Raspberry Pi

Sort By:  
A low cost, high-performance microcontroller board built around Raspberry Pi's very own chip - the RP2040.
R69.90  Inc VAT
While the Zero 1.3 and the Zero W have limits set to 1 per order, the Zero WH has no limits. Finally you can buy as many as you need to complete that project.
R299.90  Inc VAT
R489.90  Inc VAT
R1,079.90  Inc VAT
R1,089.90
R1,489.90  Inc VAT
R979.90  Inc VAT
R999.90
Maximum 1 Unit Per Customer. We Reserve the Right to Cancel Repeat Orders.
R259.90  Inc VAT
The Official Raspberry Pi Power Supply - Shipped with easily interchangeable heads for the UK and EU.
R165.90  Inc VAT
Limited to 1 RPI Zero per customer (including units included in kits), we reserve the right to cancel duplicate and/or multiple orders.
R194.30  Inc VAT
The Official Raspberry Pi Zero & Zero Wireless Case is now available!
R59.90  Inc VAT
R529.90  Inc VAT
R719.90  Inc VAT
R599.90  Inc VAT
Raspberry Pi Official Pi4 4GB Desktop Kit (RPi44 official desktop kit)

This is the official Pi4 kit from the Raspberry Pi Foundation.



This kit contains:


More info on the Pi4 available at https://www.raspberrypi.org/blog/raspberry-pi-4-on-sale-now-from-35/
and https://www.raspberrypi.org/products/raspberry-pi-4-model-b/

R2,199.90  Inc VAT
Raspberry Pi Pico (RPi Pico)

https://www.raspberrypi.org/blog/raspberry-pi-silicon-pico-now-on-sale/

https://www.raspberrypi.org/products/raspberry-pi-pico/

https://www.youtube.com/watch?v=ZY-HrRGCQ4w

YouTube video on Pico by Jeff Geerling

Raspberry Pi Pico, a microcontroller board built on silicon designed here at Raspberry Pi.

Whether you choose to use our C/C++ SDK, or the official MicroPython port, everything you need to get started is here. You’ll also find links to the technical documentation for both the Raspberry Pi Pico microcontroller board and our RP2040 microcontroller chip.



Board Specifications

  • RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom
  • Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz
  • 264kB of SRAM, and 2MB of on-board Flash memory
  • Castellated module allows soldering direct to carrier boards
  • USB 1.1 Host and Device support
  • Low-power sleep and dormant modes
  • Drag & drop programming using mass storage over USB
  • 26 multi-function GPIO pins
  • 2×SPI, 2×I2C, 2×UART, 3×12-bit ADC, 16×controllable PWM channels
  • Accurate clock and timer on-chip
  • Temperature sensor
  • Accelerated floating point libraries on-chip
  • 8×Programmable IO (PIO) state machines for custom peripheral support


Download Pinout Diagram


Documentation

Documentation for the Raspberry Pi Pico board and the RP2040 microcontroller:

The API level Doxygen documentation for the Raspberry Pi Pico C/C++ SDK is available as a micro-site.

While Raspberry Pi Pico does not come with anything soldered to its pads, we will recommend that users fit 2.54mm pitch male pin strip headers.


A low cost, high-performance microcontroller board built around Raspberry Pi's very own chip - the RP2040.
R69.90  Inc VAT
Raspberry Pi Zero Wireless WH (Pre-Soldered Header) (ZERO WH board)

The Raspberry Pi Zero WH has landed at PiShop! The Raspberry Pi Zero is an ultra low cost and ultra small variant of the original Raspberry Pi. It's tiny, measuring just 65mm x 30mm, and is perfectly designed for embedded applications, wearables, prototyping and any other Pi based tinkering you can think of, on a micro scale! The Raspberry Pi Zero Wireless features on board Wireless Internet & Bluetooth for all your connectivity needs!

The Raspberry Pi Zero features a BCM2835 chipset, overclocked to 1Ghz with 512MB RAM, and the same 1080p video output, so there's plenty of oomph in that little board. It also features the same 40 pin GPIO layout as the Raspberry Pi 2/B+/A+, with a pre-soldered male header. With it's small form factor and reduction in connectors, the Raspberry Pi Zero only uses ~ 140mA at 5V!

Unlike it's larger brothers and sisters, the Raspberry Pi Zero has an unpopulated composite (RCA) header and an unpopulated reset header. There's also no DSI screen port, no ethernet, no analogue audio and no full sized USB ports. Instead, the Pi Zero features a micro-USB power port, a micro USB OTG host port (for peripherals e.g. WiFi dongle), and a mini HDMI port for video. 

