stock the original red design! Don't forget to grab a coaster whilst you're at it
Features:- Black colour with White Raspberry Pi designs
- Dishwasher safe
- 80mm diameter x 90mm tall
- 330ml capacity
- Bright and colorful!
The team at Raspberry Pi Foundation has extensively tested these mugs and can confirm that they are tea-, coffee-, and hot chocolate-compatible. They can also be used for cold drinks if that's your preference.
Note: While tested to over 1,000 domestic dishwasher cycles, it is recommended that you hand-wash this mug to keep it in tip-top condition.
What's in the box?1 x Raspberry Pi Black Ceramic Mug
Ultra Thin, Tower-style, Speed-Adjustable Fan
for reference only, Raspberry Pi4 is NOT included.
| Supported Pi | Raspberry Pi 4B |
|---|---|
| Power supply | DC 5V input (can be powered from Raspberry Pi) |
| structure | ICE Tower-style, 3x4.5mm copper tube super heat dissipation |
| rated power | 0.6W @5V, 0.12A |
| Fan | 4007 fan, 5300±10% RPM |
Female pinheader and FAN adapter V2 are available to facilitate expansion modules(Included)
for reference only, Raspberry Pi 4B and RS485 CAN HAT (B) are NOT included.
With the same cooling effect, the size is thinner and lighter than
ICE Tower Fan for Pi and ICE Tower Fan V2 for Pi
PWM Speed-Adjustable Fan and 3x4.5mm Copper Heat tube, provide effectively excellent heat dissipation
Maintain CPU Temperature Below 45°C Even In Extreme Overclocking Conditions
How to install (The fan adapter is included with this product)
What's in the box?
1 x PI4-ICE-TOWER-FAN
1 xFAN Adapter V2
1 x 2x20PIN female pinheader
1 x 2x2PIN female pinheader
1 x Acrylic bottom panel
1 x Screwdriver
1 x Silicone thermal tape and Screws pack
Specifications
- 2 x 20 female headers to mount the Pico
- 2 x 20 female headers for jumper connections to sensors etc.
- 2 x 20 screw terminals for more permanent wire connections
- Small form factor (84mm x 61mm)
- Pre-soldered headers
- GPIO pin labels printed on the board for ease of use
What's in the box?
1 x Pico expansion board
Low power, wide viewing angle, paper-like effect without electricity
Ideal for price tags, shelf labels, industrial instruments...
- Advanced Color ePaper (ACeP) technology, supports 7-Color display
- No backlight, keeps displaying last content for a long time even when power down
- Ultra low power consumption, basically power is only required for refreshing
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
- SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc.
- Onboard voltage translator, compatible with 3.3V/5V MCUs
- Comes with development resources and manual(driver board schematic, examples for Raspberry Pi/Arduino/STM32)
Specifications
| operating voltage | 3.3V/5V | display color | 7-Color |
|---|---|---|---|
| interface | 3-wire SPI, 4-wire SPI | grey scale | 2 |
| outline dimensions | 170.2 × 111.2mm | full refresh time | 35s |
| display size | 160 × 96mm | refresh power | <49.4mW (typ.) |
| DOT PITCH | 0.2 × 0.2 mm | standby current | <0.01uA (almost none) |
| RESOLUTION | 800×480 pixels | viewing angle | >170° |
Advantages of EINK
E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper.
E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180° viewing angle. It is usually used as e-reader due to its paper-like effect.
Compatible With Raspberry Pi Series Boards, Jetson Nano
For Use With Controller Boards Like Raspberry Pi/Jetson Nano/Arduino/STM32
| VCC | Power (3.3V / 5V input) |
|---|---|
| GND | Ground |
| DIN | SPI MOSI pin |
| SCLK | SPI SCK pin |
| CS | SPI chip selection, low active |
| DC | Data/Command selection (high for data, low for command) |
| RST | External reset, low active |
| BUSY | Busy status output pin |
Application examples
Suitable for price Tags, asset/equipment Tags, shelf labels, conference name tags...
Outline dimensions
What's in the box?
1 x 7.3inch e-Paper (F)
1 x Driver Board and FFC cable
1 x PH2.0 20cm 8Pin
1 x RPi screws pack (2pcs)
Resources
These kits are perfect for beginners that are just just getting exposed to the Raspberry Pi, Media enthusiasts looking to stream online content with Kodi, developers looking to exploit the many advantages of the RPI's GPIO pins and anybody looking to get some cool goodies at a great price! They contain all of the essential items that you need to get up and running in no time.
Please Note: These kits are pre-boxed and cannot be modified at all, we do however keep stock on all of the individual items so if you have a special need simply feel free to browse through the rest of our product offerings and select the items that you'd like.
What's in the box?
- Raspberry Pi Zero Wireless (This is not the Zero 2 W)
- 32GB preloaded Sandisk micro SD card preloaded with Raspberry Pi OS
- Zero adapter kit
- Official Raspberry Pi Zero Red & White Case
- Raspberry Pi Official micro USB-C power supply White 5.1V 2.5A
You might also want a standard HDMI cable that connects to the adapter or a mini HDMI cable that connects directly to the Zero.