HAT Compatibility Note: The Pi Zero is fully compatible with all HAT breakout boards, as it features the same 40 Pin GPIO as the Raspberry Pi 2/B+/A+

Raspberry Pi Zero Wireless Features:

  • BCM2835 chipset, Overclocked to 1Ghz 
  • 512MB RAM
  • Tiny Form Factor: 65mm x 30mm x 5mm
  • Fully HAT compatible
  • 40pin GPIO with pre-soldered header
  • Stream and watch Hi-definition video output at 1080P
  • Micro SD Slot for OS 
  • Tiny Current Draw ~ 140mA at 5V!
  • Mini-HDMI for Video
  • Micro-USB OTG Host for Data
  • Micro-USB for Power
  • Micro-CSI Camera Port
  • On-Board WiFi
  • On-Board Bluetooth

Raspberry Pi Operating System Downloads: https://www.raspberrypi.org/downloads/
Getting Started with Raspberry Pi

While the Zero 1.3 and the Zero W have limits set to 1 per order, the Zero WH has no limits. Finally you can buy as many as you need to complete that project.
R299.90  Inc VAT
Raspberry Pi3 - Model A+ (Pi3A+ board)

The Raspberry Pi 3 Model A+ is the latest product in the Raspberry Pi 3 range. Like the Raspberry Pi 3 Model B+, it boasts a 64-bit quad core processor running at 1.4 GHz, dual-band 2.4 GHz and 5 GHz wireless LAN, and Bluetooth 4.2/BLE. The dual-band wireless LAN comes with modular compliance certification, allowing the board to be designed into end products with significantly reduced wireless LAN compliance testing, improving both cost and time to market.

The Raspberry Pi 3 Model A+ features 512mb SDRAM (over the Pi 3 B+'s 1GB), has no Ethernet port or function, and includes only one USB port. The Raspberry Pi 3 Model A+ has the same mechanical footprint as the Raspberry Pi 1 Model A+. 

Please Note. It is recommended to use a 2.5A Power Supply with the Raspberry Pi 3A+. This purchase is for the Raspberry Pi 3 Model A+ Board only.

Specifications

  • Processor
    • Broadcom BCM2837B0 chipset.
    • 1.4GHz Quad-Core ARM Cortex-A53 (64Bit)
  • Connectivity
    • 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE
    • 1 × USB 2.0 ports
  • GPU
    • Dual Core VideoCore IV® Multimedia Co-Processor. Provides Open GL ES 2.0, hardware-accelerated OpenVG, and 1080p30 H.264 high-profile decode.
    • Capable of 1Gpixel/s, 1.5Gtexel/s or 24GFLOPs with texture filtering and DMA infrastructure
  • Memory
    • 512mb LPDDR2
  • Operating System
    • Boots from Micro SD card, running a version of the Linux operating system or Windows 10 IoT
  • Dimensions
    • 65 x 56 x 8.5mm
  • Power
    • 5V/2.5A DC via Micro USB Connector
    • 5V DC via GPIO Header

Connectors

    • Video Output
      • HDMI (rev 1.3 & 1.4)
      • Composite RCA (PAL and NTSC)
    • Audio Output
      • Audio Output 3.5mm jack
      • HDMI
      • USB 1 x USB 2.0 Connector
    • GPIO Connector
      • 40-pin 2.54 mm (100 mil) expansion header: 2x20 strip
      • Providing 27 GPIO pins as well as +3.3 V, +5 V and GND supply lines
    • Camera Connector
      • 15-pin MIPI Camera Serial Interface (CSI-2)
    • Display Connector
      • Display Serial Interface (DSI) 15 way flat flex cable connector with two data lanes and a clock lane
    • Memory Card Slot 
      • Push/Pull Micro SDIO

    Getting Started with Raspberry Pi
    R489.90  Inc VAT
    Official Raspberry Pi US Keyboard (Red/White) (Official red/white keyboard)

    The Official Raspberry Pi Keyboard is finally here!

    This sleek and stylish keyboard from the team at Raspberry Pi includes three in-built USB 2.0 type-A ports for powering other peripherals (such as the official Raspberry Pi mouse)!

    Please Note. This keyboard is available in 6 language formats: UK, US, DE, FR, ES & IT. This model is the US version as used in South Africa.


    Keyboard Specification:

    • 79-key keyboard (78-key US keyboard)
    • 3 USB 2.0 type-A ports for powering other peripherals
    • Automatic keyboard language detection
    • USB type-A to micro USB type-B cable for connection
    • Compatible with all Raspberry Pi products
    • Ergonomic design for comfortable use
    • Available in Red/White and Black/Grey
    R279.90  Inc VAT
    Official Raspberry Pi Mouse (Red/White) (Official red/white mouse)

    The Official Raspberry Pi Mouse is finally here!

    This sleek, stylish and ergonomic mouse from the team at Raspberry Pi includes three buttons, two main ones for right and left click, and a scroll wheel with button for scrolling. . . and more clicking. . . what more do you need from a mouse!

    Mouse Specification:

    • Three-button optical mouse
    • Scroll wheel
    • USB type-A connector
    • Compatible with all Raspberry Pi products
    • Ergonomic design for comfortable use
    • Available in Red/White and Black/Grey
    • This mouse will look great with your Red/White official keyboard
    R119.90  Inc VAT
    Official Raspberry Pi Mouse (black/grey) (Official black/grey mouse)

    The Official Raspberry Pi Mouse is finally here!

    This sleek, stylish and ergonomic mouse from the team at Raspberry Pi includes three buttons, two main ones for right and left click, and a scroll wheel with button for scrolling. . . and more clicking. . . what more do you need from a mouse!

    Mouse Specification:

    • Three-button optical mouse
    • Scroll wheel
    • USB type-A connector
    • Compatible with all Raspberry Pi products
    • Ergonomic design for comfortable use
    • Available in Black/Grey and Red/White
    R119.90  Inc VAT
    Official Raspberry Pi US Keyboard (Black/Grey) (Official black/grey keyboard)

    The Official Raspberry Pi Keyboard is finally here!

    This sleek and stylish keyboard from the team at Raspberry Pi includes three in-built USB 2.0 type-A ports for powering other peripherals (such as the official Raspberry Pi mouse)!

    Please Note. This keyboard is available in 6 language formats: UK, US, DE, FR, ES & IT. This model is the US version as used in South Africa.


    Keyboard Specification:

    • 79-key keyboard (78-key US keyboard)
    • 3 USB 2.0 type-A ports for powering other peripherals
    • Automatic keyboard language detection
    • USB type-A to micro USB type-B cable for connection
    • Compatible with all Raspberry Pi products
    • Ergonomic design for comfortable use
    • Available in Red/White and Black/Grey
    R279.90  Inc VAT
    Raspberry Pi 4 Model B 4GB (Pi44 B 4GB board)

    Please Note: You will need the newest version of NOOBS or Raspbian for the Pi4, a USB type C power supply or adapter and a micro HDMI cable or adapter


    Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor speed, multimedia performance, memory, and connectivity compared to the prior-generation Raspberry Pi 3 Model B+, while retaining backwards compatibility and similar power consumption. For the end user, Raspberry Pi 4 Model B provides desktop performance comparable to entry-level x86 PC systems.

    This product’s key features include a high-performance 64-bit quad-core processor, dual-display support at resolutions up to 4K via a pair of micro-HDMI ports, hardware video decode at up to 4Kp60, up to 4GB of RAM, dual-band 2.4/5.0 GHz wireless LAN, Bluetooth 5.0, Gigabit Ethernet, USB 3.0, and PoE capability (via a separate PoE HAT add-on).

    The dual-band wireless LAN and Bluetooth have modular compliance certification, allowing the board to be designed into end products with significantly reduced compliance testing, improving both cost and time to market.

    Specifications

    • Processor: Broadcom BCM2711, quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    • Memory: 1GB, 2GB or 4GB LPDDR4 (depending on model)
    • Connectivity: 2.4 GHz and 5.0 GHz IEEE 802.11b/g/n/ac wireless
    • LAN, Bluetooth 5.0, BLE Gigabit Ethernet, 2 × USB 3.0 ports, 2 × USB 2.0 ports.
    • GPIO: Standard 40-pin GPIO header (fully backwards-compatible with previous boards)
    • Video & sound: 2 × micro HDMI ports (up to 4Kp60 supported), 2-lane MIPI DSI display port, 2-lane MIPI CSI camera port, 4-pole stereo audio and composite video port
    • Multimedia: H.265 (4Kp60 decode); H.264 (1080p60 decode, 1080p30 encode); OpenGL ES, 3.0 graphics
    • SD card support: Micro SD card slot for loading operating system and data storage
    • Input power: 5V DC via USB-C connector (minimum 3A1), 5V DC via GPIO header (minimum 3A1)
    • Power over Ethernet (PoE)–enabled (requires separate PoE HAT)
    • Environment: Operating temperature 0–50oC
    • Compliance: For a full list of local and regional product approvals, please visit https://www.raspberrypi.org/documentation/hardware/raspberrypi/conformity.md
    • Production lifetime: The Raspberry Pi 4 Model B will remain in production until at least January 2026.
    More info on the Pi4 available at https://www.raspberrypi.org/blog/raspberry-pi-4-on-sale-now-from-35/

    If your new Raspberry Pi 4 is not displaying anything, but is booting:
    Please change the following settings in the /boot/config.txt setting. You can access these settings in a few ways.

    1. Using another display to access the file:   sudo nano /boot/config.txt
    2. Insert the SD card into a computer/laptop and open the boot partition

    Uncomment and change or add to the bottom of the file:

    hdmi_safe=1
    hdmi_force_hotplug=1
    hdmi_ignore_edid=0xa5000080
    hdmi_group=2
    hdmi_mode=81 (or 39 this will depend on the type of display)
    config_hdmi_boost=9
    dtoverlay=vc4-fkms-v3d
    max_framebuffers=2

    Not all of these settings may be necessary, this will again depend on your type of display, however adding them all and removing one by one will help find the ones you may need.

    WARNINGS
    • This product should only be connected to an external power supply rated at 5V/3A DC or 5.1V/ 3A DC minimum. A good quality 2.5A power supply can be used if downstream USB peripherals consume less than 500mA in total. Any external power supply used with the Raspberry Pi 4 Model B shall comply with relevant regulations and standards applicable in the country of intended use.
    • This product should be operated in a well-ventilated environment and, if used inside a case, the case should not be covered.
    • This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items.
    • The connection of incompatible devices to the GPIO connection may affect compliance and result in damage to the unit and invalidate the warranty.
    • All peripherals used with this product should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors and mice when used in conjunction with the Raspberry Pi.
    • Where peripherals are connected that do not include the cable or connector, the cable or connector must offer adequate insulation and operation in order that the relevant performance and safety requirements are met.