Want to take your kit to the next level?
Turn your RPI into a Media Centre
Grab yourself a remote control, install LibreELEC or OSMC when setting up your RPI and you'll be streaming in no time. You can even add a wireless keyboard, mouse or other similar controllers
Want a cheap eco-friendly PC
Grab a Keyboard and Mouse, select Raspbian when setting up your RPI and you'll be browsing the web, sending emails, editing spreadsheets and watching videos just like you're used to with a desktop/laptop.
We know you love retro gaming!
RetroPie allows you to turn your Raspberry Pi into a retro-gaming machine Check out our Arcade section, whether you just want a retro control or a mini DIY arcade cabinet we have what you're looking for.
Did somebody say Robotics?
We've got some cool beginner's items in our robotic section
Our Kits come with the latest version of Raspberry Pi OS pre-installed, While we will certainly try our best to assist with any software related questions we cannot offer any kind of official support on community driven, open source, or non-PiShop produced proprietary software.
NOOBS, Raspbian, RetroPie, LibreELEC and OSMC are all examples of open-source software, please visit the developer's respective websites for more info.
A whole bunch of other really cool technical info can be found here.
Where do I start?.........Getting Started with Raspberry Pi
You can easily program EDU:BIT using open-sourced Microsoft MakeCode Editor. Just add EDU:BIT MakeCode Extension and you’re good to go. If you’re a beginner, you can start with the block programming mode; simply drag, drop and snap the coding blocks together. For more advanced users, you can easily switch into JavaScript or Python mode on MakeCode Editor for text-based programming.
New to coding? Don’t worry. This kit comes with a booklet covering 10+1 hands-on coding lessons, which have been creatively structured to introduce programming basics in a fun and engaging manner. Each chapter features a classic childhood game such as Rock Paper Scissors, Snakes and Ladders, Twister, and Simon Says. Follow the step-by-step guide to build the games and then have fun playing with your friends! *Game accessories are provided in this kit.
At the end of each chapter, there is a challenge which requires you to apply what you’ve learned to build a useful application for your classroom. Give it a try and if you’re stuck, we’re always here to help you. You can go to our online Resource Hub for sample codes and extra resources.
SPECIAL FEATURES
Start having fun with EDU:BIT right out of the box. Start coding right away and see your board lights up and plays melody with the press of a button. No wiring required when used as a training kit.
Cannot control servo motor and play music at the same time on your micro:bit? Servo motor refuses to move correctly? Worry no more! EDU:BIT takes care of these issues with its dedicated controller and power supply. It can even support up to 3 servo motors and 2 DC motors to actuate any creative projects you will build.
Each feature and its associated micro:bit IO pin is clearly labeled on the board for easy reference. In addition, indicator LEDs are built in on EDU:BIT to ease troubleshooting for both digital and analog IO pins.
Ready to build your own projects? You can break off the modules on EDU:BIT board for more flexibility in your project design. Plug-and-play cables are provided for you to connect the broken off Bits to the main board.
EDU:BIT Specifications
- 1x Piezo buzzer with audio jack
- 1x Sound sensor
- 1x Potentiometer
- 1x IR sensor
- 4x Programmable RGB LEDs
- 3x Big LEDs (traffic light module - red, yellow green)
- 2x Push buttons
- 3x ports for servo motors
- 2x ports for DC motors
- 1x port for I2C Interface (3.3V)
- Dimension: 157.50 mm x 124.50 mm x 19.00 mm
What's in the box?
1 x EDU:BIT board
1 x Step-by-step Guide Book
1 x USB power and data cable
2 x Game maps
2 x Game accessories
7 x Grove cables
1 x Servo motor
1 x DC motor
1 x Pulley wheel
1 x Fan blade
- EDU:BIT Resource Hub (with sample codes and extra resources)
- EDU:BIT Out-of-the-box Demo Code
- micro:bit Getting Started Guide (by microbit.org)
- MakeCode Online Editor
- MakeCode Offline Editor
- EDU:BIT Schematic, PCB Layout and PIC16F1937 Co-Processor Source Code
- MicroPython library for EDU:BIT
Visit our Blog for demo videos and more!
Note: This kit comes without micro:bit, please get it separately here.
Smart Fan
Check out this video using this smart home kit, this is Smart Fan
Smart Home Kit is a product about smart home projects base on micro:bit. We have selected components commonly used at home as TMP36 temperature sensor, sound sensor, crash sensor, servo, motor. You can build a scene like a windowsill, wardrobe and fish tank, create yourself smart sweet home and programming to intelligently driving them using micro:bit. The smart home is what makes life more practical and playing with it is what makes life more interesting.
Voice Activated Light
Here is a video by Cytron: Voice Activated Light using this kit in Bahasa Malaysia with English Subtitles:
- Plug and use connection
- Rich tutorial cases
- Connect limitless creativity with different sensors
What's in the box?