    SAFETY INSTRUCTIONS
    To avoid malfunction or damage to this product please observe the following:
    • Do not expose to water, moisture or place on a conductive surface whilst in operation.
    • Do not expose it to heat from any source; Raspberry Pi 4 Model B is designed for reliable operation at normal ambient room temperatures.
    • Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors.
    • Avoid handling the printed circuit board whilst it is powered and only handle by the edges to minimise the risk of electrostatic discharge damage.
    R1,079.90  Inc VAT
    R1,089.90
    Raspberry Pi4 Official USB-C 15.3W power supply White 5.1V 3A (Pi4 3A power white)

    The official Raspberry Pi USB-C power supply is designed to power the latest Raspberry Pi 4 Model B computers, which were released in June 2019.
    Featuring a captive USB-C cable, the power supply is available in four different models to suit different international power sockets, and in two colours, white and black.

    If you need to use the power supply for an earlier model RPi or the zero you'll need a type C to micro B adapter than you will find at https://www.pishop.co.za/store/rpi-power/usb-type-c-female-to-micro-usb-male-adapter

    Specifications

    Output
    • Output voltage: +5.1V DC
    • Minimum load current: 0A
    • Nominal load current: 3.0A
    • Maximum power: 15.3W
    • Load regulation: ±5%
    • Line regulation: ±2%
    • Ripple & noise: 120mVp-p
    • Rise time: 100ms maximum to regulation limits for DC outputs
    • Turn-on delay: 3000ms maximum at nominal input AC voltage and full load
    • Protection: Short circuit protection, Overcurrent protection, Over temperature protection
    • Efficiency: 81% minimum (output current from 100%,75%, 50%, 25%)72% minimum at 10% load
    • Output cable: 1.5m 18AWG
    • Output connector: USB Type-C


    Input
    • Voltage range: 100-240Vac (rated)
    • 96-264Vac (operating)
    • Frequency: 50/60Hz ±3Hz
    • Current: 0.5A maximum
    • Power consumption (no load): 0.075W maximum
    • Inrush current: No damage shall occur and the input fuse shall not blow
    Case material
    UL94V-1

    AC pin material
    Brass (NI plated)

    WARNINGS
    • This product should be operated in a well-ventilated environment.
    • The connection of incompatible devices to this power supply may affect compliance, result in damage to the unit and invalidate the warranty.

    SAFETY INSTRUCTIONS
    To avoid malfunction or damage to this product please observe the following:
    • Do not expose to water or moisture, or place on a conductive surface whilst in operation.
    • Do not expose to heat from any source; this is designed for reliable operation at normal ambient room temperatures.
    • Do not attempt to open or remove the power supply case.
    R139.90  Inc VAT
    Raspberry Pi 4 Model B 8GB (Pi48 B 8GB board)

    Please Note: You will need the newest version of NOOBS or Raspbian for the Pi4, a USB type C power supply or adapter and a micro HDMI cable or adapter


    Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor speed, multimedia performance, memory, and connectivity compared to the prior-generation Raspberry Pi 3 Model B+, while retaining backwards compatibility and similar power consumption. For the end user, Raspberry Pi 4 Model B provides desktop performance comparable to entry-level x86 PC systems.

    This product’s key features include a high-performance 64-bit quad-core processor, dual-display support at resolutions up to 4K via a pair of micro-HDMI ports, hardware video decode at up to 4Kp60, up to 8GB of RAM, dual-band 2.4/5.0 GHz wireless LAN, Bluetooth 5.0, Gigabit Ethernet, USB 3.0, and PoE capability (via a separate PoE HAT add-on).

    The dual-band wireless LAN and Bluetooth have modular compliance certification, allowing the board to be designed into end products with significantly reduced compliance testing, improving both cost and time to market.

    Specifications

    • Processor: Broadcom BCM2711, quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    • Memory: 1GB, 2GB, 4GB or 8GB LPDDR4 (depending on model)
    • Connectivity: 2.4 GHz and 5.0 GHz IEEE 802.11b/g/n/ac wireless
    • LAN, Bluetooth 5.0, BLE Gigabit Ethernet, 2 × USB 3.0 ports, 2 × USB 2.0 ports.
    • GPIO: Standard 40-pin GPIO header (fully backwards-compatible with previous boards)
    • Video & sound: 2 × micro HDMI ports (up to 4Kp60 supported), 2-lane MIPI DSI display port, 2-lane MIPI CSI camera port, 4-pole stereo audio and composite video port
    • Multimedia: H.265 (4Kp60 decode); H.264 (1080p60 decode, 1080p30 encode); OpenGL ES, 3.0 graphics
    • SD card support: Micro SD card slot for loading operating system and data storage
    • Input power: 5V DC via USB-C connector (minimum 3A1), 5V DC via GPIO header (minimum 3A1)
    • Power over Ethernet (PoE)–enabled (requires separate PoE HAT)
    • Environment: Operating temperature 0–50oC
    • Compliance: For a full list of local and regional product approvals, please visit https://www.raspberrypi.org/documentation/hardware/raspberrypi/conformity.md
    • Production lifetime: The Raspberry Pi 4 Model B will remain in production until at least January 2026.
    More info on the Pi4 available at https://www.raspberrypi.org/blog/raspberry-pi-4-on-sale-now-from-35/

    If your new Raspberry Pi 4 is not displaying anything, but is booting:
    Please change the following settings in the /boot/config.txt setting. You can access these settings in a few ways.

    1. Using another display to access the file:   sudo nano /boot/config.txt
    2. Insert the SD card into a computer/laptop and open the boot partition

    Uncomment and change or add to the bottom of the file:

    hdmi_safe=1
    hdmi_force_hotplug=1
    hdmi_ignore_edid=0xa5000080
    hdmi_group=2
    hdmi_mode=81 (or 39 this will depend on the type of display)
    config_hdmi_boost=9
    dtoverlay=vc4-fkms-v3d
    max_framebuffers=2

    Not all of these settings may be necessary, this will again depend on your type of display, however adding them all and removing one by one will help find the ones you may need.

    WARNINGS
    • This product should only be connected to an external power supply rated at 5V/3A DC or 5.1V/ 3A DC minimum. A good quality 2.5A power supply can be used if downstream USB peripherals consume less than 500mA in total. Any external power supply used with the Raspberry Pi 4 Model B shall comply with relevant regulations and standards applicable in the country of intended use.
    • This product should be operated in a well-ventilated environment and, if used inside a case, the case should not be covered.
    • This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items.
    • The connection of incompatible devices to the GPIO connection may affect compliance and result in damage to the unit and invalidate the warranty.
    • All peripherals used with this product should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors and mice when used in conjunction with the Raspberry Pi.
    • Where peripherals are connected that do not include the cable or connector, the cable or connector must offer adequate insulation and operation in order that the relevant performance and safety requirements are met.

    SAFETY INSTRUCTIONS
    To avoid malfunction or damage to this product please observe the following:
    • Do not expose to water, moisture or place on a conductive surface whilst in operation.
    • Do not expose it to heat from any source; Raspberry Pi 4 Model B is designed for reliable operation at normal ambient room temperatures.
    • Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors.
    • Avoid handling the printed circuit board whilst it is powered and only handle by the edges to minimise the risk of electrostatic discharge damage.
    R1,489.90  Inc VAT
    Raspberry Pi High Quality camera board (HQ camera)
    Overview

    The Raspberry Pi High Quality Camera is the latest camera accessory from Raspberry Pi. It offers higher resolution (12 megapixels, compared to 8 megapixels), and sensitivity (approximately 50% greater area per pixel for improved low-light performance) than the existing Camera Module v2, and
    is designed to work with interchangeable lenses in both C- and CS-mount form factors. Other lens form factors can be accommodated using third-party lens adapters.

    The High Quality Camera provides an alternative to the Camera Module v2 for industrial and consumer applications, including security cameras, which require the highest levels of visual fidelity and/or integration with specialist optics. It is compatible with all models of Raspberry Pi computer from Raspberry Pi 1 Model B onwards, using the latest software release from www.raspberrypi.org.(1)

    The package comprises a circuit board carrying a Sony IMX477 sensor, an FPC cable for connection to a Raspberry Pi computer, a milled aluminium lens mount with integrated tripod mount and focus adjustment ring, and a C- to CS-mount adapter.

    (1) Excluding early Raspberry Pi Zero models, which lack the necessary FPC connector. Later Raspberry Pi Zero models require an adapter FPC, sold separately.

    Specifications

    Sensor:Sony IMX477R stacked, back-illuminated sensor
    12.3 megapixels
    7.9 mm sensor diagonal
    1.55 μm × 1.55 μm pixel size
    Output:RAW12/10/8, COMP8
    Back focus:Adjustable (12.5 mm–22.4 mm)
    Lens standards:C-mount
    CS-mount (C-CS adapter included)

    IR cut filter:
     Integrated(2)
    Ribbon cable length:200 mm
    Tripod mount: 1/4”-20

    Compliance:
    FCC 47 CFR Part 15, Subpart B, Class B Digital Device
    Electromagnetic Compatibility Directive (EMC) 2014/30/EU
    Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU
    Production lifetime:The Raspberry Pi High Quality Camera will remain in production until at least January 2026

    (2) Can be removed to enable IR sensitivity. Modification is irreversible.

    Physical specifications



    SAFETY INSTRUCTIONS
    To avoid malfunction or damage to this product, please observe the following:
    • Before connecting the device, shut down your Raspberry Pi computer and disconnect it from
    external power.
    • If the cable becomes detached, pull the locking mechanism forward on the connector, insert the ribbon
    cable ensuring the metal contacts face towards the circuit board, then push the locking mechanism back into place.
    • This device should be operated in a dry environment at 0–50°C.
    • Do not expose it to water or moisture, or place on a conductive surface whilst in operation.
    • Do not expose it to excessive heat from any source.
    • Care should be taken not to fold or strain the ribbon cable.
    • Care should be taken when screwing in parts or fitting a tripod. A cross-thread can cause irreparable damage and void the warranty.
    • Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board
    and connectors.
    • Avoid handling the printed circuit board whilst it is powered and only handle by the edges to minimise the risk of electrostatic discharge damage.
    • Store in a cool, dry location.
    • Avoid rapid changes of temperature, which can cause moisture build up in the device, affecting
    image quality.