1 x Crystal Battery Box - 2 x AAA
1 x Crash E-Blocks
1 x TMP36 temperature sensor E-blocks
1 x Rainbow LED E-blocks
1 x Simulation noise sensor E-blocks
1 x Light sensor E-blocks
1 x Soil Moisture sensor E-blocks
1 x Relay E-blocks
1 x DC Motor E-blocks
1 x 180º Servo E-blocks
1 x Submersible pump E-blocks
1 x Screw Driver
1 x Micro-B USB Cable
1 x OLED Display
1 x Smart Home kit manual book
- Introduction to Smart Home Kit
- Introduction to sensor:bit
- Case01：Voice-activated Lights
- Case02：Smart Fan
- Case03：Auto Windows
- Case04：Smart Wardrobe
- Case05：Water Level Alarming
- Case 06: Smart Telecontrol Door Opener
- Case 07: Smart Decibel Tester
- Case 08: Simple Spirometer
- Case 09: Lie Detector
- Case 10: Simple Alarm Box
- Case 11: Intruder Detection System
- Cytron tutorial: Smart Home Kit - Smart Fan, with video the steps.
- Cytron tutorial: Smart Home Kit - Voice Activated Light, with video and guides
Handle the heated soldering iron with extreme care, as the high temperature of the ion can cause fires or painful burns.
Specifications
- Voltage: AC220V
- Colour: blue/silver
- Material: ABS and metal
- Size: 24*3*3cm
What's in the box?
1 x 40W Soldering Iron
Handle the heated soldering iron with extreme care, as the high temperature of the ion can cause fires or painful burns.
Specifications
- Voltage: AC220V
- Colour: blue/silver
- Material: ABS and metal
- Size: 24x3x3cm
What's in the box?
1 x 60W Soldering Iron
Note: This is the beginner kit for Arduino UNO R3 lovers. It comes with everything (except computer) that you need to learn Arduino :)
Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently support Mac OS X, Windows, and Linux).
Now, with this comprehensive beginner kit which includes the famous UNO R3 compatible as the main controller. All the applications and projects you want can be done with this set.
This kit is suitable for:
- Engineering students: Controller and Electronics are a must-have topic in all engineering courses, Electronics, Mechanical, or even Civil Engineering. This kit is perfect for you to understand the basics of controller, electronics, sensors, actuator, and programming.
- Teachers: Perfect for student-teacher projects, for example in RBT (Reka Bentuk Teknologi)
- Electronic enthusiasts: Kickstart your next project utilizing all the components in this kit.
- Robot Builders: All the sensors and actuators are suitable in robotics.
- Software Engineers: Arduino will be an excellent platform for establishing interfaces on the computer to receive data from the outside world and for communication applications.
Features
- Comes with UNO R3 Compatible (CH340) board
- Pack in a two layers plastic case, suitable for long usage and tidy storage
- Includes various type of sensors, and actuators (motors, LEDs, buzzer)
- Perfect for learning Arduino ecosystem, electronics, and programming
- You only need a computer to get started
- Power everything from your USB port which is needed for program loading in any case.
What's in the box?
1 x USB Type B Cable, to power and program loading into UNO R3 CH340 board, 40cm length
1 x 30 pcs Jumper Cable Male to Male
1 x 10 ways Dupont Male to Female wire
1 x Large Size Breadboard, 830 holes
1 x Four segments 7 Segment Display
1 x Single 7 Segment Display
1 x 8 x 8 Dot matrix module
1 x Parallel LCD 16 * 2 Character
1 x UNL2003 Driver board
5 x 5mm Red LED
5 x 5mm Green LED
5 x 5mm Yellow LED
1 x 28BJJ Unipolar Stepper Motor
1 x SG90 Servo Motor
1 x 9V Battery Clip Arduino Compatible
5 x 220R Resistor
5 x 10K Resistor
5 x 1K Resistor
1 x 10K potentiometer/variable resistor
1 x Male Header 1 x 40, for solder 2x16 Character LCD
1 x Active Buzzer
1 x Passive Buzzer
4 x Yellow Cap Push Button
1 x LM35 Temperature sensor
1 x Tilt sensor
1 x Flame sensor
1 x Water sensor
2 x 5mm LDR
1 x IR sensor (LED shape)
1 x Infrared Remote Control Receiver
1 x IR Remote (battery CR2025 is included)
1 x 74HC595N IC, Serial to Parallel IC for Output pin expansion
1 x 4 x 4 Key button
1 X RFID RC522 Mifare Module
1 X RFID Mifare keychain
1 X RFID Mifare card
1 x Joystick module
1 x Sound module
1 x Relay module
1 x 9V battery snap to DC Barrel Jack (9V battery is NOT included)
1 x RTC module (coin cell battery is included)
1 x Small SMD parts case
Resources
- Download Arduino IDE
- Official Arduino Site
- CH34X driver (Please ensure the Maker UNO is plug into computer USB port during driver installation)
- Windows (V3.5 Mar2019)
- Mac OS (V1.5 Mar2019)
- Linux (V1.5 Mar2019) (Normally is readily installed)
- CH34X Driver - Get the latest driver from the factory
6 DIFFERENT SIZES / STYLES
- 0-Point Phillips
- 1-Point Phillips
- 1.4mm Flathead
- 2.0mm Flathead
- 2.4mm Flathead
- 3.0mm Flathead
What's in the box?
6 x mini screwdrivers