    How to use this camera: https://www.youtube.com/watch?v=sAXDgByhcJU

    and another video by ETA PRIME: https://www.youtube.com/watch?v=VDWORgW31Sw




    R979.90  Inc VAT
    R999.90
    Official Black 2m Micro-HDMI to Standard HDMI (type A) for Pi4 (Pi4 off Black 2m micro HDMI cable)


    Official Raspberry Pi Micro HDMI to HDMI cable, fully licensed by Raspberry Pi and manufactured for the Raspberry Pi 4 Model B.

    Perfect for running a dual screen setup with the new Raspberry Pi 4 Model B.

    Specifications:

    • 19-pin HDMI Type D(M) to 19-pin HDMI Type A(M)
    • 2m black cable
    • Nickel-plated plugs
    • 4Kp60 compliant
    • RoHS compliant
    • 3Mohm 300VDC insulation, withstands 300VDC for 0.1s


    R119.90  Inc VAT
    Raspberry Pi Zero W (ZERO Wireless board)


    Maximum 1 Unit Per Order. If you require Raspberry Pi Zero Wireless in bulk, we allow quantity purchases of the Raspberry Pi Zero Wireless with pre-soldered headers!

    The Brand New Raspberry Pi Zero Wireless has landed at PiShop! The Raspberry Pi Zero is an ultra low cost and ultra small variant of the original Raspberry Pi. It's tiny, measuring just 65mm x 30mm, and is perfectly designed for embedded applications, wearables, prototyping and any other Pi based tinkering you can think of, on a micro scale! The Raspberry Pi Zero Wireless features on board Wireless Internet & Bluetooth for all your connectivity needs!

    The Raspberry Pi Zero features a BCM2835 chipset, overclocked to 1Ghz with 512MB RAM, and the same 1080p video output, so there's plenty of oomph in that little board. It also features the same 40 pin GPIO layout as the Raspberry Pi 2/B+/A+, which you'll need to solder your own headers to. With it's small form factor and reduction in connectors, the Raspberry Pi Zero only uses ~ 140mA at 5V!

    Unlike it's larger brothers and sisters, the Raspberry Pi Zero has an unpopulated GPIO, unpopulated composite (RCA) header and an unpopulated reset header. There's also no DSI screen port, no ethernet, no analogue audio and no full sized USB ports. Instead, the Pi Zero features a micro-USB power port, a micro USB OTG host port (for peripherals e.g. WiFi dongle), and a mini HDMI port for video. 

    HAT Compatibility Note: The Pi Zero is fully compatible with all HAT breakout boards, as it features the same 40 Pin GPIO as the Raspberry Pi 2/B+/A+

    Raspberry Pi Zero Wireless Features:

    • BCM2835 chipset, Overclocked to 1Ghz 
    • 512MB RAM
    • Tiny Form Factor: 65mm x 30mm x 5mm
    • Fully HAT compatible
    • 40pin GPIO (Unpopulated)
    • Stream and watch Hi-definition video output at 1080P
    • Micro SD Slot for OS 
    • Tiny Current Draw ~ 140mA at 5V!
    • Mini-HDMI for Video
    • Micro-USB OTG Host for Data
    • Micro-USB for Power
    • Micro-CSI Camera Port
    • On-Board WiFi
    • On-Board Bluetooth

    Raspberry Pi Operating System Downloads: https://www.raspberrypi.org/downloads/
    Getting Started with Raspberry Pi

    Maximum 1 Unit Per Customer. We Reserve the Right to Cancel Repeat Orders.
    R259.90  Inc VAT
    Raspberry Pi Official Pi3/ZERO/Pico Micro USB Universal Power Supply 5.1V 2.5A (White) (Pi3 Power 2.5A White)

    You'll need a USB Type C adapter to use this supply for Pi 4

    The Official Raspberry Pi Power Supply - 
    Shipped with easily interchangeable heads for the UK, US, EU and Australia you can now use your Pi in all four corners of the world! 

    This PSU supports up to 2.5A of current, so it won't let you down when powering hungry devices through your Raspberry Pi 3 Model B

    Technical Data

    • 5.1V 2.5A Output
    • 1.5m Cable
    • White with Raspberry Pi Logo
    • Input Voltage AC Max: 264V
    • Input Voltage AC Min: 90V
    • Output Connector: USB Micro
    • Output Voltage Nom.: 5.1V
    • Interchangeable Adaptor - EU/UK/US/AUS

      The below is a copy from https://www.raspberrypi.org/help/faqs/#powerReqs.

      Here is a table comparing the amount of power drawn in amps under different situations:

        Pi1 (B+)Pi2 BPi3 B (Amps)Zero (Amps)
      BootMax0.260.400.750.20
       Avg0.220.220.350.15
      IdleAvg0.200.220.300.10
      Video playback (H.264)Max0.300.360.550.23
       Avg0.220.280.330.16
      StressMax0.350.821.340.35
       Avg0.320.750.850.23
      Test conditions used a standard Raspbian image (current as of 26 Feb 2016),
       
    The Official Raspberry Pi Power Supply - Shipped with easily interchangeable heads for the UK and EU.
    R165.90  Inc VAT
    Raspberry Pi Zero v1.3 (RPi Zero v1.3 board)

    Maximum 1 Unit Per Order. If you require Raspberry Pi Zero Wireless in bulk, we allow quantity purchases of the Raspberry Pi Zero Wireless with pre-soldered headers!

    The Raspberry Pi Zero features a BCM2835 chipset, overclocked to 1Ghz with 512MB RAM, and the same 1080p video output, so there's plenty of oomph in that little board. It also features the same 40 pin GPIO layout as the Raspberry Pi 2/B+/A+, which you'll need to solder your own headers to. With it's small form factor and reduction in connectors, the Raspberry Pi Zero only uses ~ 140mA at 5V!

    Unlike it's larger brothers and sisters, the Raspberry Pi Zero has an unpopulated GPIO, unpopulated composite (RCA) header and an unpopulated reset header. There's also no DSI screen port, no ethernet, no analogue audio and no full sized USB ports. Instead, the Pi Zero features a micro-USB power port, a micro USB OTG host port (for peripherals e.g. WiFi dongle), and a mini HDMI port for video. 

    HAT Compatibility Note: The Pi Zero is fully compatible with all HAT breakout boards, as it features the same 40 Pin GPIO as the Raspberry Pi 2/B+/A+

    Raspberry Pi Zero Features:

    • BCM2835 chipset, Overclocked to 1Ghz 
    • 512MB RAM
    • Tiny Form Factor: 65mm x 30mm x 5mm
    • Fully HAT compatible
    • 40pin GPIO (Unpopulated)
    • Stream and watch Hi-definition video output at 1080P
    • Micro SD Slot for OS 
    • Tiny Current Draw ~ 140mA at 5V!
    • Mini-HDMI for Video
    • Micro-USB OTG Host for Data
    • Micro-USB for Power
    • Micro-CSI Camera Port
    Note: As this product is limited to 1 per customer; We reserve the right to cancel multiple and/or duplicate orders.

    Raspberry Pi Operating System Downloads: https://www.raspberrypi.org/downloads/
    Getting Started with Raspberry Pi

    Limited to 1 RPI Zero per customer (including units included in kits), we reserve the right to cancel duplicate and/or multiple orders.
    R194.30  Inc VAT
    Official Raspberry Pi Zero Red & White Case (zero official case red/white)

    The Official Raspberry Pi Zero & Zero Wireless Case is now available! Specially made and beautifully crafted in red & white, this nifty and tactile snap-together case is designed to protect your Zero!

    The case comes with three swappable lids, each with a different function:

    • Raspberry Pi Camera lens holder lid with included extra short 35mm Raspberry Pi Zero camera cable(This cover is for the normal Raspberry Pi camera. The zero camera lens is to small to fit snugly.)
    • GPIO access lid, with GPIO hole for all your hacking needs
    • Solid lid, for those who want an all around protected Zero!

    The Official Raspberry Pi Zero Red & White Case Features:

    • Fabulous Raspberry Red and White Colour Combination
    • 2 Part "Snap-Fit" Enclousure, with 3 separate lids (GPIO/Camera/Solid)
    • Underside slot for GPIO access
    • Cut-outs for all connection points
    • No SD card access (keeps your card protected!)
    • Included 4 x Stick on rubber feet for case stability
    Please note:
    Some mini-HDMI cables will need to have their shroud's cut down to fit the official case.
    The Official Raspberry Pi Zero & Zero Wireless Case is now available!
    R59.90  Inc VAT
    Raspberry Pi1 Model B+ (Pi1 B+)

    Description:

    RASPBERRY PI BOARD, MODEL B+, 512MB

    • Core Architecture:  ARM
    • Core Sub-Architecture:  ARM1176JZF-S
    • No. of Bits:  32bit
    • Silicon Core Number:  BCM2835
    • Silicon Family Name:  BCM2xxx
    • Silicon Manufacturer:  Broadcom
    • Clock Frequency Max:  700MHz

    Specification: 

    • 40 Pin extended GPIO header
    • x4 USB 2 ports up to 1.2A
    • Combined 4-pole jack for stereo audio and composite video output
    • MicroSD card slot for loading your operating system and storing data
    • Micro USB power source(Power supply not included)
    • CSI and DSI for connecting the Raspberry Pi camera and touchscreen display
    • The first x26 GPIO pins are 100% backward compatible with Model B
    • HDMI video output for 1080P Hi-definition video
    • 10/100 Ethernet port for network connectivity
    • More energy efficient

    Legislation and Environmental

    • RoHS Compliance:  Yes

     

    Contents:

    • 1 x Raspberry Pi Model B+

    What else do I need?:

    Resources:


    R529.90  Inc VAT
    Raspberry Pi 2 - Model B (Pi2 B)

    Description:

    The Raspberry Pi 2 Model B has landed at PiShop! The  ultra-low-cost, deck-of-cards sized Linux computer has had yet another  makeover, this time the Raspberry Pi Foundation have gone all out! The Raspberry Pi 2 Model B is on a completely new level to its predecessors by being a staggering 6x faster than the Raspberry Pi Model B+.

    Back-Compatibility note: The Raspberry Pi 2 Model B has the same footprint and layout as the previous Model B+ version, so will fit all Model B+ items.

    Raspberry Pi 2 Model B Features:

    • 6x Faster - Broadcom BCM2836 ARMv7 Quad Core Processor powered Single Board Computer running at 900MHz
    • Double Memory - 1GB RAM so you can now run bigger and more powerful applications
    • Identical  board layout and footprint as the Model B+, so all cases and 3rd party  add-on boards designed for the Model B+ will be fully compatible.
    • Fully HAT compatible
    • 40pin  extended GPIO to enhance your “real world” projects. GPIO is 100%  compatible with the Model B+ and A+ boards. First 26 pins are identical  to the Model A and Model B boards to provide full backward compatibility  across all boards.
    • Connect a Raspberry Pi camera and touch screen display (each sold separately)
    • Stream and watch Hi-definition video output at 1080P
    • Micro SD slot for storing information and loading your operating systems.
    • Advanced power management:
    • You  can now provide up to 1.2 Amp to the USB ports – enabling you to  connect more power hungry USB devices directly to the Raspberry PI.  (This feature requires a 2Amp micro USB Power Supply)
    • 10/100 Ethernet Port to quickly connect the Raspberry Pi to the Internet
    • Combined 4-pole jack for connecting your stereo audio out and composite video out

    Specifications:

    • Broadcom BCM2836 ARMv7 Quad Core Processor powered Single Board Computer running at 900MHz
    • 1GB RAM
    • 40pin extended GPIO
    • 4 x USB ports
    • 4 pole Stereo output and Composite video port
    • Full size HDMI
    • CSI camera port for connecting the Raspberry Pi camera
    • DSI display port for connecting the Raspberry Pi touch screen display
    • Micro SD port for loading your operating system and storing data
    • Micro USB power source

    Contents:

    • 1 X Raspberry Pi 2 - Model B

    Resources:

    R719.90  Inc VAT
    Raspberry Pi Sense HAT (Sense Hat)

    The Sense HAT is an add-on board for Raspberry Pi, made especially for the Astro Pi mission! It’s going to the International Space Station in December 2015 – and is now available to buy from PiShop.

    The Sense HAT has an 8×8 RGB LED matrix, a five-button joystick and includes the following sensors:

    • 3D Gyroscope
    • Accelerometer (Yaw, Pitch & Roll)
    • Magnetometer
    • Temperature
    • Barometric Pressure
    • Humidity

    The Raspberry Pi Foundation have also created a Python library providing easy access to everything on the board.

    Sensing Elements Technical Specification:

    Pressure / Temperature (ST Micro LPS25H)
    – 24-bit pressure measurement resolution (260hPa to 1260hPa)
    – 16-bit temperature measurement resolution (0-125°C)
    Datasheet

    Humidity / Temperature (ST Micro HTS221)
    – 16-bit humidity measurement resolution (0-100% relative humidity)
    – 16-bit temperature measurement resolution (0-60°C)
    Datasheet

    Acceleration/Gyroscope/Magnetic field (ST Micro LSM9DS1)
    – 9 degrees of freedom (X, Y, Z independent axes for all sensors)
    – ±16 g acceleration measurement range
    – ±16 gauss magnetometer measurement range
    – ±2000 dps (degrees per second) gyroscope measurement range
    Each of these measurement channels has 16 bits of resolution.
    Datasheet

    All of these sensors have features for periodic sampling of sensor values, complete with internal FIFO storage. The LPS25H and HTS221 have maximum sample rates of 25 per second, the LSM9DS1 has a maximum sample rate of 952Hz

    LED Matrix
    The LED matrix is driven by a combination of a constant-current LED driver and an Atmel ATTiny88 running a custom firmware that delivers an 8×8 display with 15-bit resolution RGB colour. If you want to get into the gory details, the AVR firmware is available on Github.

    Joystick
    The Atmel is responsible for sampling the joystick. We didn’t have enough pins left on the Atmel to dedicate the five that we needed to sample the joystick axes independently, so they’ve been spliced into the LED matrix row selects. The joystick gets updated at approximately 80Hz, which is the scan rate of the LED matrix.

    All of the sensors (and the base firmware for the Atmel) are accessible from the Pi over I2C. As a fun bonus mode, the SPI peripheral on the Atmel has been hooked up to the Pi’s SPI interface – you can reprogram your HAT in the field! We use this method to get the firmware into the Atmel during production test – and we leave it unprotected so you can substitute the stock firmware to get it to do whatever you want. Seriously. First person to turn this sensor HAT into a quadcopter controller HAT wins a cookie from me.

    Getting Started

    Connect your Sense HAT to the Raspberry Pi via the 40 GPIO Pins.You will then need to install the software:

    Open up a terminal and run the following command:

    wget -O - http://www.raspberrypi.org/files/astro-pi/astro-pi-install.sh --no-check-certificate

    When the install has finished you will need to reboot your Raspberry Pi!

    Getting started with the Raspberry Pi Sense HAT


    R599.90  Inc VAT
    Per Page      1 - 20 of 63